Skip to the content
2 layers90 × 80 mmLinefollower, the printed circuit board in 3D

Linefollower

wuehr1999/Schnuffi

A small linefollowing and micromouse robot

Size
90 × 80 mm
Copper layers
2
Thickness
1.6 mm
Parts
91
Nets
63
Pads
291
Tracks, vias
692, 178
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
16 May 2021
Updated
16 May 2021

Overview

Linefollower is an open-source printed circuit board by wuehr1999, from the wuehr1999/Schnuffi repository on GitHub, published under the MIT licence. It is a 2-layer board of 90 × 80 mm with 91 parts on 63 nets, routed with 692 tracks and 178 vias.

It is built around the DRV8833PW. Its parts include 33 resistors, 15 capacitors, 14 connectors, 12 ICs and 4 switches. It belongs with the STM32 boards of this library.

Main components

1

README

README.md

Schnuffi

A small linefollowing and micromouse robot.

Sensors

  • 9 ITR1201 light sensors
  • 5 VL53L0X tof sensors
  • HAL Encoder input for each motor

Parts

91
QtyValueFootprintReferences
1810kresistors:R_0603R1, R2, R3, R10, R11, R12, R13, R17, R18, R19, R20, R21, R22, R23, R24, R25 +2
9220resistors:R_0603R26, R27, R28, R29, R30, R31, R32, R33, R34
9ITR1201IC_sensor:ITR1201U8, U9, U10, U11, U12, U13, U14, U15, U18
8100nFcapacitors:C_0603C2, C4, C7, C8, C9, C10, C11, C13
6MHP_3.2_5.8MECH_mounting_holes:MHP_3.2_5.8MECH1, MECH2, MECH3, MECH4, MECH5, MECH6
5CONN_01X06Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_VerticalP10, P11, P12, P13, P14
31kresistors:R_0603R9, R14, R15
3CONN_01X02Connector_PinSocket_2.54mm:PinSocket_1x02_P2.54mm_VerticalP3, P4, P6
3Led_SmallLEDs:LED_0603D1, D2, D3
3SW_PUSHmechanical-switches:smd_pushSW1, SW3, SW4
2100Rresistors:R_0805R4, R5
210uFcapacitors:C_1206C6, C12
220pFcapacitors:C_0603C14, C15
2CONN_01X01wire_pads:SolderWirePad_single_1mmSMDP7, P9
2CONN_01X03Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_VerticalP2, P5
2CONN_01X04Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_VerticalP1, P8
110nFcapacitors:C_0603C3
11Mresistors:R_0603R16
12.2uFcapacitors:C_0603C1
1CP_Smallcapacitors:TantalC_SizeX_EIA-7343C5
1Crystal_SMD_4Padcrystals:Crystal_SMD_0603_4PadsY1
1DRV8833SSOP:TSSOP-16-1EP_4.4x5mm_Pitch0.65mmU1
1LT1117SOT_TO:SOT-223U4
1Labellabels:jecc_logo_7.2x2.2L1
1Labellabels:BotL2
1Labellabels:TopL3
1STM32F103C8TxQFP:LQFP-48_7x7mm_Pitch0.5mmU3
1switches:Würth_WS-SLTVmechanical-switches:WE_450404015514SW2

Similar boards

  • 2 layers110 × 110 mmMs pcb, the printed circuit board in 3D

    Ms pcb

    opatiny/micromouse

    Designing a custom micromouse robot.

    39 parts15CERN-OHL-P-2.0
  • 4 layers102 × 100 mmZelvicka, the printed circuit board in 3D

    Zelvicka

    RoboticsBrno/Robutek

    Robůtek je robotická platforma založená na čipu ESP32-S3. Je velice rozšitiřelný, ale ze základu umí jezdit, kreslit fixou, jezdit po čáře, pohybovat se bludištěm. Programování je přes Jaculus.

    214 parts12
  • 2 layers60 × 100 mmRobot boosterpack, the printed circuit board in 3D

    Robot boosterpack

    Hylian/BoosterBot

    Turn your TI LaunchPad into a robot!

    62 parts7
  • 2 layers91.9 × 67.1 mmUpdatedPCB2024, the printed circuit board in 3D

    UpdatedPCB2024

    CWRUbotix/Micromouse-2023-24

    A fully autonomous maze-solving not-quite-mouse-sized robot.

    31 parts6GPL-3.0
  • 2 layers119.4 × 98.9 mmPCB Pami, the printed circuit board in 3D

    PCB Pami

    FIPATECH/CDFR26_PAMI

    Open source firmware and PCB for a differential mobile robot (PAMI) based on ESP32-S3 - Coupe de France de Robotique

    25 parts6
  • 2 layers93.6 × 102.8 mmMote hardware, the printed circuit board in 3D

    Mote hardware

    empriselab/mote

    A low cost, high confidence mobile robot optimized for education.

    75 parts5MIT
  • 2 layers104.1 × 76.2 mmBiotracker tracks, the printed circuit board in 3D

    Biotracker tracks

    interspecifics/ComunicacionesEspeculativas

    Es un proyecto basado en una máquina que es capaz de observar y aprender de microorganismos para crear un score audiovisual a partir de los patrones que encuentre en su comportamiento.

    16 parts4
  • 2 layers71.5 × 48.3 mmEsp32-2wd, the printed circuit board in 3D

    Esp32-2wd

    nochkin/esp-line-follower

    A simple educational project to build a line following 2WD robot

    13 parts3MIT

Questions

How big is the Linefollower PCB?

It measures 90 × 80 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Linefollower use?

91 parts, built around the DRV8833PW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Linefollower KiCad files?

From the wuehr1999/Schnuffi repository on GitHub, at the commit this page was made from: the board is kicad/linefollower.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Linefollower design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).