Skip to the content
2 layers25 × 43 mmOV7670 breakout, the printed circuit board in 3D

Verilog modules required to get the OV7670 camera working

Size
25 × 43 mm
Copper layers
2
Thickness
1.6 mm
Parts
8
Nets
19
Pads
58
Tracks, vias
154, 12
Pours
1
Routed
Yes
KiCad
KiCad 5 (file 20170922)
Created
7 Nov 2015
Updated
26 Jul 2018

Overview

OV7670 breakout is an open-source printed circuit board by westonb, from the westonb/OV7670-Verilog repository on GitHub. It is a 2-layer board of 25 × 43 mm with 8 parts on 19 nets, routed with 154 tracks and 12 vias.

It is built around the DALC208SC6. Its parts include 3 resistors, 3 connectors, 1 capacitor and 1 IC. It belongs with the interfaces and adapters boards of this library.

Main components

1

README

README.md

OV7670-Verilog

Verilog modules required to get the OV7670 camera working on the Nexys4-DDR board for MIT's 6.111 Digital Systems Labratory

Introduction

I highly recommend you first read the data sheet for the camera module: http://www.voti.nl/docs/OV7670.pdf In summary OV7670 utilizes a 8 bit parallel bus to output video data along with HREF and VSYNC signals to synchronize frames. A input clock is required which is used as a reference for generating the output pixel output clock that the data is aligned to.

Configuration

The OV7670 requires configuration to output the correct color format with the proper color balance. This is done over SCCB which is a copy of the I2C protocol. This interface is over the camera SIOC and SIOD pins. A configuration module is provided for you which will configure the camera with reasonable settings for RGB565 data output.

Camera Data Capture

A module is provided which interfaces with the 8 bit parallel and the HREF/VSYNC signals to output pixel data, a pixel valid signal, and a frame done signal. This can be interfaced with a frame buffer of your own creation. To fit on the Nexys4-DDR BRAM memory you will have to downsample the image in either terms of size or the size of the stored pixel. It is also possible, although complicated to full frames in the on board DDR memory.

Hardware Configuration

The OV7670 outputs its own pixel clock (PCLOCK) that is synchronized with its data output. This must be connected to the FPGA and you must capture the data in this clock domain. Only some PMOD pins are capable of being used as a clock input. The PCLOCK pin must connect to (JB10) for the right PMOD connectors. If you have two cameras you should be able to get away with using one PCLOCK to capture the data from both as long as you connect the clock input from the cameras to the same source. Any of the other PMOD pins can be used for the other camera signals. The 3.3V supply for the camera can also be sourced from the PMOD connectors.

SCCB Pullup Resistors

The SCCB interface for the camera requires pull up resistors. You need to solder 4.7K resistors from the SIOD and SIOC pins on the camera to the 3.3V supply. You can do this yourself or have the staff in the EDS help you.

Parts

8
QtyValueFootprintReferences
3RResistors_SMD:R_0805R101, R102, R103
2CONN_02X06Pin_Headers:Pin_Header_Straight_2x06P102, P103
1CCapacitors_SMD:C_0805C101
1CONN_02X10Pin_Headers:Pin_Header_Straight_2x10P101
1DALC208TO_SOT_Packages_SMD:SOT-23-6U101

More from westonb/OV7670-Verilog

1
  • 2 layers19.5 × 28 mmCamera side breakout, the printed circuit board in 3D

    Camera side breakout

    westonb/OV7670-Verilog

    Verilog modules required to get the OV7670 camera working

    3 parts88

Similar boards

  • 2 layers126.5 × 126.5 mmDrip irrigation sys cc, the printed circuit board in 3D

    Drip irrigation sys cc

    hidroel/staj-2024

    Hidro Elektronik 2024 yaz dönemi staj çalışması

    108 parts
  • 4 layers101.9 × 90.8 mmCM5IO, the printed circuit board in 3D

    CM5IO

    jakemwood/alas

    Open source streaming appliance

    72 parts
  • 2 layers20.5 × 24.8 mmPi interface, the printed circuit board in 3D

    Pi interface

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    8 parts3.7k
  • 2 layers59.9 × 25.7 mmBuffer, the printed circuit board in 3D

    Buffer

    hoglet67/RGBtoHDMI

    Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

    8 parts1kGPL-3.0
  • 2 layers52 × 12.6 mmUSB, the printed circuit board in 3D

    USB

    shanteacontrols/OpenDeck

    A platform for building interactive control and sensing devices using MIDI and OSC built with Zephyr RTOS.

    8 parts960Apache-2.0
  • 2 layers87.5 × 48.5 mm7 input macropad, the printed circuit board in 3D

    7 input macropad

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    8 parts915

Questions

How big is the OV7670 breakout PCB?

It measures 25 × 43 mm and has 2 copper layers, 1.6 mm thick.

What parts does the OV7670 breakout use?

8 parts, built around the DALC208SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the OV7670 breakout KiCad files?

From the westonb/OV7670-Verilog repository on GitHub, at the commit this page was made from: the board is breakout/OV7670_breakout.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the OV7670 breakout design in my own project?

Its repository states no licence, so its author keeps all rights: ask westonb before reusing the design.