Skip to the content
2 layersHail Mary, the printed circuit board in 3D

Lakshya: Low Cost Precision Guidance and Smart Electronic Fuze System

Copper layers
2
Thickness
1.6 mm
Parts
11
Nets
28
Pads
72
Tracks, vias
136, 0
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
29 Aug 2026
Updated
29 Sep 2026

Overview

Hail Mary is an open-source printed circuit board by saniyafatima07, from the saniyafatima07/Hail_Mary repository on GitHub. It is a 2-layer board with 11 parts on 28 nets, routed with 136 tracks and 0 vias.

It is built around the ESP32-C3-DEVKITM-1 and BMP280. Its parts include 6 connectors, 2 switches, 1 resistor, 1 IC and 1 diode. It belongs with the ESP32 and RISC-V boards of this library.

Main components

2

README

README.md

Low Cost Precision Guidance and Smart Electronic Fuze System for a 155 mm Artillery Shell

A low cost Precision Guidance System Kit prototype designed as a modular electronics package that can be integrated with an existing 155 mm artillery shell form factor. The system combines inertial sensing, GNSS positioning, environmental monitoring, BLDC based actuation and multi mode event detection to demonstrate the architecture of a retrofit guidance and electronic fuze platform.

Demo Video

https://github.com/user-attachments/assets/235a1aa5-04df-45c1-bc84-9b7f6d06c8ea

Overview

The Low Cost Precision Guidance and Smart Electronic Fuze System is focused on integrating embedded sensing, navigation, actuation and a multi-mode electronic fuze architecture.

The system is designed around a modular embedded platform that combines inertial sensing, GNSS positioning, atmospheric monitoring, power telemetry, proximity detection, impact/event sensing, and BLDC based actuation.

The current V1 prototype uses an ESP32 as the primary embedded controller and integrates:

  • MPU6050: 6 axis inertial measurement
  • NEO-6M: GNSS positioning
  • BMP280: Barometric pressure and temperature
  • INA219: Voltage and current monitoring
  • IR Proximity Sensor: Proximity detection
  • SW-240: Impact/vibration event detection
  • BLDC Motor: Actuation mechanism for the prototype guidance subsystem

The system supports a Multi-Mode Smart Fuze architecture consisting of:

  • Proximity Mode
  • Time Mode
  • Impact Mode

The V1 platform is intended primarily for Testing, sensor integration, firmware development, simulation, telemetry, and proof of concept validation.


Project Objectives

The project aims to develop a compact and modular embedded platform capable of supporting:

  1. Inertial sensing
  2. GNSS positioning
  3. Environmental sensing
  4. Power monitoring
  5. Proximity detection
  6. Impact/event detection
  7. BLDC-based actuation
  8. Multi mode fuze state management
  9. Sensor fusion
  10. Real time telemetry

Prototype Hardware

ComponentFunctionInterface
ESP32Main microcontroller—
MPU60506 axis inertial measurementI2C
NEO-6MGNSS/GPS positioningUART
BMP280Barometric pressure and temperatureI2C
INA219Voltage and current monitoringI2C
IR SensorProximity detectionGPIO
SW-240Impact/vibration detectionGPIO
BLDC MotorPrototype actuationMotor Driver / PWM

Simulation Stack

The simulation is a three-layer chain, from pure physics to the real embedded
controller. Each layer validates the one above it, and every equation is
traceable to published exterior-ballistics literature (McCoy Modern Exterior
Ballistics
, Raza & Wang 2022, Cheng 2019, Chusilp 2012, Glebocki 2022).

text
+---------------------------------------------------------------+                                                                                                                        
|  LAYER 1 — 3-DOF FLIGHT PHYSICS (truth model)                 |                                                                                                                        
|  point-mass trajectory: ISA atmosphere, Mach-dependent Cd,    |                                                                                                                        
|  altitude wind profile, spin decay, Magnus, yaw of repose     |                                                                                                                        
+------------------------------+--------------------------------+                                                                                                                        
                               |                                                                                                                                                         
        +----------------------+----------------------+                                                                                                                                  
        v                                             v                                                                                                                                  
+---------------------------+   +--------------------------------------+                                                                                                                 
| LAYER 2 — HARDWARE-IN-    |   | LAYER 3 — ONBOARD-GNC SIL            |                                                                                                                 
| THE-LOOP (HIL)            |   | (guidance_ordnance.m)                |                                                                                                                 
| (guided_sensor.m)         |   | firmware_true.ino's exact math       |                                                                                                                 
| PC flies the physics,     |   | (estimator + impact predictor +      |                                                                                                                 
| REAL ESP32 streams real   |   | guidance law) flies the round using  |                                                                                                                 
| sensor telemetry over     |   | ONLY noisy simulated baro/GPS at     |                                                                                                                 
| UART; PC streams back     |   | board rates. Validates the onboard   |                                                                                                                 
| canard commands in        |   | algorithm BEFORE flashing.           |                                                                                                                 
| real time (1x - 4x).      |   |                                      |                                                                                                                 
+---------------------------+   +--------------------------------------+                                                                                                                 

The GNC Math (implemented in firmware + validated in sim)

  • Firing solution (Chusilp 2012): bisection on gun elevation, secant
    iteration on azimuth for wind-drift cancellation.
  • State estimation on board: baro altitude via hypsometric equation;
    vertical speed from a first-order complementary filter
    vz ← 0.8·vz + 0.2·(Δh/Δt) at 10 Hz; GPS velocity smoothing at 1 Hz.
  • Impact Point Prediction (IPP) (McCoy; Raza & Wang 2022 use MPLT — we use
    the analytic point-mass equivalent an ESP32 can run in µs):
    closed-form time-to-impact τ = (vz + √(vz² + 2gz))/g, then drag-decay
    ballistic coast x_imp = x + vx·(1 − e^(−kd·τ))/kd.
  • Guidance law: saturated proportional correction
    δ = sat(Kp·(x_tgt − x_imp), ±15°), active post-apogee, 1 Hz.
  • Single-channel roll-orientation steering (Cheng 2019, Raza & Wang 2022):
    fixed-cant canards on the fuze cone; force orientation is the control
    variable, matching the dual-spin PGK architecture (M1156, Burke & Pergolizzi 2008).

