Skip to the content
4 layers14 × 56 mmProbe, the printed circuit board in 3D

Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity…

Size
14 × 56 mm
Copper layers
4
Thickness
1.6 mm
Parts
22
Nets
12
Pads
97
Tracks, vias
330, 23
Pours
5
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
17 Oct 2026
Updated
30 Oct 2026

Overview

Probe is an open-source printed circuit board by vbartusevicius, from the vbartusevicius/weather-station repository on GitHub. It is a 4-layer board of 14 × 56 mm with 22 parts on 12 nets, routed with 330 tracks and 23 vias.

It is built around the BMP585, SGP41-D-R4 and SHT40-AD1F-R2, with the LM2903DR2GH, SCD41-D-R2 and AO3400A among its other parts. Its parts include 7 resistors, 6 capacitors, 5 ICs, 2 connectors and 1 transistor. It belongs with the sensors and measurement boards of this library.

Main components

6

README

README.md

AeroMet V1 — Solid-State Roof Weather & Air-Quality Station

CI

Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity, pressure, lightning, PM1 / PM2.5 / PM10, VOC / NOx and true CO₂. It runs from 12–32 V DC, talks Wi-Fi and RS-485, serves its own web dashboard and appears in Home Assistant by itself.

AeroMet station, 3D renderWeb UI: Now tab

What it measures · Hardware · Web UI · Build one · Firmware · Development

What it measures

MeasurementSensorRange
Wind speed & direction4× 40 kHz ultrasonic transducers, time of flight (STM32G431 crown)0–60 m/s, 0.1°
Rain & hail4 piezo discs under the lid, acoustic impacts0–200 mm/h, hail size
UV index, UV-A / UV-B, sunlight, night skyGUVB-C21SD + GUVA-C22SD photodiodes + TSL25911 under a PTFE domeUVI 0–16+, 0.0002–88 000 lx
Temperature & humiditySensirion SHT40 in a 5-plate radiation shield±0.2 °C, ±1.8 % RH
Pressure & thunderBosch BMP585±0.06 hPa
ParticulatesPlantower PMSA003IPM1 / PM2.5 / PM10
VOC & NOxSensirion SGP41 + Gas Index Algorithmindex 1–500
CO₂Sensirion SCD41 (heated below −8 °C)400–5000 ppm
LightningAS3935 + 500 kHz ferrite antenna1–40 km
Compass, tilt, vibrationMMC5603 + LSM6DS3heading, mast tilt, ground vibration

Full sensor, enclosure and board reference: docs/hardware.md.

Hardware

CutawayExplodedSix boards on one breakaway panel
CutawayExploded viewPCB panel, KiCad 3D render
radiation shield, probe cartridge, base bay13 printed parts, bayonet and threaded jointscrown, main, probe, power, dome, reflector (4-layer, 140.6 × 63.2 mm)
More renders: inside view, every printed part, board plots
InsideBasePagodaWind tunnel
Insidebasepagodawind_tunnel
Crown baseCrown lidStrutsProbe sleeve
crown_basecrownstrutsprobe_sleeve_front

Board plots (top / bottom SVG): crown · main · probe · power · dome · reflector · panel

Web UI

The station serves its dashboard over Wi-Fi (no cloud, no app). Every value is computed by the firmware; the page only displays it.

NowTrends
Now tabTrends tab
live readings, forecast, sun & moon, air quality, lightningany metrics from 1 hour to 6 months, wind rose, records, CSV export
CalibrationSetup
Calibration tabSetup tab
station health, home calibration with household itemsWi-Fi, MQTT / Home Assistant, RS-485 monitor, firmware update

Also: MQTT with Home Assistant auto-discovery, and an RS-485 poll / response protocol (CRC-16 frames with every sensor) for wired loggers.

Build one

  1. Order the boards with assembly: ODB++ for AISLER, Gerbers + MPN BOM + CPL for PCBWay / Eurocircuits, or the JLCPCB files for the breakaway panel (hardware/releases/v1/; which file goes where: docs/building.md).
  2. Print the enclosure: 8 print plates in enclosure/print/ (MJF / SLS nylon or ASA), plus standard O-rings and a turned PTFE dome.
  3. Assemble and seal: harnesses, conformal coating and sealing in docs/building.md.
  4. Flash the station once over USB, then bring it up and calibrate it at home: CALIBRATION.md.

Open design questions and acceptance checks: REVIEW_CHECKLIST.md.

Firmware

Download from Releases: each release carries the firmware and the complete hardware package (aeromet-hardware-v1.zip: Gerbers, BOM, CPL, STL / STEP print plates, drawings, build and calibration guides). Every commit to main that passes CI is released, named after its UTC commit time (2026.10.24.0040); the firmware reports the same version.

FileUse
usb-flash-firmware.binfirst flash of a new board over USB: esptool.py --chip esp32c6 write_flash 0x0 usb-flash-firmware.bin
firmware.binlater updates from the Web UI (Setup → Firmware update); carries the crown firmware too

The version is the UTC commit time, yyyy.mm.dd.hhmm. Local build: python3 station/scripts/release_firmware.py → station/build/firmware/.

Development

FolderContents
hardware/spec (product/spec.yaml), SKiDL circuits, KiCad layouts, simulations, release package
mechanical/CadQuery enclosure generator and renderer
station/ESP32-C6 firmware (ESP-IDF), Web UI (station/data/), simulator, unit and Web UI tests
crown/STM32G431 crown firmware (ultrasonic wind, rain, lightning)
bash
python3 hardware/scripts/build.py                     # everything: hardware, CAD, release, firmware, tests
docker compose --profile lint run --rm -T cpp-lint "pio test -d station -e native"   # firmware unit tests
python3 station/scripts/mock_webui_server.py          # Web UI on the simulator: http://127.0.0.1:8765
docker compose --profile lint run --rm lint check .   # lint
python3 docs/render_readme_images.py                  # refresh the README screenshots and PCB render

Architecture, conventions and every command: AGENTS.md.

