
Clean room
trieuhuyduc/Clean_room_slave
ESP32-based slave controller board for cleanroom equipment — RS485/Modbus, isolated I/O, 220V mains control (KiCad)

atm90e26 reference board for kick start
ATM90E26 EVAL is an open-source printed circuit board by vivmchp, from the vivmchp/atm90e26_ref repository on GitHub. It is a 2-layer board of 80 × 70 mm with 43 parts on 30 nets, routed with 419 tracks and 17 vias.
It is built around the HLK-10M12, ATM90E26-YU and MIC5209-3.3YS-TR, with the 10D561K and ZMPT101K among its other parts. Its parts include 17 capacitors, 13 resistors, 5 connectors, 4 ICs and 1 crystal.
KiCad 10.0 design for a single-phase energy metering evaluation board based on the Microchip ATM90E26A IC.
| Front | Back |
|---|---|
![]() | ![]() |
| Pin | Signal | Description |
|---|---|---|
| 1 | LINE | AC Live (100-240VAC) |
| 2 | NEUT | AC Neutral |
| Pin | Signal | Description |
|---|---|---|
| 1 | I1P | Current channel positive |
| 2 | I1N | Current channel negative |
| Pin | Signal | Description |
|---|---|---|
| 1 | +3.3V | 3.3V power output |
| 2 | GND | Ground |
| 3 | ATM_SDI | SPI data in (MOSI to ATM90E26) |
| 4 | ATM_SDO | SPI data out (MISO from ATM90E26) |
| 5 | ATM_CLK | SPI clock |
| 6 | ATM_CS | Chip select (active low) |
| 7 | ATM_IRQ | Interrupt output |
| 8 | ATM_CF1 | Energy pulse output |
| 9 | SCL | I2C clock (1K pull-up) |
| 10 | SDA | I2C data (1K pull-up) |
| Parameter | Value |
|---|---|
| Board size | 80mm × 70mm |
| Layers | 2 (Top + Bottom copper) |
| Thickness | 1.6mm |
| Default track | 0.2mm |
| Default via | 0.6mm / 0.3mm drill |
| HV track | 1.0mm |
| HV clearance | 1.0mm |
| Ref | Part | Value | Package |
|---|---|---|---|
| U1 | HLK-10M12 | 12V/10W | Module |
| U2 | ATM90E26-YU | - | SSOP-28 |
| U3 | MIC5209-3.3YS-TR | 3.3V | SOT-223 |
| U4 | 24C02C | 2Kbit | SOIC-8 |
| TR1 | ZMPT101K | 1000:1000 | Through-hole |
| Y1 | Crystal | 8.192MHz | HC49-U |
| RV1 | Varistor | 10D561 | Disc |
| R1 | Resistor | 200K/3W | Axial |
| C13, C14 | Capacitor | 12pF | 0603 |
Gerber files for PCB fabrication are in ATM90E26_EVAL/output/:
| File | Description |
|---|---|
| *-F_Cu.gbr | Front copper layer |
| *-B_Cu.gbr | Back copper layer |
| *-F_Mask.gbr | Front solder mask |
| *-B_Mask.gbr | Back solder mask |
| *-F_Paste.gbr | Front solder paste |
| *-B_Paste.gbr | Back solder paste |
| *-F_Silkscreen.gbr | Front silkscreen |
| *-B_Silkscreen.gbr | Back silkscreen |
| *-Edge_Cuts.gbr | Board outline |
| *-PTH.drl | Plated through holes |
| *-NPTH.drl | Non-plated holes |
Reference design for evaluation purposes.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C11, C12, C16, C17 |
| 4 | 1K | Resistor_SMD:R_0805_2012Metric | R4, R5, R9, R10 |
| 2 | 0.33uF | Capacitor_SMD:C_0603_1608Metric | C5, C6 |
| 2 | 1.8K | Resistor_SMD:R_0805_2012Metric | R12, R13 |
| 2 | 100E | Resistor_SMD:R_0805_2012Metric | R7, R8 |
| 2 | 12pF | Capacitor_SMD:C_0603_1608Metric | C13, C14 |
| 2 | 1KpF | Capacitor_SMD:C_0603_1608Metric | C7, C8 |
| 2 | 2.7E | Resistor_SMD:R_0805_2012Metric | R2, R3 |
| 2 | 4.7uF/10V | Capacitor_SMD:C_0805_2012Metric | C1, C9 |
| 1 | 0.033uF | Capacitor_SMD:C_0603_1608Metric | C3 |
| 1 | 0.1uF/275V | Capacitor_THT:C_Rect_L16.5mm_W10.9mm_P15.00mm_MKT | C4 |
| 1 | 0E | Resistor_SMD:R_0805_2012Metric | R11 |
| 1 | 10D561 | Varistor:RV_Disc_D12mm_W3.9mm_P7.5mm | RV1 |
| 1 | 10K | Resistor_SMD:R_0805_2012Metric | R6 |
| 1 | 12V Supply | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | 1uF/10V | Capacitor_SMD:C_0805_2012Metric | C2 |
| 1 | 200K/3W | Resistor_THT:R_Axial_DIN0918_L18.0mm_D9.0mm_P22.86mm_Horizontal | R1 |
| 1 | 22uF | Capacitor_Tantalum_SMD:CP_EIA-3528-12_Kemet-T | C15 |
| 1 | 22uF/25V | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C10 |
| 1 | 24C02Cx-x-SN | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | 3.3V Supply | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | 3.3VOLT | TestPoint:TestPoint_THTPad_D1.0mm_Drill0.5mm | TP1 |
| 1 | 8.192Mhz | Crystal:Crystal_HC49-U_Vertical | Y1 |
| 1 | AC INPUT | TerminalBlock_Philmore:TerminalBlock_Philmore_TB132_1x02_P5.00mm_Horizontal | J1 |
| 1 | ATM90E26-YU | Package_SO:SSOP-28_5.3x10.2mm_P0.65mm | U2 |
| 1 | Conn_01x10 | Connector_PinHeader_2.54mm:PinHeader_1x10_P2.54mm_Vertical | J5 |
| 1 | Current Input | TerminalBlock_Philmore:TerminalBlock_Philmore_TB132_1x02_P5.00mm_Horizontal | J2 |
| 1 | HLK-10M12 | Converter_ACDC:Converter_ACDC_Hi-Link_HLK-10Mxx | U1 |
| 1 | MIC5209-3.3YS-TR | Package_TO_SOT_SMD:SOT-223 | U3 |
| 1 | ZMPT101K | Transformer_THT:Transformer_Zeming_ZMPT101K | TR1 |

