Skip to the content
2 layers99.3 × 98.1 mmPanel c50, the printed circuit board in 3D

MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

Size
99.3 × 98.1 mm
Copper layers
2
Thickness
0.19 mm
Parts
55
Nets
142
Pads
748
Tracks, vias
2,532, 222
Pours
117
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
1 Oct 2026
Updated
7 Nov 2026

Overview

Panel c50 is an open-source printed circuit board by winkleplex10-bit, from the winkleplex10-bit/The-Mac-Pro-Project repository on GitHub. It is a 2-layer board of 99.3 × 98.1 mm with 55 parts on 142 nets, routed with 2,532 tracks and 222 vias.

Its parts include 14 connectors, 7 capacitors and 7 ICs.

README

archive/kicad/macpro62-storage-face/README.md

MP62 Face S storage module SM-1 rev A0: KiCad 9 project

4 × M.2 2280 NVMe behind an ASMedia ASM2824 PCIe Gen3 switch, on the MP62-FACE v0.1 outline. The plan, BOM, cost and RAID analysis are in /workspace/macpro62-storage-board-plan.md. The spec is macpro62-face-module-spec-v0.1.md §11.3 (update 3).

Status: FLOORPLAN, not routed.

  • PCB: outline, holes, stackup (JLC06161H-2116, 6 layers), rule areas (both-side bus-bar keep-outs, core tab, J_PCIE plug zone), and every IC, connector, socket, standoff, inductor and bulk capacitor placed. Only the lug nets are on the PCB.
  • kicad-cli pcb drc: 0 violations, 0 unconnected, 0 footprint errors.
  • Schematic (macpro62-storage-face.kicad_sch, one flat A0 sheet, label connectivity, 154 symbols): kicad-cli sch erc: 0 errors, 0 warnings.

Frame

  • Same as the template. Module frame origin at the outline's bottom-left, viewed from the core side. Spec (X, Y) → KiCad (60 + X, 190 − Y).
  • F = core side (ASM2824 on the die pad, switch support parts ≤ 2 mm).
  • B = outer side (J_PCIE, J_AUX, 4 × M.2, power band).

PLACEHOLDERS (replace before routing)

FootprintWhy
MP62_M2_MKey_SMT_H4.2_PLACEHOLDERGeneric 67-pad M-key pattern (0.5 mm per row, rows offset 0.25), hold-downs and pegs are guesses. Use the LOTES APCI0107-P001A (LCSC C841661) drawing. The card-edge datum (origin) and the 2280 outline on F.Fab are correct per the M.2 form factor
MP62_BGA-492_21x21mm_Layout25x25_P0.8mm_PLACEHOLDERASM2824 ball map under NDA; 0.8 mm pitch assumed
MP62_TI_RNN0018A_VQFN-HR-18_3.5x3.5mm_PLACEHOLDERTPS56C215 HotRod pads; use TI RNN0018A
MP62_M2_Standoff_SMT_M2_Pad5.0Round pad; height must match the socket's card-bottom height (≈ 3.5 mm for H4.2, verify)

Symbols with logical pin numbering: ASM2824, TPS259824, TPS56C215, TLV62585. Real pinouts: M.2 M-key, MCIO 124 (from the spec CSV), GH15, BL24C64A, TMP1075, 74LVC2G07, SPI NOR, LM74700.

Layers

  • User.1: core contact zones.
  • User.2: outer height-zone lines.
  • User.3: connector band.
  • User.4: M.2 card outlines (host parts under a card ≤ 1.6 mm).
  • Dwgs.User: stock X-bracket (not fitted, deviation D-S1 / spec C-19).
  • Cmts.User: notes.

