

Inverter igbt driver
IGBT driver for Electric Vehicle Inverter
- Size
- 84.5 × 64 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 70
- Nets
- 45
- Pads
- 194
- Tracks, vias
- 445, 28
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 4
- Created
- 31 Mar 2018
- Updated
- 11 May 2018
Overview
Inverter igbt driver is an open-source printed circuit board by willjschmitt, from the willjschmitt/inverter-igbt-driver repository on GitHub, published under the MIT licence. It is a 2-layer board of 84.5 × 64 mm with 70 parts on 45 nets, routed with 445 tracks and 28 vias.
It is built around the IXDF604SIA, FOD8316 and 74LVC1G80GV, with the NE555 among its other parts. Its parts include 26 capacitors, 12 resistors, 8 ICs, 8 diodes and 1 connector. It belongs with the power boards of this library.
Main components
4IXDF604SIA
SOIC-8-40℃~+125℃ 2 29ns 35ns 3V 4.5V~35V 4A 4A 800mV 8ns 9ns Enable shutdown、Interleaved conduction protection IGBT、MOSFET Low Side SOIC-8 Gate Drivers ROHSLittelfuse/IXYSGate DriversFOD8316
SOIC-16-300mil-40℃~+100℃ 1 15V~30V 2.5A 250ns 250ns 25ns 25ns 35kV/us 3V~5.5V 4.243kV 600mW IGBT SOIC-16-300mil Gate Drive Optocoupler ROHSonsemiGate Drive Optocoupler74LVC1G80GV
SOT353Single D-Type Flip-Flop; Positive-Edge TriggerNexperiaUncategorisedNE555
SOP-8-20℃~+70℃ 1 1.5mA 200mA 4.5V~15V Adjustable duty cycle oscillation、Reset function、Duty cycle stabilization SOP-8 555 Timers / Counters ROHSGRTimers / Counters
README
README.mdinverter-igbt-driver
IGBT driver for Electric Vehicle Inverter
This project is a work in progress to design a simple IGBT driver for use with the controls designed in https://github.com/willjschmitt/electric-vehicle-controller.
Board is designed in KiCad.
Getting Started
git clone https://github.com/willjschmitt/inverter-igbt-driverInstall KiCad. Open up the KiCad project!
Parts
70| Qty | Value | Footprint | References |
|---|---|---|---|
| 22 | 10u | Capacitors_SMD:C_1206_HandSoldering | C2, C3, C10, C11, C12, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25, C26 +6 |
| 15 | TEST | inverter-igbt-driver:TP RCT (0805) | TP1, TP2, TP3, TP4, TP5, TP6, TP7, TP8, TP9, TP10, TP12, TP15, TP16, TP17, TP18 |
| 7 | 1k | Resistors_SMD:R_0402 | R4, R5, R6, R7, R8, R9, R10 |
| 6 | D_Schottky | Diodes_SMD:D_SOD-123F | D1, D2, D3, D6, D7, D8 |
| 2 | 100 | Resistors_SMD:R_1206_HandSoldering | R2, R13 |
| 2 | 100p | Capacitors_SMD:C_1206_HandSoldering | C13, C15 |
| 2 | 8 | Resistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R3, R14 |
| 2 | D | inverter-igbt-driver:DO-214AC | D4, D5 |
| 2 | FOD8316 | Housings_SOIC:SOIC-16W_7.5x10.3mm_Pitch1.27mm | U3, U5 |
| 2 | Transformer_2P_2S | inverter-igbt-driver:FS48-050-C2 | U6, U8 |
| 1 | 0.001n | Capacitors_SMD:C_0603_HandSoldering | C1 |
| 1 | 0.01u | Capacitors_SMD:C_0603_HandSoldering | C14 |
| 1 | 5.6k | Resistors_SMD:R_0603_HandSoldering | R11 |
| 1 | 74LVC1G80GV | TO_SOT_Packages_SMD:SOT-353_SC-70-5_Handsoldering | U4 |
| 1 | CONTROL | Pin_Headers:Pin_Header_Straight_1x11_Pitch2.54mm | J1 |
| 1 | IGBT_HALF_BRIDGE | inverter-igbt-driver:MG06600WB-BN4MM | U9 |
| 1 | IXDF604SIA | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U2 |
| 1 | NE555 | Housings_SOIC:SOIC-8_3.9x4.9mm_Pitch1.27mm | U1 |
Similar boards
- 4 layers180.3 × 114.9 mm

- 2 layers297.2 × 180.3 mm

- 2 layers203.2 × 149.9 mm

- 2 layers

LM80C R6
leomil72/LM80C
A Z80-based homebrew computer withTMS9918, AY-3-8910, Z80 CTC, Z80 PIO, and Z80 SIO
153 parts123GPL-3.0 - 2 layers249.9 × 89.4 mm

CSCvon8
DoctorWkt/CSCvon8
A crazy small 8-bit CPU built with only seventeen 7400-series chips.
55 parts112GPL-3.0 - 2 layers160.1 × 101 mm

PLC-14500
nicolacimmino/PLC-14500
Retro trainer board based on the MC14500 1-bit ICU. The project is OSHW certified and a ready to assemble kit is available on Tindie.
173 parts70GPL-3.0 - 2 layers63 × 46 mm

Pi485
bvarner/pi485
An open-source TTL UART <-> RS485 converter, intended for a Raspberry Pi or Arduino
31 parts41MIT - 2 layers9.9 × 110.1 mm

ADSR
kraakenstuff/ADSR
2HP ADSR module based on "Fastest Envelope in the West" by René Schmitz (https://www.schmitzbits.de/adsr.html)
44 parts37
Questions
How big is the Inverter igbt driver PCB?
It measures 84.5 × 64 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Inverter igbt driver use?
70 parts, built around the IXDF604SIA, FOD8316, 74LVC1G80GV and NE555. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Inverter igbt driver KiCad files?
From the willjschmitt/inverter-igbt-driver repository on GitHub, at the commit this page was made from: the board is inverter-igbt-driver.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Inverter igbt driver design in my own project?
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).