2 layers
2 layers50 × 50 mm
Pinecone V1
vmshade/Pinecone- Size
- 50 × 50 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 46
- Nets
- 59
- Pads
- 223
- Tracks, vias
- 439, 36
- Pours
- 1
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 11 Oct 2026
- Updated
- 11 Oct 2026
Overview
Pinecone V1 is an open-source printed circuit board by vmshade, from the vmshade/Pinecone repository on GitHub. It is a 2-layer board of 50 × 50 mm with 46 parts on 59 nets, routed with 439 tracks and 36 vias.
It is built around the RP2040, W25Q128JVPIQ and TLV75533PDRV, with the USBLC6-2SC6 and M2.5 among its other parts. Its parts include 18 capacitors, 9 resistors, 4 ICs, 4 connectors and 2 diodes. It belongs with the RP2040 boards of this library.
Main components
5
RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)
W25Q128JVPIQ
WSON-8-EP(5x6)-40℃~+85℃ 100,000 cycles 10uA 120ms@(32KB) 128Mbit 133MHz 2.7V~3.6V 20 Years Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection、Power lock protection SPI WSON-8-EP(5x6) NOR FLASH ROHSWinbond ElecNOR FLASH
TLV75533PDRV
WSON-6-EP(2x2)-40℃~+125℃@(Tj) 1 238mV@(500mA) 25uA 3.3V 46dB@(100kHz) 5.5V 500mA 71.5uVrms Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown、Enable control、Input under-voltage protection、Output discharge、Built-in soft-start Positive WSON-6-EP(2x2) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) Regulators
USBLC6-2SC6
SOT-23-60.35pF、0.8pF 100nA 150W@8/20us 15V 2 5V 6A@8/20us 6V ESD SOT-23-6 ESD and Surge Protection (TVS/ESD) ROHSUMWESD And Surge Protection (TVS/ESD)M2.5
-0.45mm 2.5mm 2mm 5mm DIN934 Hex M2.5X0.45 Nickel plated Silver white - Hexagonal nutsShuntianHex Nut
README
README.mdPinecone - An RP2040 powered dev board
What is it?
Pinecone is an RP2040 powered dev board, inspired by the legendary Arduino Uno line-up. It features things like a USB-C port which the Unos simply lack.
Why?
I created this to jump-start and expand my hobby in electronics by designing and hopefully manufacturing my first PCB. I also previously used the Uno R3, and thought there are alot of things i could do to improve it, while making it smaller.
Here are some cool features Pinecone has
- RP2040
- 16MB of fast, QSPI Flash
- USB-C
- 29 GPIOs broken out into easy to use sockets
- Neopixel
- Power-On LED
- ESD and Voltage spike protection
- Small, 5cm x 5cm pcb size
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | 0.1µF | Capacitor_SMD:C_0402_1005Metric | C2, C3, C4, C5, C6, C7, C8, C9, C11, C12, C17, C20 |
| 4 | M2.5 | MountingHole:MountingHole_2.7mm_M2.5_Pad | H1, H2, H3, H4 |
| 2 | 10kΩ | Resistor_SMD:R_0402_1005Metric | R7, R8 |
| 2 | 10µF | Capacitor_SMD:C_0603_1608Metric | C13, C14 |
| 2 | 15pF | Capacitor_SMD:C_0402_1005Metric | C15, C16 |
| 2 | 1kΩ | Resistor_SMD:R_0402_1005Metric | R5, R6 |
| 2 | 1µF | Capacitor_SMD:C_0402_1005Metric | C1, C10 |
| 2 | 27Ω | Resistor_SMD:R_0402_1005Metric | R3, R4 |
| 2 | 5.1kΩ | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | Right | Library:PinSocket_1x12_P2.54mm_Vertical_F | J4, J5 |
| 1 | 12Mhz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | 680kΩ | Resistor_SMD:R_0402_1005Metric | R10 |
| 1 | 750mA | Fuse:Fuse_1206_3216Metric | F1 |
| 1 | BOOT | Button_Switch_THT:SW_PUSH_6mm | Boot |
| 1 | LED | LED_SMD:LED_0805_2012Metric | D3 |
| 1 | LOGO | LOGO | G*** |
| 1 | Left | Library:PinSocket_1x12_P2.54mm_Vertical | J3 |
| 1 | RESET | Button_Switch_THT:SW_PUSH_6mm | Reset |
| 1 | RP2040 | Package_DFN_QFN:QFN-56-1EP_7x7mm_P0.4mm_EP3.2x3.2mm | U5 |
| 1 | SMF5V0A | Diode_SMD:D_SMF | D1 |
| 1 | TLV75533PDRV | Package_SON:WSON-6-1EP_2x2mm_P0.65mm_EP1x1.6mm | U1 |
| 1 | USB-C | Connector_USB:USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J2 |
| 1 | USBLC6-2SC6 | Package_TO_SOT_SMD:SOT-23-6 | U4 |
| 1 | W25Q128JVPIQ | Package_SON:WSON-8-1EP_6x5mm_P1.27mm_EP3.4x4.3mm | U3 |
Questions
How big is the Pinecone V1 PCB?
It measures 50 × 50 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Pinecone V1 use?
46 parts, built around the RP2040, W25Q128JVPIQ, TLV75533PDRV and USBLC6-2SC6. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Pinecone V1 KiCad files?
From the vmshade/Pinecone repository on GitHub, at the commit this page was made from: the board is Pinecone V1/Pinecone V1.kicad_pcb and its schematic Pinecone V1/Pinecone V1.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Pinecone V1 design in my own project?
Its repository states no licence, so its author keeps all rights: ask vmshade before reusing the design.
Similar boards
- 2 layers290.1 × 130 mm
- 2 layers100 × 68 mm
AICHO
ayuusweetfish/AICHO
(✔️ Docs to-do) 《同呼吸：生灵和鸣》互动装置 · Interactive installation on machines' lifelike reactions to life · 2024 全国美展
124 parts - 2 layers160 × 60 mm
- 2 layers228.6 × 80.7 mm
Open keyboard
PanosEconomou/open-keyboard
A 100% from scratch open source super cool awesome keyboard that will take years to make if ever
136 parts - 4 layers65 × 20 mm
- 4 layers90 × 70 mm
Bypass clean before shorter-22
JesseLevine727/AirNote
A touchless musical instrument built around a fully integrated RP2040, VL53L1X distance sensor and MAX98357A speaker amplifier. One hand selects eleven pentatonic notes over two octaves.
73 parts - 4 layers95 × 95 mm
AgentDeck
Brillar0101/agentdeck
RP2040 macropad for supervising AI coding agents: 13 hot-swap keys with per-key RGB status, encoder, joystick, 4-layer PCB, CircuitPython firmware, printable enclosure
101 partsMIT