Skip to the content
2 layers99 × 70 mmRotator Controller V4, the printed circuit board in 3D

Rotator Controller V4

wa1hco/rotator_controller

Clean slate rebuild of full featured rotator controller.

Size
99 × 70 mm
Copper layers
2
Thickness
1.6 mm
Parts
94
Nets
112
Pads
315
Tracks, vias
309, 36
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
11 Oct 2026
Updated
21 Oct 2026

Overview

Rotator Controller V4 is an open-source printed circuit board by wa1hco, from the wa1hco/rotator_controller repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 99 × 70 mm with 94 parts on 112 nets, routed with 309 tracks and 36 vias.

It is built around the CPC1966B, ADUM3160BRW and AP2112K-3.3, with the NDP6802SF-50, SMAJ90CA and MM3Z3V6 among its other parts. Its parts include 34 capacitors, 26 resistors, 17 diodes, 7 ICs and 3 connectors. It belongs with the STM32 boards of this library.

Main components

8

README

hardware/controller-f407/README.md

F407 controller schematic

This is the new controller, started from the outside in. The rotor interface and the AC motor drive are on rotor_drive. The Drive MCU and the analog front end are the next two sheets.

The directory is hardware/controller-f407/ because ADR 0014 names the STM32F407, and the tree sits beside the imported V4 project at hardware/controller/ without mixing files. Leave hardware/controller/ untouched. It is the reference for the V4 TVS, snubber, and connector practice.

FileWhat it is
controller-f407.kicad_schRoot sheet. rotor_drive, drive_mcu, and analog_input hang off it. +5V and AC_FUSED stay no-connects until the power sheet exists.
rotor_drive.kicad_schAzimuth rotor connector, motor caps, triac drive, ARM relay, 26 VAC tap.
drive_mcu.kicad_schDrive MCU, STM32G431RBT6. Power, SWD, and the UART to the Station.
analog_input.kicad_schPot front end, the VIN_RECT warning, and the ADC reference filter.
rotor-drive.pdfPlot of both sheets, for review away from KiCad.
DESIGN-NOTES.mdWhat each block does, the calculations, the bill of materials, and the open questions.
symbols/controller-f407.kicad_symUnused TPS3823-33 symbol (the supervisor is not on the rotor sheet) and the no-pad Powerpole gland marker.
footprints/controller-f407.pretty/The two motor-cap footprints copied from the Hammond outline, and the gland marker.

KiCad 9. Nets leave rotor_drive on hierarchical labels (AZ_CW_EN, AZ_CCW_EN, AZ_BRAKE_EN, ARM_EN, ZC_SENSE, and the rest listed in the design notes). The pin assignment is in the Drive note. Through-hole parts are bought from Mouser. SMT parts that have a checked LCSC number say so on the symbol; the rest are TBD.

Elevation is a later copy of this sheet (ADR 0008), not a second channel here.

Parts

94
QtyValueFootprintReferences
80.1 2%Capacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC20, C21, C22, C23, C24, C25, C27, C28
81KResistor_SMD:R_0603_1608MetricR7, R11, R13, R14, R15, R16, R22, R23
627K 1%Resistor_SMD:R_0603_1608MetricR9, R10, R18, R19, R20, R21
510uCapacitor_SMD:C_0603_1608MetricC5, C12, C15, C17, C33
51uCapacitor_SMD:C_0603_1608MetricC8, C11, C14, C16, C34
4.1uCapacitor_SMD:C_0603_1608MetricC2, C4, C7, C9
4SMAJ90CADiode_SMD:D_SMAD12, D13, D14, D15
30.1 200VCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC29, C31, C32
3CPC1966RotatorController:CPC1966U3, U4, U5
20.1uCapacitor_SMD:C_0603_1608MetricC6, C18
210KResistor_SMD:R_0603_1608MetricR8, R26
21K5Resistor_SMD:R_0603_1608MetricR3, R4
21uCapacitor_SMD:C_1206_3216Metric_Pad1.33x1.80mm_HandSolderC26, C30
220pCapacitor_SMD:C_0603_1608MetricC10, C13
227Resistor_SMD:R_0402_1005MetricR5, R6
2360Resistor_SMD:R_0603_1608MetricR24, R25
247pCapacitor_SMD:C_0603_1608MetricC1, C3
25K1Resistor_SMD:R_0603_1608MetricR1, R2
2CWNKK_BB15AH:SW_NKK_BB15AHSW1, SW2
2FerriteBead_SmallInductor_SMD:L_0805_2012MetricFB1, FB2
2MM3Z3V6Diode_SMD:D_SOD-323D1, D2
2SMAJ10CADiode_SMD:D_SMAD16, D17
1120u 100VCapacitor_SMD:CP_Elec_8x10C19
112MCrystal:Crystal_SMD_2016-4Pin_2.0x1.6mmY1
11N4004Diode_SMD:D_SOD-123FD7
11kResistor_SMD:R_0603_1608MetricR12
126VACLED_SMD:LED_0402_1005MetricD11
12BZX84C3V6Package_TO_SOT_SMD:SOT-23D6
14K7Resistor_SMD:R_0603_1608MetricR17
15V_GRNLED_SMD:LED_0402_1005MetricD4
1ADUM3160Package_SO:SOIC-16W_7.5x10.3mm_P1.27mmU1
1AP2112K-3.3Package_TO_SOT_SMD:SOT-23-5U7
1Az_PresetPotentiometer_THT:Potentiometer_Alps_RK09K_Single_HorizontalRV1
1BrakeLED_SMD:LED_0402_1005MetricD10
1LeftLED_SMD:LED_0402_1005MetricD8
1MotorLED_SMD:LED_0402_1005MetricD3
1Motor CapConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_VerticalJ2
1NDP6802SF-50Package_TO_SOT_SMD:SOT-89-3U6
1RightLED_SMD:LED_0402_1005MetricD9
1RotatorConnector_TE-Connectivity:TE_MATE-N-LOK_1-770971-x_2x05_P4.14mm_HorizontalJ3
1STM32F405RGTxPackage_QFP:LQFP-64_10x10mm_P0.5mmU2
1USB-C 2.0 16PConnector_USB:USB_C_Receptacle_G-Switch_GT-USB-7010ASVJ1
1WhiteLED_SMD:LED_0402_1005MetricD5
1~Lightpipe:LP4-EPO1