System Architecture

text
                         +-------------------------+
                         |          ESP32          |
                         |    Main Controller      |
                         +------------+------------+
                                      |
              +-----------------------+-----------------------+
              |                       |                       |
              v                       v                       v
        +-----------+           +-----------+           +-----------+
        |    I2C    |           |   UART    |           |   GPIO    |
        |    Bus    |           | Interface |           |  Inputs   |
        +-----+-----+           +-----+-----+           +-----+-----+
              |                       |                       |
       +------+------+------+          |                 +----+----+
       |      |      |      |          |                 |         |
       v      v      v      |          v                 v         v
    MPU6050 BMP280 INA219  |       NEO-6M           IR Sensor   SW-240
       |      |      |      |          |             Proximity   Impact
       +------+------+------+          |                 |         |
              |                         |                 |         |
              v                         v                 |         |
       Motion / Environment       GNSS Position           |         |
              |                         |                 |         |
              +-------------+-----------+-----------------+---------+

Parts

11
QtyValueFootprintReferences
2SW_PushButton_Switch_THT:SW_PUSH_6mm_H4.3mmSW1, SW2
1ESP32-C3-DevKitM-1RF_Module:ESP32-C3-DevKitM-1U1
1LEDLED_THT:LED_D5.0mmD1
1MPU6050Connector_PinHeader_1.00mm:PinHeader_1x08_P1.00mm_VerticalJ1
1RResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_HorizontalR1
1bmp280Connector_PinHeader_1.00mm:PinHeader_1x06_P1.00mm_VerticalJ2
1impactConnector_PinHeader_1.00mm:PinHeader_1x03_P1.00mm_VerticalJ6
1ins_219Connector_PinHeader_1.00mm:PinHeader_1x06_P1.00mm_VerticalJ3
1neo6mConnector_PinHeader_1.00mm:PinHeader_1x04_P1.00mm_VerticalJ4
1proximityConnector_PinHeader_1.00mm:PinHeader_1x03_P1.00mm_VerticalJ5

Similar boards

  • 2 layers106.5 × 66 mmTry, the printed circuit board in 3D

    Try

    Ahmed-YSY/FleetGuard

    IoT vehicle telematics for fleet & logistics — ESP32 + SIM7600G 4G/GPS tracker with fuel-theft detection, tamper/cargo security alarms, offline-resilient MQTT reporting, and OBD2 data over ESP-NOW.

    18 parts6
  • 2 layers60 × 40 mmEsp ppo v2, the printed circuit board in 3D

    Esp ppo v2

    iho77/ppo_v2

    This work is licensed under a [Creative Commons Attribution-NonCommercial 4.0 International License][cc-by-nc].

    19 parts5
  • 2 layers226.3 × 90.5 mmClockclock main, the printed circuit board in 3D

    Clockclock main

    TiboDevC/clockclock

    Personal project of a kinetic clock inspired by Humans Since 1982, using 48 stepper motors to display time in an artistic and dynamic way.

    132 parts3GPL-3.0
  • 4 layers58 × 60 mmProject 6 esp32 solar prototype, the printed circuit board in 3D

    Project 6 esp32 solar prototype

    Abineshpk007/KICAD-solar_panel_monitoring_prototype

    This is my PCB, there are many outer like it but this is mine

    15 parts1
  • 2 layers115.4 × 66.5 mmCNC Router, the printed circuit board in 3D

    CNC Router

    diaxxu/CNC-Router

    a challenge i gave myself to make something great ! yes its a cnc milling / laser / plotter machine

    34 parts1MIT
  • 2 layers70.8 × 51.4 mmESS Bottom, the printed circuit board in 3D

    ESS Bottom

    shrimp-18/ESS-Wristband

    A hardware Project:- Wristband

    14 parts1
  • 2 layersControls, the printed circuit board in 3D

    Controls

    VladimirVladimirovMinkov/UOA_HPA

    This is a code and document repository for the University of auckland Aeronaughtics Club Human Powered Aircraft

    16 parts1
  • 2 layers137 × 54.5 mmHackthon PCB, the printed circuit board in 3D

    Hackthon PCB

    vruga/esp_medmonitor

    KiCAD project for dual-node ESP32 medical monitoring and security system.

    10 parts1

Questions

What parts does the Hail Mary use?

11 parts, built around the ESP32-C3-DEVKITM-1 and BMP280. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Hail Mary KiCad files?

From the saniyafatima07/Hail_Mary repository on GitHub, at the commit this page was made from: the board is hardware/PCB/Hail_Mary.kicad_pcb and its schematic hardware/PCB/Hail_Mary.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Hail Mary design in my own project?

Its repository states no licence, so its author keeps all rights: ask saniyafatima07 before reusing the design.