

Esp32-s3-wroom1
Hardware design and bring-up repository for a custom ESP32-S3 dual-core microcontroller board designed in KiCad.
- Size
- 51.9 × 63.7 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 60
- Nets
- 64
- Pads
- 257
- Tracks, vias
- 398, 89
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 1 Oct 2026
- Updated
- 1 Oct 2026
Overview
Esp32-s3-wroom1 is an open-source printed circuit board by xbtry, from the xbtry/esp32s3-dev-board-v0 repository on GitHub. It is a 4-layer board of 51.9 × 63.7 mm with 60 parts on 64 nets, routed with 398 tracks and 89 vias.
It is built around the ESP32-S3-WROOM-1-N8, ICP-20100 and TPS54302, with the ICM-42670-P among its other parts. Its parts include 18 capacitors, 18 resistors, 7 diodes, 2 connectors and 1 IC. It belongs with the ESP32 boards of this library.
Main components
4ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesICP-20100
LGA-10L-40℃~+85℃ 1.8V、3.3V 1pa 2.65uA 20pa 30Kpa~1.1bar I2C、SPI、I3C Temperature Sensor LGA-10L Pressure Sensors ROHSTDK InvenSensePressure SensorsTPS54302
UncategorisedTexas InstrumentsICM-42670-P
LGA-14(2.5x3)-40℃~+85℃ 1.71V~3.6V 16bit 2.25KB 3.5uA IMU (accelerometer + gyroscope) Motion event detection SPI、I2C、I3C X,Y,Z X,Y,Z ±16g ±2000dps LGA-14(2.5x3) Accelerometers ROHSTDK InvenSenseAccelerometers
README
README.mdCustom ESP32-S3 Development Board & Bring-Up
Hardware design and bring-up repository for a custom ESP32-S3 dual-core microcontroller board designed in KiCad.
Hardware Specifications
- MCU: ESP32-S3 (Xtensa Dual-Core 32-bit LX7)
- Power & Data: Native USB Type-C interface
- Form Factor: Custom multi-layer PCB
Verification & Bring-Up Status
- Schematic & Layout Verification
- Board Assembly & SMD Reflow
- Power Supply Stability & Core Rail Check
- Native USB Boot & ROM Bootloader Detection
- Peripheral bus expansion (I2C/SPI) - Planned for Rev 2
Tools Used
- EDA: KiCad
- Firmware: ESP-IDF / C
- Lab Instruments: Digital Oscilloscope, Logic Analyzer, Multimeter
Parts
60| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C2, C3, C11, C13, C15, C16, C18 |
| 5 | 330 | Resistor_SMD:R_0805_2012Metric | R10, R11, R12, R13, R14 |
| 5 | LED | LED_SMD:LED_0805_2012Metric | D3, D4, D5, D6, D7 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric | R3, R8, R9, R18 |
| 4 | 4.7k | Resistor_SMD:R_0805_2012Metric | R4, R5, R15, R16 |
| 4 | Conn_01x04_Pin | Connector_JST:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical | GPIO_A, GPIO_C, I2C_2, TRX |
| 2 | 10nF | Capacitor_SMD:C_0805_2012Metric | C7, C12 |
| 2 | 22uF | Capacitor_SMD:C_0805_2012Metric | C8, C9 |
| 2 | 22uF | Capacitor_SMD:C_1206_3216Metric | C4, C5 |
| 2 | 5.1k | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | D_Schottky | Diode_SMD:D_SMA_Handsoldering | D1, D2 |
| 1 | 100k | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 10uF | Capacitor_SMD:C_0805_2012Metric | C17 |
| 1 | 10uF | Capacitor_SMD:C_1206_3216Metric | C1 |
| 1 | 1uF | Capacitor_SMD:C_0805_2012Metric | C10 |
| 1 | 2.2uF | Capacitor_SMD:C_0805_2012Metric | C14 |
| 1 | 22.1k | Resistor_SMD:R_0805_2012Metric | R7 |
| 1 | 33k | Resistor_SMD:R_0805_2012Metric | R17 |
| 1 | 47pF | Capacitor_SMD:C_0805_2012Metric | C6 |
| 1 | 6.8uH | Inductor_SMD:L_Taiyo-Yuden_NR-40xx | L1 |
| 1 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | PWR |
| 1 | Conn_01x06_Pin | Connector_JST:JST_SH_BM06B-SRSS-TB_1x06-1MP_P1.00mm_Vertical | SPI |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 |
| 1 | ICM-42670-P | Sensor_Motion:ICM42670P | IMU |
| 1 | ICP-20100 | Sensor_Pressure:ICP-20100_IVS | BAR |
| 1 | Micro_SD_Card_Det1 | Connector_Card:microSD_HC_Hirose_DM3AT-SF-PEJM5 | J1 |
| 1 | SW_Push | Button_Switch_SMD:SW_Push_1P1T_NO_E-Switch_TL3301NxxxxxG | RESET |
| 1 | TPS54302 | Package_TO_SOT_SMD:SOT-23-6 | U2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
The 57 most common of 60 parts.
Similar boards
- 4 layers72.5 × 85.4 mm

- 4 layers50 × 70 mm

- 6 layers51 × 53.5 mm

Custom fc rat
Ekta-Gupta27/custom-flight-controller-pcb
Custom flight controller PCB designed in KiCad with STM32F7, multiple sensors, CAN, USB, telemetry, PWM and IO interfaces.
122 parts - 2 layers65.1 × 35 mm

- 4 layers40 × 65 mm

- 4 layers40 × 65 mm

- 2 layers102.7 × 40 mm

- 4 layers35 × 99.9 mm

Snips controller
thePunderWoman/SnipsControllers
The controllers built to work with Amidala
95 parts3GPL-2.0
Questions
How big is the Esp32-s3-wroom1 PCB?
It measures 51.9 × 63.7 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Esp32-s3-wroom1 use?
60 parts, built around the ESP32-S3-WROOM-1-N8, ICP-20100, TPS54302 and ICM-42670-P. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Esp32-s3-wroom1 KiCad files?
From the xbtry/esp32s3-dev-board-v0 repository on GitHub, at the commit this page was made from: the board is esp32-s3-wroom1.kicad_pcb and its schematic esp32-s3-wroom1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Esp32-s3-wroom1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask xbtry before reusing the design.