
SplitFlapDriverATtiny1616V4
adamgmakes/SplitFlapDisplay
A modular, 3D-printed split-flap display controllable over RS485 from a Raspberry Pi. Each module holds 64 characters and modules can be chained together to build a display of any width.

nodemcu breakout board and software to drive an overview titan
Polariser drive is an open-source printed circuit board by WillMatthews, from the WillMatthews/esp-i2c-titan repository on GitHub, published under the Unlicense licence. It is a 2-layer board of 64 × 46.5 mm with 17 parts on 36 nets, routed with 118 tracks and 57 vias.
It is built around the SPX3819M5-L-5-0 and JACK-C-PC-10A-RA(R). Its parts include 3 connectors, 2 capacitors, 2 resistors, 2 ICs and 1 fuse. It belongs with the ESP8266 boards of this library.
nodemcu breakout board to drive overview titan
Contains the PCB layout to drive an Overview titan through flatflex connector J2.
Contains the arduino code required to program an ESP8266 nodeMCU dev board to interface with the polariser.
Contains MATLAB code to interface with the ESP8266 over a serial interface.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 3 | TestPoint | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP2, TP3 |
| 2 | 1K5 | Resistor_SMD:R_0805_2012Metric | R2, R3 |
| 2 | FlatFlex Molex | flatflex:9pos | J2, J3 |
| 2 | MountingHole | MountingHole:MountingHole_4.3mm_M4 | H1, H2 |
| 2 | TestPoint | Connector_PinHeader_2.54mm:PinHeader_1x01_P2.54mm_Vertical | TP4, TP5 |
| 1 | 0.1n | Fuse:Fuse_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C1 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C2 |
| 1 | Fuse | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | F1 |
| 1 | JACK-C-PC-10A-RA(R) | globteck:GLOBTECK_JACK-C-PC-10A-RA(R) | J1 |
| 1 | NodeMCU_Amica_R2 | nodemcu:NodeMCU_Amica_R2 | U2 |
| 1 | SPX3819M5-L-5-0 | Package_TO_SOT_SMD:SOT-23-5 | U1 |

adamgmakes/SplitFlapDisplay
A modular, 3D-printed split-flap display controllable over RS485 from a Raspberry Pi. Each module holds 64 characters and modules can be chained together to build a display of any width.




XuanTrace/half-bridge-load-cells-board
Open-source half-bridge load cell PCB design featuring the HX710A/B/C ADC chip. Supports SMD with castellation (half-hole), pin headers, and XH2.45 4-pin connectors.


eluluke/Quadruped-Robot
Open-source, 3D-printable, modular quadruped robot designed as a hardware platform for robotics education, controls development, kinematics, reinforcement learning, robotic vision, and future semi-commercial research…

It measures 64 × 46.5 mm and has 2 copper layers, 1.6 mm thick.
17 parts, built around the SPX3819M5-L-5-0 and JACK-C-PC-10A-RA(R). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the WillMatthews/esp-i2c-titan repository on GitHub, at the commit this page was made from: the board is Kicad/polariser_drive.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Unlicense licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).