Skip to the content
2 layers44.5 × 16.5 mmDht11, the printed circuit board in 3D
Size
44.5 × 16.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
5
Nets
4
Pads
10
Tracks, vias
15, 0
Pours
2
Routed
Yes
KiCad
KiCad 4
Created
22 Jun 2017
Updated
4 Jul 2018

Overview

Dht11 is an open-source printed circuit board by tuankiet65, from the tuankiet65/pnc-modules repository on GitHub. It is a 2-layer board of 44.5 × 16.5 mm with 5 parts on 4 nets, routed with 15 tracks and 0 vias.

It is built around the DHT11. Its parts include 1 resistor, 1 IC and 1 connector.

Main components

1

Parts

5
QtyValueFootprintReferences
110kResistors_SMD:R_1206_HandSolderingR1
1Conn_01x04Connectors_JST:JST_XH_S04B-XH-A_04x2.50mm_AngledJ1
1DHT11Pin_Headers:Pin_Header_Straight_1x04_Pitch2.54mmU1

The 3 most common of 5 parts.

More from tuankiet65/pnc-modules

12
  • 2 layers100.3 × 67.3 mmPnc modules, the printed circuit board in 3D

    Pnc modules

    tuankiet65/pnc-modules

    83 parts
  • 2 layers74.9 × 44.5 mmRelay 2x, the printed circuit board in 3D

    Relay 2x

    tuankiet65/pnc-modules

    19 parts
  • 2 layers36.8 × 41.3 mmEsp8266, the printed circuit board in 3D

    Esp8266

    tuankiet65/pnc-modules

    15 parts
  • 2 layers74.9 × 44.5 mmRelay 2x, the printed circuit board in 3D

    Relay 2x

    tuankiet65/pnc-modules

    13 parts
  • 2 layers62.9 × 34.3 mmRtc ds1307, the printed circuit board in 3D

    Rtc ds1307

    tuankiet65/pnc-modules

    8 parts
  • 2 layers50.8 × 26.7 mmRtc ds1307, the printed circuit board in 3D

    Rtc ds1307

    tuankiet65/pnc-modules

    8 parts
  • 2 layers41.3 × 25.4 mmServo, the printed circuit board in 3D

    Servo

    tuankiet65/pnc-modules

    6 parts
  • 2 layers36.2 × 16.5 mmBreakout i2c, the printed circuit board in 3D

    Breakout i2c

    tuankiet65/pnc-modules

    5 parts
  • 2 layers50.2 × 34.9 mmPir sensor, the printed circuit board in 3D

    Pir sensor

    tuankiet65/pnc-modules

    5 parts

Similar boards

  • 2 layers96.6 × 82.8 mmStarbie, the printed circuit board in 3D

    Starbie

    SharKingStudios/Starbie

    Half-Life Week 1 Example Project

    11 parts28MIT
  • 2 layers100 × 50 mmConveyor belt pcb, the printed circuit board in 3D

    Conveyor belt pcb

    lansidev/conveyor-belt

    Miniature 3D printed conveyor belt for simulation and fun working with sensors, all controllable with Raspberry Pi

    22 parts9MIT
  • 2 layers93 × 20 mmWiFi VFD, the printed circuit board in 3D

    WiFi VFD

    ciisaichan/WiFi-VFD

    开源的ESP8266驱动VFD屏电路,支持BiliBili粉丝数、时间、温度、湿度

    23 parts8MIT
  • 2 layersOpenMQTTGatewayPCB, the printed circuit board in 3D

    OpenMQTTGatewayPCB

    ebrithiljonas/OMG_PCB

    All in One PCB for the OpenMQTTGateway Project

    36 parts7GPL-3.0
  • 2 layers62 × 19.3 mmSniffingTrinket, the printed circuit board in 3D

    SniffingTrinket

    GeorgK/SniffingTrinket

    A room climate monitor using the Adafruit Trinket Pro

    23 parts6GPL-3.0
  • 2 layersArduino relay, the printed circuit board in 3D

    Arduino relay

    bhaskar9980/Guardian

    Guardian is an advanced, fully automated hydroponics system designed to optimize plant growth and maximize yield.

    58 parts5MIT
  • 2 layers100 × 43.5 mmFirefly, the printed circuit board in 3D

    Firefly

    Twistx77/Firefly

    Open WIFI-enabled RGB lamp with temperature, humidity, suspended air particles and eCO2 sensors.

    33 parts5GPL-3.0
  • 2 layers30.5 × 77.5 mmProyecto sensor temperatura, the printed circuit board in 3D

    Proyecto sensor temperatura

    unla-investigacion-desarrollo/ecosistema-iot

    Antes de desarrollar el sistema final, realizamos una etapa de exploración donde investigamos y experimentamos con las siguientes tecnologías:

    8 parts5

Questions

How big is the Dht11 PCB?

It measures 44.5 × 16.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Dht11 use?

5 parts, built around the DHT11. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Dht11 KiCad files?

From the tuankiet65/pnc-modules repository on GitHub, at the commit this page was made from: the board is schematic/dht11/dht11.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Dht11 design in my own project?

Its repository states no licence, so its author keeps all rights: ask tuankiet65 before reusing the design.