

Power
Re-usable test jig controller
- Size
- 50.8 × 38.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 29
- Nets
- 17
- Pads
- 80
- Tracks, vias
- 117, 41
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 15 Nov 2021
- Updated
- 5 Feb 2024
Overview
Power is an open-source printed circuit board by wntrblm, from the wntrblm/Hubble repository on GitHub. It is a 2-layer board of 50.8 × 38.7 mm with 29 parts on 17 nets, routed with 117 tracks and 41 vias.
It is built around the LM1117-3.3 and LM1117-5.0. Its parts include 6 capacitors, 6 resistors, 6 diodes, 5 connectors and 2 ICs.
Main components
2LM1117-3.3
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 3.3V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorisedLM1117-5.0
SOT-2231 1.3V@(1000mA) 15V 1A 2mA 5V Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHShongjiachengUncategorised
README
README.mdHubble
Hubble is Winterbloom's re-usable development board for test jigs.
Repository layout
This repository contains the hardware design files and firmware files for Hubble.
- firmware/ contains the firmware source code, build scripts, and third-party dependencies. The firmware is written in C using GCC ARM.
- hardware/ contains the hardware design files for the mainboard, jackboard, panel, and programming board. These are all created using KiCAD.
- mechanical/ contains various designs for laser-cut and 3d-printed parts used to modify the stock test jig assembly for Hubble.
License and contributing
Hubble is open-source hardware and software, however, licensing a project like this is a little complicated. Please take a chance to review the LICENSE file.
We welcome contributions! Please read our Contributing Guide and Code of Conduct.
Parts
29| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C1, C2, C3, C4 |
| 4 | 1k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R3, R4, R5, R6 |
| 2 | 0.3-22R | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | 10uF | Capacitor_THT:CP_Radial_D5.0mm_P2.50mm | C5, C6 |
| 2 | BARRIER | winterbloom:D_SOD-123 | D1, D2 |
| 2 | BEAD | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | FB1, FB2 |
| 1 | Blue | LED_THT:LED_D3.0mm | D3 |
| 1 | Eurorack_Power | winterbloom:Eurorack_Power | J1 |
| 1 | Green | LED_THT:LED_D3.0mm | D5 |
| 1 | LM1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U1 |
| 1 | LM1117-5.0 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | LOGO | winterbloom:Extra_Long_Wiggly_Boi_25mm | G*** |
| 1 | Left | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J3 |
| 1 | Left power | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J2 |
| 1 | Power | winterbloom:Switch_DPDT_Thonk_DW4_2.54mm_pitch_5.08mm_spacing | SW1 |
| 1 | Red | LED_THT:LED_D3.0mm | D4 |
| 1 | Right | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | Right power | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J5 |
| 1 | Yellow | LED_THT:LED_D3.0mm | D6 |
More from wntrblm/Hubble
9- 4 layers114 × 120 mm

- 2 layers21.6 × 58.4 mm

- 2 layers100 × 100 mm

- 2 layers27.1 × 24 mm

- 2 layers27.1 × 24 mm

- 2 layers26.9 × 68.6 mm

- 2 layers27.1 × 18.5 mm

- 2 layers21.5 × 26.5 mm

- 2 layers26.7 × 27.9 mm

Similar boards
- 2 layers84.3 × 58.4 mm

EnocderDriver
NikodemBartnik/Small-Projects
All of smaller projects (Arduino, PCBs, electronics, code)
35 parts55 - 2 layers97 × 97 mm

QO100 RX
barisdinc/N3B_SDR_Transceiver_HW
V/U/SHF and QO-100 SDR Transceiver Project
167 parts20GPL-3.0 - 2 layers85 × 60 mm

BaseModule
KarlVaello/VehicleControlSystem
Vehicle Control System. Using C++ Qt and C. Hardware and Software
67 parts14GPL-3.0 - 2 layers40 × 100 mm

MidiMonger components
dchwebb/MidiMonger
Eurorack MIDI interface supporting USB and serial MIDI. Based on ARM STM32F446 MCU.
70 parts12 - 2 layers96 × 100 mm

- 4 layers80.8 × 100 mm

- 2 layers37 × 90 mm

- 4 layers

PicoDevR02
DhruvaG2000/RP2040_Dev_Board
Kicad PCB design for a RP2040 Development Board Designed to make the RP2040 more beginner friendly
16 parts4MIT
Questions
How big is the Power PCB?
It measures 50.8 × 38.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Power use?
29 parts, built around the LM1117-3.3 and LM1117-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Power KiCad files?
From the wntrblm/Hubble repository on GitHub, at the commit this page was made from: the board is hardware/breakouts/power/power.kicad_pcb and its schematic hardware/board/analog-ins-low-voltage.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Power design in my own project?
Its repository states no licence, so its author keeps all rights: ask wntrblm before reusing the design.