
Deflection controller
wezelball/crt_esp
A hardware and software build of a CRT controlled by an ESP32

A hardware and software build of a CRT controlled by an ESP32
Esp32 digital is an open-source printed circuit board by wezelball, from the wezelball/crt_esp repository on GitHub, published under the MIT licence. It is a 2-layer board with 20 parts on 41 nets.
It is built around the L4931ABD33-TR and L7805ABD2T-TR. Its parts include 6 capacitors, 4 ICs, 2 resistors, 2 diodes and 1 connector. It belongs with the ESP32 boards of this library.
esp32_digitalKiCad project for the digital board: MCU, power regulation, and the SPI/control link out to the analog board.
docs/journal/build_notes.tex, 2026-03-02): ESP32-
S3-DevKitC-1, internal antenna for the prototype wooden enclosure,
switching to external antenna for the eventual metal enclosure.
Check this against docs/datasheets/, which currently holds ESP32-S2
documentation — confirm which module the schematic actually targets
before finishing routing.due_level_shifter_* files are leftovers from the earlier Arduino Due
shield approach (see journal, "Arduino Due" section) — the project
since moved to a standalone ESP32 board rather than a Due shield. Keep
for reference/history but they're not part of the current design.Document the connector pinout here once finalized (SPI clock/MOSI, CS, LDAC, plus power).
In progress — see docs/journal/ for current bring-up notes.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | MountingHole | MountingHole:MountingHole_2.7mm_M2.5 | H1, H2, H3, H4 |
| 3 | 470uF | Capacitor_THT:CP_Radial_D8.0mm_P3.80mm | C2, C5, C6 |
| 2 | 1N4004 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D2, D3 |
| 1 | 0.1u | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 100uF | Capacitor_THT:CP_Radial_D8.0mm_P3.80mm | C4 |
| 1 | 10K | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R2 |
| 1 | 2.2uF | Capacitor_SMD:C_0805_2012Metric | C3 |
| 1 | 56K | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R1 |
| 1 | ESP32-S2-DEVKITC-1-N8R2_gk | lib_fp_gk:ESP32-S3-DevKitC | U1 |
| 1 | L4931ABD33-TR | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | L7805ABD2T-TR | Package_TO_SOT_SMD:TO-263-3_TabPin2 | U2 |
| 1 | L79L05_TO92 | Package_TO_SOT_THT:TO-92_Inline | U3 |
| 1 | Screw_Terminal_01x02 | lib_fp_gk:TerminalBlock_Phoenix_MKDSN-1,5-2-5.08_1x02_P5.08mm_Horizontal | J1 |
| 1 | TestPoint | TestPoint:TestPoint_Pad_2.0x2.0mm | TP1 |

wezelball/crt_esp
A hardware and software build of a CRT controlled by an ESP32

wezelball/crt_esp
A hardware and software build of a CRT controlled by an ESP32


twisted-builds-llc/sloppy_holley_flex-over-can
CAN bus input/output module for Holley Terminator X (also HP/Dominator class ECUs).

Alexanderabad/Alexander_Abad-Microcontroladores-C1-2025
Tareas de Micro C1-2025


Dynacore-dev/PoolGuard
KiCad 10 PCB design for the ESP32 board that this repository's firmware runs on. It regulates power for the ESP32 and a DS18S20 temperature sensor, and switches four 12V output channels for pumps/relays.



20 parts, built around the L4931ABD33-TR and L7805ABD2T-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the wezelball/crt_esp repository on GitHub, at the commit this page was made from: the board is hardware/kicad/esp32_digital/esp32_digital.kicad_pcb and its schematic hardware/kicad/deflection_controller/dac.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).