
Iaq device
nkitanov/iaq_board
IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality

Kicad8 is an open-source printed circuit board by UniversalProgressions, from the UniversalProgressions/WeMos-Shield-PCB-Board repository on GitHub. It is a 2-layer board of 99 × 99 mm with 14 parts on 17 nets, routed with 445 tracks and 1 via.
It is built around the WEMOS D1 MINI. Its parts include 7 connectors, 4 ICs, 1 resistor, 1 diode and 1 switch. It belongs with the ESP8266 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | WeMos_D1_mini | Module:WEMOS_D1_mini_light | U1, U2, U3, U4 |
| 1 | Conn_01x05_Pin - 3.3V | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J4 |
| 1 | Conn_01x05_Pin - 5V | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J5 |
| 1 | Conn_01x05_Pin - GND | Connector_PinSocket_2.54mm:PinSocket_1x05_P2.54mm_Vertical | J3 |
| 1 | Conn_01x08_Pin_Left | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J2 |
| 1 | Conn_01x08_Pin_Left | TerminalBlock_RND:TerminalBlock_RND_205-00018_1x08_P5.00mm_Horizontal | J6 |
| 1 | Conn_01x08_Pin_Right | TerminalBlock_RND:TerminalBlock_RND_205-00018_1x08_P5.00mm_Horizontal | J7 |
| 1 | Conn_01x08_Pin_Right | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | LED | LED_THT:LED_D3.0mm | D1 |
| 1 | R | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R1 |
| 1 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H5mm | SW1 |

nkitanov/iaq_board
IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality

bitfixer/bf-romulator
Romulator - RAM/ROM replacement and debug for 6502 CPU systems

alcar21/WemosEM
Cheap power monitor (STC013) with Home Assistant Discover and Wemos D1 Mini / PRO (esp8266)

kholia/Easy-Digital-Beacons-v1
A simple and easy Arduino / Pi Pico / ESP8266-powered WSPR, FT8, and FT4 beacon system which uses NTP + DS3231 RTC for timing. Super extensible! Now comes with optional GPS support.

htumanyan/navien
Navien water heater wire protocol for communication with NaviLink and other attached devices


It measures 99 × 99 mm and has 2 copper layers, 1.6 mm thick.
14 parts, built around the WEMOS D1 MINI. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the UniversalProgressions/WeMos-Shield-PCB-Board repository on GitHub, at the commit this page was made from: the board is Kicad8.kicad_pcb and its schematic Kicad8.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask UniversalProgressions before reusing the design.