

Core board
An experimental flight controller/altimeter board family developed by UNL Aerospace Rocketry
- Size
- 27 × 60 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 39
- Nets
- 56
- Pads
- 164
- Tracks, vias
- 253, 33
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 1 Aug 2024
- Updated
- 27 Nov 2024
Overview
Core board is an open-source printed circuit board by unl-rocketry, from the unl-rocketry/flight-computer repository on GitHub, published under the CERN-OHL-S-2.0 licence. It is a 2-layer board of 27 × 60 mm with 39 parts on 56 nets, routed with 253 tracks and 33 vias.
It is built around the BME280, TPS62172DSG and CPC1002N, with the BNO055 among its other parts. Its parts include 11 resistors, 7 connectors, 6 ICs, 3 capacitors and 2 diodes.
Main components
4BME280
LGA-8(2.5x2.5)-40℃~+85℃ 0%RH~100%RH 1.71V~3.6V 1.8uA 16bit I2C、SPI ±0.5℃ ±3%RH LGA-8(2.5x2.5) Temperature and Humidity Sensor ROHSBoschTemperature And Humidity SensorTPS62172DSG
WSON-8-EP(2x2)-40℃~+85℃@(TA) 1 17uA 2.25MHz 3.3V 3V~17V 500mA Buck Built-in Fixed Overcurrent Protection、Light load efficient mode、Operating status indication Step-down type Yes WSON-8-EP(2x2) DC-DC Converters ROHSTexas InstrumentsDC-DC ConvertersCPC1002N
SOP-4-2.54mm-40℃~+85℃ 1.2V 1.3ms 1.5kV 400mW 410us 550mΩ 60V 700mA DC One set normally open: 2A (SPST - normally open) SOP-4-2.54mm Solid State Relays (MOS Output) ROHSLittelfuse/IXYSSolid State Relays (MOS Output)BNO055
LGA-28(3.8x5.2)-40℃~+85℃ 2.4V~3.6V 40uA I2C、UART IMU X,Y,Z X,Y,Z ±16g ±2000dps LGA-28(3.8x5.2) Accelerometers ROHSBosch SensortecAccelerometers
README
README.mdFlight Computer
A versatile, inexpensive, modular, and open source flight computer and altimeter system for amateur and experimental rocketry.
All designs in this repository are licensed under the CERN-OHL-S v2 or any later version. Contributions are welcome!
Core Board
This design should be capable of using input voltages from 3v → 16v on the battery input to allow for a wide range of batteries to be used. It is designed to control and independently fire up to 3 individual high power in-flight events (eg. ejection charges).
Built-in Sensors
The sensor package includes a Bosch BNO055 motion co-processor for acceleration, magnetic heading, and 3d orientation. It also includes a Bosch BME280 sensor for pressure (along with altitude), temperature, and humidity measurements. These sensor measurements can be used for flight control, and can also be logged to a MicroSD card mounted on the board for ease of data recovery.
Toolchain Support
All programmable components of this board were selected to be compatible with Rust-based microcontroller frameworks like Embassy, for ease of programming and future extension of software capabilities.
Images
Expansion Modules
A major feature of the Core Board is the ability to be expanded by connecting via an I2C (and hopefully in the future CAN Bus) connection to other boards and sensors with the same connectors. These expansion boards could provide additional capabilities while being modular for quickly swapping and replacing parts.
The connectors on the Core Board are compatible with any Adafruit Stemma QT or SparkFun Qwiic board, which immediately provides for a lot of options for sensors without any design or soldering work needed.
In the future, this repository will host the KiCad files for expansion boards created by UNL Aerospace Rocketry.
Parts
39| Qty | Value | Footprint | References |
|---|---|---|---|
| 8 | 4.4k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R5, R7, R10, R11 |
| 4 | MountingHole | MountingHole:MountingHole_2.2mm_M2_ISO7380_Pad | H1, H2, H3, H4 |
| 3 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R8, R9 |
| 3 | CPC1002N | Package_SO:SOP-4_3.8x4.1mm_P2.54mm | U1, U2, U3 |
| 2 | 22pF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C2 |
| 2 | Conn_01x13_Socket | Connector_PinHeader_2.54mm:PinHeader_1x13_P2.54mm_Vertical | J1, J2 |
| 2 | LOGO | LOGO | G***, G*** |
| 1 | 0.1µF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C3 |
| 1 | 10µF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | f1 |
| 1 | 2.2µH | Inductor_SMD:L_0603_1608Metric_Pad1.05x0.95mm_HandSolder | L1 |
| 1 | 32.768kHz | Crystal:Crystal_SMD_G8-2Pin_3.2x1.5mm_HandSoldering | Y1 |
| 1 | BME280 | Package_LGA:Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U4 |
| 1 | BNO055 | Package_LGA:LGA-28_5.2x3.8mm_P0.5mm | U5 |
| 1 | Battery | Jumper:SolderJumper-2_P1.3mm_Bridged_Pad1.0x1.5mm | JP1 |
| 1 | Battery Input | Connector_JST:JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | J5 |
| 1 | Connector 1 | G2Custom:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical-CUSTOM | J7 |
| 1 | Connector 2 | G2Custom:JST_SH_BM04B-SRSS-TB_1x04-1MP_P1.00mm_Vertical-CUSTOM | J8 |
| 1 | D | Diode_SMD:D_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1 |
| 1 | Ignitor Output | TerminalBlock_Phoenix:TerminalBlock_Phoenix_MPT-0,5-4-2.54_1x04_P2.54mm_Horizontal | J3 |
| 1 | LED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2 |
| 1 | Micro_SD_Card | Connector_Card:microSD_HC_Hirose_DM3D-SF | J4 |
| 1 | TPS62172DSG | Package_SON:WSON-8-1EP_2x2mm_P0.5mm_EP0.9x1.6mm_ThermalVias | U6 |
Similar boards
- 4 layers136.2 × 25 mm

- 2 layers133.4 × 97.8 mm

SmartIOv3.3
igg-iot/BBD9000
Automated Biodiesel Dispensing Kiosk and Coop Management Software - A Free Software and Hardware Project
126 parts2 - 2 layers114.8 × 68.6 mm

- 4 layers39 × 85 mm

- 4 layers67 × 140.3 mm

- 2 layers94 × 94 mm

- 2 layers

- 2 layers40 × 40 mm

Tinkerforge industrial quad relay v2 bricklet industrial quad relay v2
oomlout/oomlout_oomp_project_bot_v_2
36 parts
Questions
How big is the Core board PCB?
It measures 27 × 60 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Core board use?
39 parts, built around the BME280, TPS62172DSG, CPC1002N and BNO055. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Core board KiCad files?
From the unl-rocketry/flight-computer repository on GitHub, at the commit this page was made from: the board is core_board/core_board.kicad_pcb and its schematic core_board/core_board.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Core board design in my own project?
Its repository publishes it under the CERN-OHL-S-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).