Skip to the content
2 layers103.7 × 65 mmLisalite, the printed circuit board in 3D

This is a reproduction of the Lisa Lite adapter card used to integrate Sony/Macintosh 400K 3.5" floppy drives into an Apple Lisa (in place of a Twiggy).

Size
103.7 × 65 mm
Copper layers
2
Thickness
1.6 mm
Parts
18
Nets
52
Pads
150
Tracks, vias
321, 9
Pours
6
Routed
Yes
KiCad
KiCad 7 (file 20221018)
Created
12 Dec 2023
Updated
20 Oct 2025

Overview

Lisalite is an open-source printed circuit board by warmech, from the warmech/lisa-lisalite repository on GitHub. It is a 2-layer board of 103.7 × 65 mm with 18 parts on 52 nets, routed with 321 tracks and 9 vias.

It is built around the 74LS85DC, 74LS393P-E and 74LS74PC. Its parts include 7 capacitors, 6 ICs, 2 connectors and 1 resistor. It belongs with the interfaces and adapters boards of this library.

Main components

3

README

README.md

Lisa Lite

The Lisa Lite is an adapter card for the Lisa 2 and 2/5 that allows a Twiggy drive to be replaced by a 400K Sony 3.5" floppy drive. Most of the signals are passed directly from the Twiggy interface to the Sony interface, though the motor clock signal on the Twiggy side is used as the basis (along with a 5MHz oscillator) for generating the PWM signal used to drive the Sony drive.

Lisa Lite Front

Lisa Lite Rear

Assembly

There is little to explain in terms of assembly, as the card uses relative few components. It should be noted that it is recommended to use keyed connectors for the Twiggy and Sony ribbon cable connectors. Inserting the cables backwards will result in the +12V power rail being piped into the CA0, CA1, CA2, and LSTRB lines on the Sony drive and the READ and MTRCLK lines on the Twiggy interface; this will likely destroy any ICs on these lines and possibly other passive and/or electromechanical components.

Use

There is also little to explain in terms of installation and use. The Lisa Lite fastens into two standoffs on the side of the internal drive cage closest to the monitor. The wide Twiggy ribbon cable connects to the interface at the rear of the card and the narrow ribbon cable to the interface in the card's middle. A socket may be used for the oscillator if desired, though it's not necessary by any means.

Once the card is installed and connected, no further action is required for use; the card is effectively a passive component itself and the Lisa ROM/IWM manages interfacing with the Sony drive.

Miscellany

This card is unnecessary on a 2/10, which uses an IC on the I/O card to handle communications with a Sony drive. Additionally, an 800K drive may be used in conjunction with a Sun Remarketing ROM intended for use with the Macintosh XL.

This is a very simple design that I would like to eventually replace with a small CPLD for use in an ATX form-factor Lisa. As it's so tiny a circuit, the Verilog required for this practically writes itself.

Parts

18
QtyValueFootprintReferences
60.1uF 50V Capacitor_THT:C_Axial_L3.8mm_D2.6mm_P10.00mm_HorizontalC1, C2, C3, C4, C5, C6
274LS85Package_DIP:DIP-16_W7.62mmU4, U5
2LOGOLOGOG***, G***
110uF 16VCapacitor_THT:CP_Axial_L10.0mm_D6.0mm_P15.00mm_HorizontalC7
13.3KResistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_HorizontalR1
15MHz XTALPackage_DIP:DIP-14_W7.62mmU1
174LS164Package_DIP:DIP-14_W7.62mmU6
174LS393Package_DIP:DIP-14_W7.62mmU3
174LS74Package_DIP:DIP-14_W7.62mmU2
1LisaLite FDD ConnectorConnector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_VerticalJ1
1LisaLite Twiggy Port ConnectorConnector_PinHeader_2.54mm:PinHeader_2x13_P2.54mm_VerticalJ2

Similar boards

  • 2 layers486 × 306.3 mmMonacoGP, the printed circuit board in 3D

    MonacoGP

    stonedDiscord/MonacoGP

    Sega MonacoGP TTL Boards

    257 parts1
  • 2 layers630 × 300 mmSecretBase, the printed circuit board in 3D

    SecretBase

    stonedDiscord/SecretBase

    SEGA Secret Base Arcade Game

    441 parts
  • 2 layers229.9 × 83.8 mm4b computer rev1, the printed circuit board in 3D

    4b computer rev1

    ethanjamesauto/modular_8bit_computer

    35 parts2
  • 2 layers365.1 × 203.2 mmDIAG, the printed circuit board in 3D

    DIAG

    Nakazoto/CenturionComputer

    This is just a simple backup of all the files related to the Centurion that I have stored on my HD. The Wiki itself has far more in-depth information about the Centurion and it's individual cards.

    150 parts172
  • 4 layers203.2 × 105.4 mmIBMExtender, the printed circuit board in 3D

    IBMExtender

    schlae/ibm-extender

    IBM 5161 expansion chassis extender and receiver cards

    44 parts33
  • 2 layersVortex f1-d clone, the printed circuit board in 3D

    Vortex f1-d clone

    hanshuebner/cpc-floppy-controllers

    MOVED to code.netzhansa.com/hanshuebner/cpc-floppy-controllers. This GitHub mirror is archived.

    60 parts7
  • 2 layersDS-88, the printed circuit board in 3D

    DS-88

    schlae/DS-88

    DS-88 Digisector PC Video Frame Grabber

    102 parts4CERN-OHL-P-2.0
  • 2 layers228.6 × 139.7 mm80cvc, the printed circuit board in 3D

    80cvc

    reifsnyderb/Atari-1090XL-80CVC

    Re-make of the Atari 1090XL 80 column card for monochrome monitors.

    78 parts3GPL-2.0

Questions

How big is the Lisalite PCB?

It measures 103.7 × 65 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Lisalite use?

18 parts, built around the 74LS85DC, 74LS393P-E and 74LS74PC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Lisalite KiCad files?

From the warmech/lisa-lisalite repository on GitHub, at the commit this page was made from: the board is cad/lisalite.kicad_pcb and its schematic cad/lisalite.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Lisalite design in my own project?

Its repository states no licence, so its author keeps all rights: ask warmech before reusing the design.