Skip to the content
4 layers30 × 30 mmPCIe Pie, the printed circuit board in 3D

KiCad design for an M.2 Key A RP2350B sensor module featuring an MPU-9250 IMU and BME280, intended for UAV and ArduPilot integration experiments.

Size
30 × 30 mm
Copper layers
4
Thickness
2 mm
Parts
85
Nets
131
Pads
382
Tracks, vias
94, 8
Pours
9
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
8 Oct 2026
Updated
10 Oct 2026

Overview

PCIe Pie is an open-source printed circuit board by vk-sahni, from the vk-sahni/M.2_IMU_sensor_module repository on GitHub. It is a 4-layer board of 30 × 30 mm with 85 parts on 131 nets, routed with 94 tracks and 8 vias.

It is built around the RP2350B, BME280 and W25Q128JVSIQ, with the XC6220B331PR-G, APS6404L-3SQR-SN and MPU-9250 among its other parts. Its parts include 42 capacitors, 14 resistors, 8 ICs, 5 inductors and 3 diodes. It belongs with the computers and single-board computers and sensors and measurement boards and the RP2350 boards of this library.

Main components

8

README

readme.md

M.2 RP2350 IMU Sensor Module

A KiCad hardware design for a compact M.2 Key A sensor module built around the Raspberry Pi RP2350B. The board combines an MPU-9250 motion sensor and a BME280 environmental sensor, with UAV and ArduPilot integration as the intended use case.

Project status: Work in progress. The repository contains KiCad design files only; it does not include firmware or establish plug-and-play ArduPilot compatibility. The current design has outstanding KiCad ERC/DRC violations and is not ready for fabrication or flight use.

GitHub repository description

KiCad design for an M.2 Key A RP2350B sensor module featuring an MPU-9250 IMU and BME280, intended for UAV and ArduPilot integration experiments.

Design overview

  • MCU: RP2350B
  • IMU: MPU-9250 (accelerometer, gyroscope, and magnetometer)
  • Environmental sensor: BME280 (pressure, temperature, and humidity)
  • Memory: W25Q128JVSIQ QSPI flash and APS6404L PSRAM
  • Removable storage: MicroSD card socket
  • Host connection: M.2 Key A edge connector
  • Other interfaces: USB Type-C, SWD test points, and status LEDs
  • Power: On-board XC6220 3.3 V regulators

The M.2 connector schematic maps 5 V power and sensor I2C signals, including separate SDA/SCL and MPU_SDA/MPU_SCL nets. Check the full schematic and target host pinout before connecting the module; M.2 is a connector format, not a guarantee of electrical or firmware compatibility.

ArduPilot integration

This is a hardware design intended for UAV sensor and ArduPilot integration experiments. ArduPilot supports sensor communications over protocols such as I2C, SPI, UART, and CAN, but a sensor board still needs a compatible driver/backend, wiring, and configuration. This repository does not contain that firmware integration or demonstrate that an ArduPilot flight controller can detect these sensors through this M.2 connection.

Before attempting integration, verify the M.2 host pinout and voltage levels, determine which controller owns each bus, and confirm that the target ArduPilot firmware supports the required sensors and connection arrangement. See the official ArduPilot sensor-driver documentation.

Repository contents

  • PCIe_Pie.kicad_pro — KiCad project settings
  • PCIe_Pie.kicad_sch and the other *.kicad_sch files — top-level and hierarchical schematics
  • PCIe_Pie.kicad_pcb — PCB layout
  • CM4IO.pretty/ — project footprint library
  • CM4IO.3dshapes/ — 3D models used by footprints
  • sym-lib-table, fp-lib-table — KiCad library table configuration

Open the design

  1. Install KiCad.
  2. Open PCIe_Pie.kicad_pro.
  3. Review the complete schematic hierarchy and PCB, including the project-local footprint and 3D model libraries.

Validation status

KiCad command-line ERC and DRC checks run against the current design reported outstanding violations, including unconnected items. Review and resolve these in KiCad before generating manufacturing files. No fabrication outputs, assembled-board test results, sensor calibration results, or flight-test results are included in this repository.

Safety

Treat the design as experimental. Verify the schematic, PCB rules, power rails, connector orientation, and signal levels before powering hardware. Bench-test and validate the complete sensor/firmware path before any UAV flight; do not rely on this module as a flight-critical sensor without appropriate testing and failsafes.

