

YAKB controller B1
Yet Another (HH) KB
- Size
- 82 × 24 mm
- Copper layers
- 2
- Thickness
- 1 mm
- Parts
- 8
- Nets
- 22
- Pads
- 58
- Tracks, vias
- 242, 21
- Pours
- 5
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 21 Oct 2026
- Updated
- 23 Oct 2026
Overview
YAKB controller B1 is an open-source printed circuit board by wZuck, from the wZuck/YAKB repository on GitHub, published under the MIT licence. It is a 2-layer board of 82 × 24 mm with 8 parts on 22 nets, routed with 242 tracks and 21 vias.
Its parts include 2 capacitors and 1 IC. It belongs with the nRF52 and nRF5x boards of this library.
README
README.mdYAKB — Yet Another KeyBoard
简体中文 · B1.1 soldering workbench · Assembly notes · File/revision map
The current assembly is the B1.1 engineering prototype: NiZ electrocapacitive mechanisms, a fixed 60-key HHKB layout, centered-stem 6u spacebar, nice!nano v2 / nRF52840 and ZMK, USB / BLE and a protected 1S battery.
The controller sits on a rear-left carrier, with USB-C directly accessible from the left side. Mainboard U1 takes only a passive interposer: do not install a second controller there. PCB, plate, case, fabrication files and geometry-based renders are supplied. Physical assembly, noise, RF, temperature and runtime remain untested. Qualify NiZ/stabilizer coupons, the short FPC and the rear-pod coupon before a complete build.

| Item | Current B1.1 definition |
|---|---|
| Layout | 60 keys, HHKB Control position, split right Shift + Fn; left blocker 1.5u, right 2.5u; centered 6u space with 95.25 mm stabilizer spacing |
| Mechanism / plate | NiZ housing, MX-cross slider, silencing ring, separate dome and sensing conical spring; 1.6 mm plate with initial 14.0 mm R0.5 cutouts; qualify in final material |
| Sensing mainboard | Shared A0 four-layer board, 285 × 94.6 × 1.6 mm; no MCU at U1 |
| Daughterboards / FPC | 82 × 24 × 1 mm carrier, 40 × 19 × 1 mm interposer; 24-conductor custom shaped FPC and Molex 200528-0240 connectors |
| Hand assembly | Mainly SOIC, 0805 and through holes; the 1 mm-pitch FPC connectors need flux and magnification; no bare MCU, crystal or RF network assembly |
| Power | Protected 1S, approximately 100 mA default charging, BOOST open; multiple pouches require a factory 1S2P / 1S3P pack with one protection board |
| USB / BLE | Direct to the carrier's nice!nano; Fn+5 selects USB, Fn+6 selects BLE; one reporting endpoint at a time |
| Case | Dedicated B1 base and pod lid with shared A0 HHKB bezel and plate; maximum plan envelope 299 × 136.6 mm, with 28 mm extra depth only at the rear-left pod; no visible top screws |
| Case compatibility | Mainboard mounts reference GH60 / Lot60; the B1 pod is not a universal drop-in fit for commercial GH60 / Poker cases |
B1.1 has 46 populated board/harness positions + one FPC, plus one mainboard-U1 DNP record and 60 unsoldered sensing cells. No per-key diodes, hot-swap sockets, RGB, display or separate USB controller are used.
File entry points:
- Complete electronics BOM, module/case delta BOM, FPC pin map. The electronics BOM excludes batteries, mechanisms and case hardware; use the assembly notes and delta BOM for those.
- Mainboard PCB, mainboard schematic, controller PCB, interposer PCB, custom FPC. The shared mainboard source retains the A0 controller symbol; the consolidated BOM controls B1 population.
- B1 assembly STEP, single-bay base STL, three-bay base STL, pod lid, shared bezel.
- Own-case plate DXF, NiZ coupon, short-FPC ZIP, rear-pod print coupon. DXF units are mm; do not cut
REFERENCE. - Interface corrections and qualification, firmware/flashing, reproduction, sources/licenses.
Scripts check native electrical reports, selected solid clearances, fabrication ZIPs and render hashes. See reports and the consistency audit for coverage and pending physical tests. File checks do not certify hardware operation.
A0 is the baseline for the shared mainboard, bezel and plate. Its historical workbench, case record, base electrical analysis and battery study are explicitly scoped. The A0 base and incomplete USB extension arrangement are not used by the current B1 assembly.
Original YAKB files use MIT; reused Tako / KiCad library material retains its own licenses. See the source record for attribution boundaries.
Parts
8| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | H1, H2, H3, H4 | ||
| 1 | 100nF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2 |
| 1 | 1nF_C0G | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1 |
| 1 | Molex 200528-0240 | Connector_FFC-FPC:Molex_200528-0240_1x24-1MP_P1.00mm_Horizontal | JF1 |
| 1 | nice!nano_v2 | YAKB:nice_nano | U1 |
More from wZuck/YAKB
4- 4 layers285 × 94.6 mm

- 2 layers40 × 19 mm

- 2 layers26.1 × 25 mm

- 2 layers225.1 × 98.6 mm

Similar boards
- 2 layers20.5 × 24.8 mm

- 2 layers14.4 × 10.5 mm

OSO SWAB B1-00 Sensor Watch Accelerometer
joeycastillo/Sensor-Watch
A board replacement for the classic Casio F-91W wristwatch
8 parts2.1k - 2 layers7.9 × 39.1 mm

Brain board STM32F407 SD wing it
rusefi/rusefi
rusefi - GPL internal combustion engine control unit
8 parts1.2k - 2 layers59.9 × 25.7 mm

Buffer
hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI
8 parts1kGPL-3.0 - 2 layers52 × 12.6 mm

USB
shanteacontrols/OpenDeck
A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.
8 parts960Apache-2.0 - 2 layers87.5 × 48.5 mm

7 input macropad
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
8 parts915 - 2 layers36.2 × 63.1 mm

PicoMemcard pico
dangiu/PicoMemcard
Emulating PSX Memory Card (or controller) using a Raspberry Pi Pico
8 parts694GPL-3.0 - 2 layers36 × 10 mm

PCB4-PWR BTN Rev.A
OLIMEX/DIY-LAPTOP
Do It Yourself Open Source Hardware and Software Modular Hacker's Friendly Laptop
8 parts578Apache-2.0
Questions
How big is the YAKB controller B1 PCB?
It measures 82 × 24 mm and has 2 copper layers, 1 mm thick.
What parts does the YAKB controller B1 use?
8 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the YAKB controller B1 KiCad files?
From the wZuck/YAKB repository on GitHub, at the commit this page was made from: the board is hardware/modular/YAKB-controller-B1.kicad_pcb and its schematic hardware/YAKB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the YAKB controller B1 design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).