

Repeater memris V2a
Repeater U/V FM, AFSK
- Size
- 96 × 83 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 76
- Nets
- 71
- Pads
- 278
- Tracks, vias
- 52, 20
- Pours
- 4
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 8 Sep 2024
- Updated
- 12 Nov 2024
Overview
Repeater memris V2a is an open-source printed circuit board by ub1qbm, from the ub1qbm/LobachevskySat repository on GitHub. It is a 4-layer board of 96 × 83 mm with 76 parts on 71 nets, routed with 52 tracks and 20 vias.
It is built around the ATMEGA328-AU, SA868-U and SPF5043Z, with the AMS1117-3.3 and MMBT2222A among its other parts. Its parts include 23 capacitors, 23 resistors, 6 ICs, 5 inductors and 2 diodes. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
5ATMEGA328-AU
TQFP-32(7x7)-40℃~+85℃ 1.8V~5.5V 10bit 1KB 20MHz 23 2KB 32KB 8 Bit AVR Built-in FLASH TQFP-32(7x7) Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)SA868-U
SMD,19x35.6mmSleep wake-up function SMD,19x35.6mm RF Modules ROHSG-NiceRFModulesSPF5043Z
SOT-343-40℃~+85℃ 0.8dB 16dB 17.5dB 18.2dB 22.7dBm 35dBm 4.75V~5.25V 46mA 50MHz~4GHz Linearization design、Bias control circuit SOT-343 RF Amplifiers ROHSQorvoRF AmplifiersAMS1117-3.3
SOT-223-40℃~+125℃ 0.003%Vout 1 1.1V@(800mA) 15V 1A 3.3V 5mA 72dB@(120Hz) Fixed Over Current Protection、Short Circuit Protection、Thermal shutdown Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSAdvanced Monolithic SystemsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMMBT2222A
SOT-23-55℃~+150℃ 1 NPN 100 100nA 1V 300MHz 300mW 40V 600mA 6V NPN Standalone SOT-23 Bipolar (BJT) ROHShongjiachengBipolar (BJT)
Parts
76| Qty | Value | Footprint | References |
|---|---|---|---|
| 9 | 100nF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C4, C5, C6, C8, C10, C14, C18 |
| 9 | 1K | Resistor_SMD:R_0603_1608Metric | R1, R2, R4, R5, R13, R14, R15, R20, R23 |
| 7 | TestPoint | TestPoint:TestPoint_Loop_D1.80mm_Drill1.0mm_Beaded | TP3, TP4, TP5, TP6, TP7, TP13, TP15 |
| 6 | MountingHole_Pad | MountingHole:MountingHole_2.7mm_Pad_Via | H1, H2, H3, H4, H5, H6 |
| 5 | 4.7uF | Capacitor_SMD:C_0603_1608Metric | C9, C13, C15, C16, C17 |
| 4 | 220R | Resistor_SMD:R_0603_1608Metric | R18, R19, R21, R22 |
| 3 | 0R | Resistor_SMD:R_0603_1608Metric | R9, R11, R12 |
| 3 | 8.2nH | Spacemanic_SMD:L_0603_HS | L9, L10, L11 |
| 2 | 1.8pF | Spacemanic_SMD:C_0603_HS | C31, C33 |
| 2 | 10uF | Capacitor_SMD:C_0603_1608Metric | C3, C7 |
| 2 | 150K | Resistor_SMD:R_0603_1608Metric | R16, R17 |
| 2 | 15pF | Spacemanic_SMD:C_0603_HS | C30, C34 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C11, C12 |
| 2 | 22nH | Spacemanic_SMD:L_0603_HS | L8, L12 |
| 2 | LED | LED_SMD:LED_0603_1608Metric | D1, D2 |
| 2 | MMBT2222A | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 1 | *R | Resistor_SMD:R_0603_1608Metric | R8 |
| 1 | 10pF | Spacemanic_SMD:C_0603_HS | C32 |
| 1 | 270R | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 2K | Resistor_SMD:R_0603_1608Metric | R3 |
| 1 | 4016 | Package_DIP:DIP-14_W7.62mm_LongPads | U5 |
| 1 | 4K | Resistor_SMD:R_0603_1608Metric | R6 |
| 1 | 8K | Resistor_SMD:R_0603_1608Metric | R7 |
| 1 | AMS1117-3.3 | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U2 |
| 1 | ATmega328-A | Package_QFP:TQFP-32_7x7mm_P0.8mm | U1 |
| 1 | Conn_01x06_Socket | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J2 |
| 1 | Crystal_GND2 | CSTCE16M0V53-R0:CSTCE16M0V53-R0 | Y1 |
| 1 | SA868-U | SA868:SA868 | U3 |
| 1 | SA868-V | SA868:SA868 | U4 |
| 1 | SPF5043Z | Package_TO_SOT_SMD:SOT-343_SC-70-4 | U6 |
More from ub1qbm/LobachevskySat
2- 2 layers96 × 96 mm

- 2 layers

Similar boards
- 4 layers130 × 146 mm

Board a routed pass1 fixed
ajisrawi/passive-radar-counter-drone
Passive radar for counter-drone using DVB-T, 4G and 5G: simulation, receiver hardware, FPGA micro-Doppler firmware, antennas, enclosure
194 parts3 - 2 layers150 × 85 mm

RX 50MHz SDR
ne9n/RC_6m
This project focuses on designing and building a modern 50MHz (6-meter) radio control system using the amateur radio bands.
44 parts - 4 layers100 × 75 mm

- 2 layers101.6 × 147.3 mm

Karabas pro revER
andykarpov/karabas-pro
FPGA based retrocomputer with FDD and HDD controllers
223 parts37MIT - 2 layers183.2 × 65.1 mm

- 2 layers55 × 35 mm

- 2 layers98 × 68 mm

- 2 layers35.6 × 99.8 mm

Questions
How big is the Repeater memris V2a PCB?
It measures 96 × 83 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Repeater memris V2a use?
76 parts, built around the ATMEGA328-AU, SA868-U, SPF5043Z and AMS1117-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Repeater memris V2a KiCad files?
From the ub1qbm/LobachevskySat repository on GitHub, at the commit this page was made from: the board is Repeater_memris_V2a/Repeater_memris_V2a.kicad_pcb and its schematic MEMRICK_V2/MEMRICK_V2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Repeater memris V2a design in my own project?
Its repository states no licence, so its author keeps all rights: ask ub1qbm before reusing the design.