References

Parts

85
QtyValueFootprintReferences
200.1uFCapacitor_SMD:C_0402_1005MetricC2, C5, C10, C11, C12, C13, C14, C17, C22, C24, C25, C26, C33, C34, C36, C40 +4
74.7uFCapacitor_SMD:C_0402_1005MetricC3, C15, C16, C18, C19, C37, C41
610uFCapacitor_SMD:C_0402_1005MetricC4, C29, C30, C31, C38, C42
51KResistor_SMD:R_0402_1005MetricR3, R4, R12, R13, R14
44.7KResistor_SMD:R_0402_1005MetricR8, R9, R10, R11
310uFCapacitor_SMD:C_0805_2012MetricC1, C35, C39
3FERRITE BEAD 600 OHM 0805 1LNInductor_SMD:L_0402_1005MetricL1, L4, L5
3LEDLED_SMD:LED_0402_1005MetricD1, D2, D3
3XC6220B331PR-GXC6220B331PR-G:SOT-89-5_TORU1, U8, U9
215pFCapacitor_SMD:C_0402_1005MetricC20, C21
222uFCapacitor_SMD:C_0402_1005MetricC27, C28
227RResistor_SMD:R_0402_1005MetricR6, R7
2PESD5V0S1BBPESD5V0S1BB:SOD523_NXP-LCR2, CR3
2TS2.8X4.2SMT-H1.9Button_Switch_SMD:SW_Push_SPST_NO_Alps_SKRKSW1, SW2
10RResistor_SMD:R_0402_1005MetricR2
11051620001SD-CARD:105162-0001_MOLJ3
110KResistor_SMD:R_0402_1005MetricR5
110nFCapacitor_SMD:C_0402_1005MetricC32
12.2uFCapacitor_SMD:C_0402_1005MetricC23
133RResistor_SMD:R_0402_1005MetricR1
1ABM8-272-T3ABM8-272-T3:ABM8-272-T3_ABRX1
1APS6404L-3SQR-SNAPS6404L-3SQR-SN:APS6404L-3SQR-SN_APY-MU4
1BLM18HE601SN1DInductor_SMD:L_0402_1005MetricL2
1BME280Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumberingU5
1Bus_M.2_Socket_AConnector_PCBEdge:M.2_3030-xx-AJ2
1FIXED IND 3.3UH 1.8A 135 MOHMInductor_SMD:L_0402_1005MetricL3
1MBRM140T1GMBRM140T1G:CR_POWERMITE_457-04_ONS-LCR1
1MPU-9250Sensor_Motion:InvenSense_QFN-24_3x3mm_P0.4mmU6
1RP2350BPackage_DFN_QFN:QFN-80-1EP_10x10mm_P0.4mm_EP3.4x3.4mmU2
1SWCLKTestPoint:TestPoint_Pad_1.0x1.0mmTP1
1SWDTestPoint:TestPoint_Pad_1.0x1.0mmTP2
1USB_DM_PTestPoint:TestPoint_Pad_1.0x1.0mmTP3
1USB_DP_PTestPoint:TestPoint_Pad_1.0x1.0mmTP4
1VBUS_USBTestPoint:TestPoint_Pad_1.0x1.0mmTP5
1W25Q128JVSIQW25Q128JVSIQ:SOIC_128JVSIQ_WIN-MU3

Similar boards

  • 4 layers93 × 155.6 mmRocky ctrl, the printed circuit board in 3D

    Rocky ctrl

    PotatoPeaSea/Rocky

    Five-legged walking robot inspired by Rocky (Project Hail Mary).

    173 parts
  • 4 layers132.8 × 75.8 mmAudioPicoBare, the printed circuit board in 3D

    AudioPicoBare

    elrir01/AudioPico

    This board receive audio from a BT source like a phone and outputs via a DAC the audio. It's an old project of mine but I've decided to publish it just now, so the full description is not ready and will be updated in…

    84 partsGPL-3.0
  • 2 layers100 × 89.5 mmLed processor board, the printed circuit board in 3D

    Led processor board

    eelstretching/led-processor-board

    A board with a processor and a couple of other things that can talk to an LED output board.

    128 parts
  • 2 layers52 × 89.5 mmRP2350B RM2, the printed circuit board in 3D

    RP2350B RM2

    eelstretching/rp2350b-rm2-reference

    Raspberry Pi's RP2350B minimal design (RPI-RP2350B-MINIMAL R4-S1, KiCad 10) with these additions:

    57 parts
  • 6 layers160 × 100 mmHet68-core, the printed circuit board in 3D

    Het68-core

    fedurca/het68_pcb

    pcb design description

    134 parts
  • 4 layers70 × 97 mmStopwatchy, the printed circuit board in 3D

    Stopwatchy

    JEAPI-DEV/Project_Penta

    82 partsGPL-3.0
  • 2 layers30.5 × 68.6 mm16bit-5v, the printed circuit board in 3D

    16bit-5v

    bread-modular/bread-modular

    Modular Synths for Everyone

    62 parts67MIT
  • 4 layers50 × 70 mmRp569, the printed circuit board in 3D

    Rp569

    kelu124/rp569

    RP569 - PIOs to usb3 ( rp2350 x ch569 )

    146 parts3

Questions

How big is the PCIe Pie PCB?

It measures 30 × 30 mm and has 4 copper layers, 2 mm thick.

What parts does the PCIe Pie use?

85 parts, built around the RP2350B, BME280, W25Q128JVSIQ and XC6220B331PR-G. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PCIe Pie KiCad files?

From the vk-sahni/M.2_IMU_sensor_module repository on GitHub, at the commit this page was made from: the board is PCIe_Pie.kicad_pcb and its schematic BME280.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the PCIe Pie design in my own project?

Its repository states no licence, so its author keeps all rights: ask vk-sahni before reusing the design.