
PicoDevR01
DhruvaG2000/RP2040_Dev_Board
Kicad PCB design for a RP2040 Development Board Designed to make the RP2040 more beginner friendly

Kicad PCB design for a RP2040 Development Board Designed to make the RP2040 more beginner friendly
PicoDevR02 is an open-source printed circuit board by DhruvaG2000, from the DhruvaG2000/RP2040_Dev_Board repository on GitHub, published under the MIT licence. It is a 4-layer board with 16 parts on 50 nets, routed with 134 tracks and 0 vias.
It is built around the LM1117-3.3 and LM1117-5.0. Its parts include 2 diodes, 2 connectors, 1 resistor and 1 switch. It belongs with the RP2040 boards of this library.
Kicad PCB design for a RP2040 Development Board Designed to make the RP2040 more beginner friendly



| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | C | Capacitor_THT:CP_Radial_D10.0mm_P2.50mm | C_ip1, C_ip2, C_op1, C_op2 |
| 2 | Conn_01x04_Male | Connector_PinHeader_1.00mm:PinHeader_1x04_P1.00mm_Vertical | 12Vout1, Main_GND1 |
| 1 | 1N4148 | Diode_THT:D_DO-35_SOD27_P7.62mm_Horizontal | D2 |
| 1 | Barrel_Jack | Connector_BarrelJack:BarrelJack_CUI_PJ-063AH_Horizontal | J1 |
| 1 | Conn_01x20_Female | Connector_PinSocket_2.54mm:PinSocket_1x20_P2.54mm_Vertical | pico21to40 |
| 1 | LED | LED_THT:LED_D4.0mm | D1 |
| 1 | LM1117-3.3 | Connector_PinSocket_1.00mm:PinSocket_1x03_P1.00mm_Vertical | LM_3V3 |
| 1 | LM1117-5.0 | Connector_PinSocket_1.00mm:PinSocket_1x03_P1.00mm_Vertical | LM_5 |
| 1 | Pico | picoFootPrint:RPi_Pico_SMD_TH | RP2040Board1 |
| 1 | Pico1to20 | Connector_PinSocket_2.54mm:PinSocket_1x20_P2.54mm_Vertical | J2 |
| 1 | R | Resistor_THT:R_Axial_DIN0411_L9.9mm_D3.6mm_P25.40mm_Horizontal | R1 |
| 1 | SW_Push_Dual | Button_Switch_THT:Push_E-Switch_KS01Q01 | SW1 |

DhruvaG2000/RP2040_Dev_Board
Kicad PCB design for a RP2040 Development Board Designed to make the RP2040 more beginner friendly

NikodemBartnik/Small-Projects
All of smaller projects (Arduino, PCBs, electronics, code)

barisdinc/N3B_SDR_Transceiver_HW
V/U/SHF and QO-100 SDR Transceiver Project

KarlVaello/VehicleControlSystem
Vehicle Control System. Using C++ Qt and C. Hardware and Software

dchwebb/MidiMonger
Eurorack MIDI interface supporting USB and serial MIDI. Based on ARM STM32F446 MCU.




16 parts, built around the LM1117-3.3 and LM1117-5.0. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the DhruvaG2000/RP2040_Dev_Board repository on GitHub, at the commit this page was made from: the board is picoDevR0/picoDevR02.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).