More from wa1hco/rotator_controller

1
  • 2 layers159 × 99 mmController f407, the printed circuit board in 3D

    Controller f407

    wa1hco/rotator_controller

    Clean slate rebuild of full featured rotator controller.

    122 partsGPL-3.0

Similar boards

  • 2 layers100 × 100 mmBirdNestV3, the printed circuit board in 3D

    BirdNestV3

    VorosEgyes/BirdNest

    BirdNest Camera

    68 parts1MIT
  • 2 layers120 × 92 mmRotatorController, the printed circuit board in 3D

    RotatorController

    wa1hco/Rotator-Controller-V2

    Designed to remotely control CDE rotors. Updated design with new enclosure and optional user interface

    60 partsCC0-1.0
  • 2 layers148.3 × 108.4 mmRJ Schematic v1.0, the printed circuit board in 3D

    RJ Schematic v1.0

    Jscott44/RTEP5-the-raspberry-jam

    Realtime digital guitar effects pedal designed for Raspberry PI, written in C++

    121 parts13MIT
  • 4 layers233.4 × 147.3 mmOpenPLC Hardware, the printed circuit board in 3D

    OpenPLC Hardware

    gasiepgodoy/Open-Source-PLC

    Open Source Programmable Logic Controller (Hardware and Software). Based on the Master of Science in Electrical Engineering of João Vitor Rocha Santana

    494 parts2
  • 2 layers100 × 55 mmWellD, the printed circuit board in 3D

    WellD

    kinggh0stee/WellD

    ESP32-C6 Zigbee well monitor — reads a 4–20 mA pressure transducer and DS18B20, reports water level, temperature, and battery to Zigbee2MQTT with OTA update support

    122 parts2MIT
  • 4 layers101 × 51.5 mmQuack core, the printed circuit board in 3D

    Quack core

    HeyPCB/quack-core

    Brain board for the Open Duck Mini: Pi Zero 2W carrier, 14-servo STS bus, fused 2S power path in stitched copper zones (15-18 A battery side), USB-C charging with balancing, IMU.

    138 parts1CERN-OHL-S-2.0
  • 4 layers50 × 52 mmSky130 nfc daughter, the printed circuit board in 3D

    Sky130 nfc daughter

    morzack/ece592-nfc-caravan-pcbs

    Design files for breakout and motherboard PCBs for Sky130 NFC chip designed in NCSU's Tapeout Course (spr2025)

    253 parts1
  • 2 layers80 × 80 mmPiezzo, the printed circuit board in 3D

    Piezzo

    ilkercosar/Hardware-Desing

    48 parts

Questions

How big is the Rotator Controller V4 PCB?

It measures 99 × 70 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Rotator Controller V4 use?

94 parts, built around the CPC1966B, ADUM3160BRW, AP2112K-3.3 and NDP6802SF-50. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Rotator Controller V4 KiCad files?

From the wa1hco/rotator_controller repository on GitHub, at the commit this page was made from: the board is hardware/controller/Rotator-Controller-V4.kicad_pcb and its schematic hardware/controller-f407/analog_input.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Rotator Controller V4 design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).