Rebuild

text
python3 tools/make_footprints.py        # template footprints (MP62_Face.pretty)
python3 tools/make_storage_fps.py       # MP62_Storage.pretty
python3 tools/build_storage.py          # PCB floorplan (KiCad 9 pcbnew python)
python3 tools/postprocess.py            # stackup + netclasses (PCIE_85R, REFCLK_85R, PWR_12V, PWR_3V3)
python3 tools/build_sch.py              # MP62_Storage.kicad_sym + schematic
kicad-cli pcb drc --severity-all -o drc_report.txt macpro62-storage-face.kicad_pcb
kicad-cli sch erc --severity-all -o erc_report.txt macpro62-storage-face.kicad_sch
/workspace/cadenv/bin/python tools/floorplan.py   # floorplan_storage_SM1.png

ICD rev 2 (2026-10-02)

  • U13 INA228 (VSSOP-10, FACE_SMB 0x40, ALERT → FACE_SMB_ALERT#) + R520 2 mΩ 2512 between +12V_PROT and +12V_PROT_S (ahead of U2) + C520; B side at (51.5, 143) / (44, 143) / (51.5, 140.5). DRC 0/0, ERC 0, 157 schematic instances. Renders not refreshed.

ICD rev 3 / O-10 (2026-10-04 ≈ 09:10 ET, Aidan approved)

  • J1 (J_PCIE, MCIO 124 RA) X 43.5 → 47.0 (+3.5 mm), narrow-plug courtyard (±21.6). Zero-jog landing at BP fp6 s = +5.0. Nearest B courtyard MH080 0.34 mm; M.2 card bottom Y 28.5 vs J1 body top Y 24.57 (3.9 mm). tools/floorplan.py reads J_PCIE X from face_geom.json.
  • Nothing routed besides the lug nets, so no re-route. DRC 0/0/0, ERC 0/0 (schematic unchanged). floorplan_storage_SM1.png, render_core_side_F.png, render_outer_side_B.png regenerated (kicad-cli svg + rsvg-convert).

Next steps

  1. Get the ASM2824 datasheet and ball map, plus the LOTES drawing.
  2. Replace the placeholders.
  3. Update the PCB from the schematic and place the ≈ 120 small passives.
  4. Route: PCIe Gen3, ≤ 2 vias per lane; 3V3_SSD on the L4 plane plus B-side pours; 12 V pours.
  5. Run DRC and get a JLC quote.

Parts

55
QtyValueFootprintReferences
12TDR_LAUNCHTP1A_T, TP1B_T, TP2A_T, TP2B_T, TP3A_T, TP3B_T, TP4A_T, TP4B_T, TP5A_T, TP5B_T, TP6A_T, TP6B_T
11Fiducial_1mm_Mask2mmFiducial_1mm_Mask2mmFID1, FID2, FID3, FID4, FID5, FID6, FID7, FID8, FID9, FID10, FID11
7100nF 0201 X5R 10V (3V3_MOD)MP62_MOD:C_0201_0603MetricC1_C1, C1_C2, C1_C3, C1_C4, C1_C5, C1_C6, C1_H
7BL24C02F-NTRC (C2828222) 24C02 ID EEPROM @0x50MP62_MOD:DFN-8-1EP_2x3mm_P0.5mm_EP0.61x2.2mmU1_C1, U1_C2, U1_C3, U1_C4, U1_C5, U1_C6, U1_H
7DF40C-50DP-0.4V(51) C424645 -> JMn DF40C-50DS (PMI-50 v2)MP62_MOD:MP62_Hirose_DF40C-50DP-0.4VJ2_C1, J2_C2, J2_C3, J2_C4, J2_C5, J2_C6, J2_H
6MOD-C - HOAUC HYCW417-USBC24-180B (C5342202) SMD + 4 THT shell legs 1.8MP62_MOD:HOAUC_HYCW417-USBC24-180BJ1_C1, J1_C2, J1_C3, J1_C4, J1_C5, J1_C6
4TOOLING_2.0TH1, TH2, TH3, TH4
1MOD-H - HOAUC HYC79-HDMIA19-105 (C711353) 19 SMD (1 row, 0.5) + 3 THT legs D1.3MP62_MOD:HOAUC_HYC79-HDMIA19-105J1_H

More from winkleplex10-bit/The-Mac-Pro-Project

12
  • 6 layersBackplane, the printed circuit board in 3D

    Backplane

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    221 parts
  • 4 layersBackplane, the printed circuit board in 3D

    Backplane

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    152 parts
  • 4 layers104 × 166 mmMacpro62-storage face-2x, the printed circuit board in 3D

