Skip to the content
2 layers85 × 56 mmPWM, the printed circuit board in 3D

Contains schematics and PCB file for use with open source Reef-PI software

Size
85 × 56 mm
Copper layers
2
Thickness
1.6 mm
Parts
81
Nets
62
Pads
243
Tracks, vias
511, 0
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
6 Aug 2018
Updated
22 Dec 2018

Overview

PWM is an open-source printed circuit board by vandegraaf, from the vandegraaf/Reef-PI_PCBs repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 85 × 56 mm with 81 parts on 62 nets, routed with 511 tracks and 0 vias.

It is built around the PCA9685PW. Its parts include 32 resistors, 23 connectors, 16 transistors, 3 capacitors and 2 ICs.

Main components

1

README

README.md

Reef-PI_PCBs

Contains schematics and PCB file for use with open source Reef-PI software

2 boards are presently uploaded: HAT (interface to Raspberry 2 or 3) with following functions:

  • Can drive up to 16 external relais modules
  • Can drive up to 2 12V dosing pumps
  • Can use up to 2 optical ATO (water) sensors
  • Can drive multiple DS18B20 temperature sensors
  • Can connect to external I2C boards (not yet tested) It requires an external 12V power supply to operate the dosing pumps This board has been tested (except I2C, but should be ok). No changes were made to the schematics, but some improvements to power and dosing connections have been made to the PCB The HAT documentation contains all information of which connectors and related GPIO signals to use

New PWM module added New Reef-PI_PWM v1.0 PCB files added (no documentation yet). These files have some minor improvements over the tested v0.3, mainly to avoid a potential collission with the DS18B20 connector on the Reef-PI_HAT. No changes have been made to the schematics between v0.3 and v1.0 of the PCB. This Reef-PI_PWM module fits on top of the Reef-PI_HAT but can of course also be connected via wiring. It must be noted that the distance between the 2.5mm PWM output connectors is very small, only very small 2.5mm connectors will fit if all 16 channels are going to be used. The documentation provides a potential candidate.

Parts

81
QtyValueFootprintReferences
16MJ1-2503A:CUI_MJ1-2503AJ8, J9, J10, J11, J12, J13, J14, J15, J16, J17, J18, J19, J20, J21, J22, J23
1610KResistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR1, R2, R3, R4, R5, R6, R7, R8, R17, R19, R21, R23, R25, R27, R29, R31
161KResistors_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P2.54mm_VerticalR9, R10, R11, R12, R13, R14, R15, R16, R18, R20, R22, R24, R26, R28, R30, R32
16BC184BTO_SOT_Packages_THT:TO-92_Inline_Narrow_OvalQ1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10, Q11, Q12, Q13, Q14, Q15, Q16
6JumperJumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mmJ2, J3, J4, J5, J6, J7
4Mounting_Holes:MountingHole_2.7mm_M2.5_DIN965, , ,
2100nfCapacitors_THT:C_Disc_D6.0mm_W2.5mm_P5.00mmC2, C3
1330uFCapacitors_SMD:CP_Elec_8x10C1
1Conn_01x06_MalePin_Headers:Pin_Header_Straight_1x06_Pitch2.54mmJ1
1PCA9685PWHousings_SSOP:TSSOP-28_4.4x9.7mm_Pitch0.65mmU1
1R_Network06Resistors_THT:R_Array_SIP7RN1
1uA7810TO_SOT_Packages_THT:TO-220-3_HorizontalU2

More from vandegraaf/Reef-PI_PCBs

1
  • 2 layers65 × 56 mmHAT, the printed circuit board in 3D

    HAT

    vandegraaf/Reef-PI_PCBs

    Contains schematics and PCB file for use with open source Reef-PI software

    25 parts8GPL-3.0

Similar boards

  • 2 layers220 × 329.2 mmControl Boards, the printed circuit board in 3D

    Control Boards

    nasa-jpl/open-source-rover

    A build-it-yourself, 6-wheel rover based on the rovers on Mars!

    148 parts9.8kApache-2.0
  • 4 layers100.1 × 60.2 mmHades, the printed circuit board in 3D

    Hades

    pms67/HadesFCS

    Complete flight control system designed from scratch. Hardware designed with KiCad.

    215 parts1kBSD-3-Clause
  • 2 layers94 × 79 mm5 - Lizard Car, the printed circuit board in 3D

    5 - Lizard Car

    TRD-B/Lizard

    3D printed RC race car with custom electronics

    54 parts129CC-BY-4.0
  • 2 layers54.2 × 75.2 mmKiCAD Design, the printed circuit board in 3D

    KiCAD Design

    Brobiwann/ESP-spider

    The ESP-Spider is a quadruped robot inspired by the miniKame (https://github.com/JavierIH/miniKame) . Like the miniKame, it uses sinusoidal functions to control servo positions, but the design and code were developed…

    70 parts44
  • 2 layers130.6 × 112 mmSWN, the printed circuit board in 3D

    SWN

    4ms/SWN

    Spherical Wavetable Navigator source code

    614 parts43
  • 2 layers156.2 × 168.9 mmLPC176x MultiFunction, the printed circuit board in 3D

    LPC176x MultiFunction

    RobertPHeller/RPi-RRCircuits

    A collection of circuit designs for various MCUs, not just Raspberry Pis relating to Model Railroading

    236 parts24
  • 2 layersHB LC Dim6PWM CV, the printed circuit board in 3D

    HB LC Dim6PWM CV

    stan23/myPCBs

    Verschiedene Platinen für HomeMatic, AskSinPP und SmartHome

    57 parts21

Questions

How big is the PWM PCB?

It measures 85 × 56 mm and has 2 copper layers, 1.6 mm thick.

What parts does the PWM use?

81 parts, built around the PCA9685PW. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the PWM KiCad files?

From the vandegraaf/Reef-PI_PCBs repository on GitHub, at the commit this page was made from: the board is PWM.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the PWM design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).