
PCB ESP32-C3-DevKitC-02
vives-project-xp/EOMarkers
Develop small standalone boxes that light up when someone approaches them. The boxes can be fitted with a plexi with Electronics-ICT and a direction indication via an arrow.

Develop small standalone boxes that light up when someone approaches them. The boxes can be fitted with a plexi with Electronics-ICT and a direction indication via an arrow.
PCB ESP32-C3-DevKitM-1 is an open-source printed circuit board by vives-project-xp, from the vives-project-xp/EOMarkers repository on GitHub. It is a 2-layer board of 52.2 × 43.6 mm with 10 parts on 29 nets, routed with 47 tracks and 0 vias.
It is built around the ESP32-C3-DEVKITM-1. Its parts include 4 resistors, 2 diodes, 2 transistors, 1 IC and 1 connector. It belongs with the ESP32 and RISC-V boards of this library.
Develop small standalone boxes that light up when someone approaches them. The boxes can be fitted with a plexi with Electronics-ICT and a direction indication via an arrow.
.
├── 3d tekening
│ ├── 3D_Bottom.png
│ ├── 3D_Main.png
│ └── README.md
├── Affiche
│ └── EO Markers Affiche.png
├── AndroidStudio
│ ├── EO-Markers
│ │ └── app
│ └── README.md
├── Arduino
│ ├── EO-Markers
│ │ ├── EO-Markers.cpp
│ │ └── EXAMPLE-config.h
│ └── README.md
├── img
│ ├── qr.png
│ └── project_canvas.png
│ └── potentiometers.jpg
│ └── schakelaar.jpg
├── PCB
│ ├── PCB
| ├── PCB_ESP32-C3-DevKitM-1



more info: 3D Tekening
This is the base of the cube. The sensor is placed in the small round hole, the LED strips stick to the inside of the posts and the cables are inserted through the middle part. A reflective film has been applied to this area, which helps to spread the light around. A diffuser (plexiglass) is slid into the furthest slot and a plywood wall, with or without directions, is placed in the nearest slot.


This is the bottom of the cube. This is where the PCB, battery holder and cables end up. A hole is provided for a USB cable as secondary power. These 2 prints are screwed together with an M3 screw or bolt.

more info: Android Studio
more info: Arduino
more info: PCB
The PCB consists of a pair of connectors for the ESP, LED strip, sensor and USB-C port. These are female headers, so they fit in perfectly. The connectors are internally connected on the PCB.

The circuit consists of 1 ESP, powered by a USB cable or a 5V battery pack connected in parallel on the j1 connector with a diode from battery pack to connector (4 rechargeable AA batteries). 3 female headers for the LED strips, 3 female headers for the sensor, 8 female headers for the USB-C port and a diode to stop current to the batteries.
Measurements: U LED-strips (off): 4,1V; U LED-strips (on): 3,1V
U Batteries (leds off): 4.9V; U Batteries (leds on): 4.3V
U Diode (leds off): 0.72V; U Diode (leds on): 0.86V
U Sensor (leds off): 2.98V; U Sensor (leds on): 2.55V
U ESP (leds off): 4.1V; U ESP (leds on): 3.45V

| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 10KΩ | Resistor_SMD:R_0805_2012Metric | R2, R4 |
| 2 | 1KΩ | Resistor_SMD:R_0805_2012Metric | R1, R3 |
| 2 | Conn_01x03_Socket | Connector_PinSocket_2.54mm:PinSocket_1x03_P2.54mm_Vertical | LED1, Sensor1 |
| 2 | NPN | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 1 | Conn_01x08_Socket | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | J1 |
| 1 | ESP32-C3-DEVKITM-1 | ESP32-C3-DEVKITM-1:XCVR_ESP32-C3-DEVKITM-1 | U1 |

vives-project-xp/EOMarkers
Develop small standalone boxes that light up when someone approaches them. The boxes can be fitted with a plexi with Electronics-ICT and a direction indication via an arrow.

vives-project-xp/EOMarkers
Develop small standalone boxes that light up when someone approaches them. The boxes can be fitted with a plexi with Electronics-ICT and a direction indication via an arrow.

Ahmed-YSY/FleetGuard
IoT vehicle telematics for fleet & logistics — ESP32 + SIM7600G 4G/GPS tracker with fuel-theft detection, tamper/cargo security alarms, offline-resilient MQTT reporting, and OBD2 data over ESP-NOW.

iho77/ppo_v2
This work is licensed under a [Creative Commons Attribution-NonCommercial 4.0 International License][cc-by-nc].

TiboDevC/clockclock
Personal project of a kinetic clock inspired by Humans Since 1982, using 48 stepper motors to display time in an artistic and dynamic way.

Abineshpk007/KICAD-solar_panel_monitoring_prototype
This is my PCB, there are many outer like it but this is mine

diaxxu/CNC-Router
a challenge i gave myself to make something great ! yes its a cnc milling / laser / plotter machine

saniyafatima07/Hail_Mary
Lakshya: Low Cost Precision Guidance and Smart Electronic Fuze System


VladimirVladimirovMinkov/UOA_HPA
This is a code and document repository for the University of auckland Aeronaughtics Club Human Powered Aircraft
It measures 52.2 × 43.6 mm and has 2 copper layers, 1.6 mm thick.
10 parts, built around the ESP32-C3-DEVKITM-1. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the vives-project-xp/EOMarkers repository on GitHub, at the commit this page was made from: the board is PCB/PCB_ESP32-C3-DevKitM-1/PCB.kicad_pcb and its schematic PCB/PCB/PCB.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask vives-project-xp before reusing the design.