    Macpro62-storage face-2x

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    89 parts
  • 6 layers104 × 166 mmMacpro62-storage face, the printed circuit board in 3D

    Macpro62-storage face

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    76 parts
  • 10 layers156 × 167.8 mmMacpro62 am5, the printed circuit board in 3D

    Macpro62 am5

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    57 parts
  • 10 layers156 × 167.8 mmMacpro62 lga1700, the printed circuit board in 3D

    Macpro62 lga1700

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    53 parts
  • 2 layers74 × 82.2 mmPanel a25, the printed circuit board in 3D

    Panel a25

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    34 parts
  • 2 layers58 × 34 mmTdr coupon c50, the printed circuit board in 3D

    Tdr coupon c50

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    12 parts
  • 2 layers58 × 19 mmTdr coupon a25, the printed circuit board in 3D

    Tdr coupon a25

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    6 parts
  • 2 layers44.7 × 9.7 mmMod hdmi, the printed circuit board in 3D

    Mod hdmi

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    4 parts
  • 2 layers42.1 × 8.8 mmMod usba, the printed circuit board in 3D

    Mod usba

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    4 parts
  • 2 layers40.1 × 8.8 mmMod usbc, the printed circuit board in 3D

    Mod usbc

    winkleplex10-bit/The-Mac-Pro-Project

    MacPro6,2: open PCB redesign of the Mac Pro Late 2013 (trashcan) with new CPU, GPU/storage face modules, backplane and I/O boards (KiCad).

    4 parts

Similar boards

  • 2 layers229.5 × 95.1 mmSweep high, the printed circuit board in 3D

    Sweep high

    davidphilipbarr/Sweep

    Sweep - a small promicro based keyboard inspired by the Ferris.

    55 parts2.1k
  • 2 layers370 × 11 mmDaylight Disco XXL, the printed circuit board in 3D

    Daylight Disco XXL

    VoronDesign/Voron-Hardware

    Cool Hardware designed by the Voron Design group

    55 parts1.1kGPL-3.0
  • 2 layers370 × 10 mmE3NGLEDstick, the printed circuit board in 3D

    E3NGLEDstick

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    55 parts915
  • 2 layers139.3 × 94.8 mmFlake, the printed circuit board in 3D

    Flake

    lever-tech/flake

    An open-source, wireless, split ergonomic keyboard designed to be productive, healthy, and enjoyable. [formerly Anywhy Flake]

    55 parts531CERN-OHL-W-2.0
  • 2 layers237.5 × 102.9 mmMemory, the printed circuit board in 3D

    Memory

    jes/scamp-cpu

    A homebrew 16-bit CPU with a homebrew Unix-like-ish operating system.

    55 parts301Unlicense
  • 2 layers60.6 × 24.1 mmBlep hackerboard, the printed circuit board in 3D

    Blep hackerboard

    CRImier/MyKiCad

    My KiCad boards. Can't be bothered uploading individually anymore, so here you go.

    55 parts253GPL-3.0
  • 2 layers100 × 96.5 mmKeyboard ch552-36-lhs, the printed circuit board in 3D

    Keyboard ch552-36-lhs

    rgoulter/keyboard-labs

    Repo with my PCB designs and keyboard firmware

    55 parts236
  • 2 layers190.5 × 85.7 mmDissatisfaction30, the printed circuit board in 3D

    Dissatisfaction30

    dcpedit/dissatisfaction30

    To get the PCB manufactured, upload dissat-pcb.zip to JLCPCB, select your desired PCB color while keeping all the other default options, and place your order (minimum 5).

    55 parts147CC-BY-4.0

Questions

How big is the Panel c50 PCB?

It measures 99.3 × 98.1 mm and has 2 copper layers, 0.19 mm thick.

What parts does the Panel c50 use?

55 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Panel c50 KiCad files?

From the winkleplex10-bit/The-Mac-Pro-Project repository on GitHub, at the commit this page was made from: the board is boards/io/modules/panel/panel_c50/panel_c50.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Panel c50 design in my own project?

Its repository states no licence, so its author keeps all rights: ask winkleplex10-bit before reusing the design.