trieuhuyduc/Clean_room_slave
ESP32-based slave controller board for cleanroom equipment — RS485/Modbus, isolated I/O, 220V mains control (KiCad)

reivax-boucoi/PCB_Kicad
Repo for all my home projects involving PCBs developped with Kicad

whatnick/ATM90E26_Featherwing_KiCAD
ATM90E26 Featherwing with ongoing development in KiCAD

hicancan/carbentra-smart-plug
CARBENTRA smart plug: AIoT edge device for campus energy orchestration

jumarubea/OpenSmartMeter
Low-cost & OEM agnostic GSM prepaid smart energy meter with a customizable API.


FredM67/PVRouter-KiCad
Fichiers de conception KiCad pour le Mk2 PV Router — un système open-source de routage solaire photovoltaïque universel (monophasé, triphasé avec ou sans neutre, biphasé).

kehindejanetolaniyi23/home-automation-kicad-work-in-progress
Work-in-progress KiCad PCB design for a home automation relay and power monitoring board, including schematic review, PCB layout review, and DRC improvement notes.
It measures 80 × 70 mm and has 2 copper layers, 1.6 mm thick.
43 parts, built around the HLK-10M12, ATM90E26-YU, MIC5209-3.3YS-TR and 10D561K. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the vivmchp/atm90e26_ref repository on GitHub, at the commit this page was made from: the board is ATM90E26_EVAL/ATM90E26_EVAL/ATM90E26_EVAL.kicad_pcb and its schematic ATM90E26_EVAL/ATM90E26_EVAL/ATM90E26_EVAL.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask vivmchp before reusing the design.