Parts

22
QtyValueFootprintReferences
5100n 50VCapacitor_SMD:C_0603_1608MetricC2, C3, C4, C5, C6
310kResistor_SMD:R_0603_1608MetricR3, R4, R6
2680RResistor_SMD:R_1206_3216MetricR1, R2
110k NTCResistor_SMD:R_0603_1608MetricTH1
110u 10VCapacitor_SMD:C_0603_1608MetricC1
1470kResistor_SMD:R_0603_1608MetricR7
151kResistor_SMD:R_0603_1608MetricR5
1AO3400Agateway_fp:AOS_AO3400A_SOT-23Q1
1BMP585gateway_fp:Bosch_BMP585_LGA-9U5
1LM2903DR2Ggateway_fp:ON_LM393DR2G_SOIC-8U4
1Main boardConnector_JST:JST_SH_BM10B-SRSS-TB_1x10-1MP_P1.00mm_VerticalJ1
1Reflector T-Socket SMDgateway_fp:HX_PM2.54-1x4P-RA-SMDJ2
1SCD41-D-R2gateway_fp:Sensirion_SCD41_LGA-20U1
1SGP41-D-R4gateway_fp:Sensirion_SGP41_DFN-6U2
1SHT40-AD1F-R2gateway_fp:Sensirion_SHT45_DFN-4U3

More from vbartusevicius/weather-station

7
  • 4 layers120 × 76 mmPanel, the printed circuit board in 3D

    Panel

    vbartusevicius/weather-station

    Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity…

    235 parts
  • 4 layers60 × 60 mmCrown, the printed circuit board in 3D

    Crown

    vbartusevicius/weather-station

    Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity…

    95 parts
  • 4 layers32 × 52 mmWeather station, the printed circuit board in 3D

    Weather station

    vbartusevicius/weather-station

    Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity…

    47 parts
  • 4 layers28.5 × 21.5 mmPower, the printed circuit board in 3D

    Power

    vbartusevicius/weather-station

    Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity…

    40 parts
  • 4 layers15.6 × 15.2 mmDome, the printed circuit board in 3D

    Dome

    vbartusevicius/weather-station

    Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity…

    16 parts
  • 4 layers13.6 × 13.6 mmDome legacy, the printed circuit board in 3D

    Dome legacy

    vbartusevicius/weather-station

    Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity…

    7 parts
  • 4 layers24 × 24 mmReflector, the printed circuit board in 3D

    Reflector

    vbartusevicius/weather-station

    Open-source rooftop weather and air-quality station with no moving parts (Ø 96 × 235 mm, UV-stabilised ASA): ultrasonic wind, acoustic rain and hail, UV / sunlight / night-sky brightness, temperature, humidity…

    7 parts

Similar boards

  • 4 layers65 × 56 mmSensor HAT, the printed circuit board in 3D

    Sensor HAT

    Eniemooo/Sensor-HAT

    Open-hardware indoor air sensor (CO2, VOC/NOx, T/RH, light, sound): HAT for Raspberry Pi or standalone with Seeed XIAO + ESPHome. KiCad 10.

    112 parts
  • 4 layers60 × 80 mmWisp, the printed circuit board in 3D

    Wisp

    huulanka/wisp

    Open-source ESP32 room climate monitor — CO2, VOC, humidity, temperature and light sensing with custom PCB, MQTT/HomeKit integration, and OTA firmware updates. Full hardware + software, from schematic to BOM.

    91 partsMIT
  • 4 layers75 × 56.4 mmEsp32-c6-wroom1 board, the printed circuit board in 3D

    Esp32-c6-wroom1 board

    pushtiujeniya/esp32-c6-environmental-logger

    This repository contains an Environmental Sensor Station and Data Logger powered by the ESP32-C6-WROOM-1 microcontroller.

    59 parts4
  • 2 layers75 × 75 mmAir quality pcb, the printed circuit board in 3D

    Air quality pcb

    aleemacc/air_quality_sensor

    PCB design for a custom air quality measuring device

    30 parts
  • 6 layers60 × 100 mmSenseboard, the printed circuit board in 3D

    Senseboard

    CPSLO-AI-Campus-Fire-Detection/senseboard

    PCB for sensor stack and compute for fire detection system

    109 partsAGPL-3.0
  • 2 layers7.2 × 41.9 mmSensor puck, the printed circuit board in 3D

    Sensor puck

    david072/sensor_puck

    60 parts
  • 4 layers25.5 × 62.8 mmAqproto, the printed circuit board in 3D

    Aqproto

    HOUXA8/aqproto

    Personal Project

    31 parts
  • 2 layers49 × 50.4 mmAirMonitor, the printed circuit board in 3D

    AirMonitor

    JJendryka/AirMonitor

    60 parts

Questions

How big is the Probe PCB?

It measures 14 × 56 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Probe use?

22 parts, built around the BMP585, SGP41-D-R4, SHT40-AD1F-R2 and LM2903DR2GH. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Probe KiCad files?

From the vbartusevicius/weather-station repository on GitHub, at the commit this page was made from: the board is hardware/releases/v1/probe/probe.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Probe design in my own project?

Its repository states no licence, so its author keeps all rights: ask vbartusevicius before reusing the design.