Button transmitter
- Size
- 59.6 × 55.9 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 43
- Nets
- 34
- Pads
- 115
- Tracks, vias
- 211, 90
- Pours
- 11
- Routed
- Yes
- KiCad
- KiCad 7 (file 20221018)
- Created
- 24 Mar 2024
- Updated
- 27 Oct 2025
Overview
Button transmitter is an open-source printed circuit board by twfth9, from the twfth9/CW-Tracker repository on GitHub. It is a 2-layer board of 59.6 × 55.9 mm with 43 parts on 34 nets, routed with 211 tracks and 90 vias.
It is built around the ATTINY212-SSN and SI5351B-B-GM. Its parts include 10 resistors, 7 connectors, 5 capacitors, 5 diodes and 2 ICs. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Main components
2ATTINY212-SSN
SOIC-8-40℃~+105℃ 1.8V~5.5V 10bit 128Byte 20MHz 2KB 6 64Byte 8 Bit 8bit AVR Built-in FLASH SOIC-8 Microcontrollers (MCU/MPU/SOC) ROHSMicrochip TechnologyMicrocontrollers (MCU/MPU/SOC)SI5351B-B-GM
QFN-20-EP(4x4)-40℃~+85℃ 1.71V~3.6V 200MHz QFN-20-EP(4x4) Clock Generators, PLLs, Frequency Synthesizers ROHSSilicon LabsClock Generators, PLLs, Frequency Synthesizers
Parts
43| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 68R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R1, R2, R3, R4, R5 |
| 5 | Jumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_TrianglePad1.0x1.5mm | JP1, JP2, JP3, JP4, JP5 |
| 4 | M3 | MountingHole:MountingHole_3.2mm_M3_Pad | H1, H2, H3, H4 |
| 3 | 0R | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R6, R7, R8 |
| 3 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C1, C3, C5 |
| 3 | GRN | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D2, D3, D4 |
| 3 | SMA | Connector_Coaxial:SMA_Amphenol_132134-16_Vertical | J7, J8, J9 |
| 2 | 10uF | Capacitor_SMD:C_0805_2012Metric_Pad1.18x1.45mm_HandSolder | C2, C4 |
| 2 | 1k8 | Resistor_SMD:R_1206_3216Metric | R9, R10 |
| 2 | RED | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D5 |
| 1 | 1.27mm Pogo Pads | Library:2x3_1.27mm_Pogo_Header | J2 |
| 1 | 2.54mm | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | 2.54mm | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | 2.54mm | Connector_PinHeader_2.54mm:PinHeader_2x03_P2.54mm_Vertical | J10 |
| 1 | 25MHz | Library:Crystal_SMD_Kyocera_CX3225SB-4Pin_3.2x2.5mm | Y1 |
| 1 | ATtiny212-SS | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1 |
| 1 | Battery_Cell | Library:BAT_1066 | BT1 |
| 1 | LOGO | Library:IPL_Logo_10mm | G*** |
| 1 | LOGO | Library:Logo_10mm_inv | G*** |
| 1 | SW_SPDT | Library:SLW-121586-5A-D | SW1 |
| 1 | Si5351B | Package_SO:MSOP-10_3x3mm_P0.5mm | U2 |
More from twfth9/CW-Tracker
3- 4 layers

- 2 layers

- 2 layers42 × 21 mm

Similar boards
- 2 layers

Wiggle spine
gitter-badger/wiggleport
Modular I/O for multi-channel sound, light, and motion
173 partsMIT - 2 layers88.9 × 114.3 mm

Raw
PCBench/PCBench
resolution = [0.5, 0.5] pcbfolder = '../PCBs/' pcbnames = ["1Bitsy1bitsy"] iters = 30 env = PCBRoutingEnv(resolution=resolution, pcbfolder=pcbfolder, pcbnames=pcbnames) obs, info = env.reset() for in range(iters): act =…
190 parts21MIT - 2 layers99.6 × 99.2 mm

Ctfl rakete tht
jostsalathe/ctfl-rakete-pcb
Converting this sticker desing into a PCB that lights up its flame and lighthouse top from the bottom side using some LEDs and a coin cell battery.
30 parts1 - 4 layers

IgnisV2
TehoorMarjan/Ignis
An autonomous flame-shaped lamp/nightlight controlled by microcontroller with WS2812B LED ring and integrated Qi wireless charging. 🔥
86 parts1 - 2 layers17.8 × 14 mm

ATtiny8SIOCbg
CmdrZin/Educational-Projects
A group of educational projects to promote hardware and software development.
3 parts1MIT - 2 layers52.2 × 52.2 mm

Base
google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards
43 parts3kApache-2.0 - 2 layers146.1 × 49.5 mm

Breakout 121pin 368255-2-Connector
rusefi/rusefi
rusefi - GPL internal combustion engine control unit
43 parts1.2k - 2 layers33 × 34 mm

Questions
How big is the Button transmitter PCB?
It measures 59.6 × 55.9 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Button transmitter use?
43 parts, built around the ATTINY212-SSN and SI5351B-B-GM. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Button transmitter KiCad files?
From the twfth9/CW-Tracker repository on GitHub, at the commit this page was made from: the board is Transmitter/KiCAD/Button Transmitter/Prototypes/Si5351A-ATtiny212 Dev A/button_transmitter.kicad_pcb and its schematic Transmitter/KiCAD/220MHz Oscillator/220_MHz_Oscillator.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Button transmitter design in my own project?
Its repository states no licence, so its author keeps all rights: ask twfth9 before reusing the design.