

BattleBot
- Size
- 60 × 60 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 45
- Nets
- 69
- Pads
- 217
- Tracks, vias
- 282, 135
- Pours
- 56
- Routed
- Yes
- KiCad
- KiCad 8.0 (file 20240108)
- Created
- 19 Sep 2024
- Updated
- 30 Sep 2024
Overview
BattleBot is an open-source printed circuit board by trhussain, from the trhussain/battlebot_pcb repository on GitHub. It is a 2-layer board of 60 × 60 mm with 45 parts on 69 nets, routed with 282 tracks and 135 vias.
It is built around the ESP32-S3-MINI-1-N8, XT30PW-F and TLV76601QWDRBRQ1, with the USB4105-GF-A and XT30PW-M among its other parts. Its parts include 11 resistors, 11 connectors, 9 capacitors, 3 diodes and 3 switches. It belongs with the ESP32 boards of this library.
Main components
5ESP32-S3-MINI-1-N8
SMD-104.5dBm -40℃~+85℃ 2.4GHz 20.5dBm 330mA 3V~3.6V 97mA Bluetooth5.0 ESP32-S3FN8 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD WiFi Modules ROHSEspressif SystemsWiFi ModulesXT30PW-F
UncategorisedAmass ElectronicsTLV76601QWDRBRQ1
WSON-8-EP(3x3)-40℃~+125℃@(Ta) 1 16V 500mA 50uA 60uVrms 70dB@(1kHz) 750mV@(500mA) 800mV~14.6V Adjustable Over Current Protection、Over Temperature Protection、Soft Start Positive WSON-8-EP(3x3) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSTexas InstrumentsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsUSB4105-GF-A
SMD-40℃~+85℃ 1 12P 48V 5A Black Female Surface Mount, Right Angle Type-C USB 2.0 SMD USB Connectors ROHSGlobal Connector Technology (GCT)USB ConnectorsXT30PW-M
-- Power connector / plug connector ROHSChangzhou Amass ElecUncategorised
Parts
45| Qty | Value | Footprint | References |
|---|---|---|---|
| 5 | 0.1uF | Capacitor_SMD:C_0805_2012Metric | C3, C4, C5, C11, C14 |
| 5 | Conn_01x02_Pin | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Horizontal | J2, J7, J8, J9, J10 |
| 4 | 10k | Resistor_SMD:R_0805_2012Metric | R4, R5, R12, R13 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3_DIN965 | H1, H2, H3, H4 |
| 4 | XT30PW-F | XT30PW-F:AMASS_XT30PW-F | J1, J4, J5, J6 |
| 2 | 1uF | Capacitor_SMD:C_0805_2012Metric | C2, C12 |
| 2 | 5.1k | Resistor_SMD:R_0805_2012Metric | R1, R2 |
| 2 | D | Diode_SMD:D_SOD-123F | D1, D3 |
| 2 | ~ | customFootprints:rockerSwitch-434133025816 | SW3, SW4 |
| 1 | 1k | Resistor_SMD:R_0805_2012Metric | R3 |
| 1 | 2.2uF | Capacitor_SMD:C_0805_2012Metric | C1 |
| 1 | 22uF | Capacitor_SMD:C_0805_2012Metric | C13 |
| 1 | 437k | Resistor_SMD:R_0805_2012Metric | R11 |
| 1 | 500k | Resistor_SMD:R_0402_1005Metric | R6 |
| 1 | 510 | Resistor_SMD:R_0805_2012Metric | R16 |
| 1 | 570k | Resistor_SMD:R_0805_2012Metric | R10 |
| 1 | ESP32-S3-MINI-1-N8 | esp32s3mini:XCVR_ESP32-S3-MINI-1-N8 | MCU1 |
| 1 | LED | LED_SMD:LED_0603_1608Metric | D2 |
| 1 | LSM6DSOXTR | LSM6DSOXTR:PQFN50P250X300X86-14N | Accelerometer1 |
| 1 | PMOS | Package_SO:PowerPAK_SO-8_Single | Q1 |
| 1 | SW_Nidec_CAS-120A1 | Button_Switch_SMD:SW_DPDT_CK_JS202011JCQN | SW2 |
| 1 | TLV76601QWDRBRQ1 | TLV76601:DRB0008J-IPC_A | LDO1 |
| 1 | USB4105-GF-A | USB4105-GF-A-Footprint:GCT_USB4105-GF-A | J11 |
| 1 | XT30PW-M | XT30PW-M:AMASS_XT30PW-M | J3 |
More from trhussain/battlebot_pcb
1- 2 layers60 × 60.8 mm

Similar boards
- 4 layers48.8 × 53.1 mm

ESC Board
FPV-Drone-STM32F411/DroneController
All-in-one FPV drone PCB with integrated flight controller, PDB, and ESCs built around STM32F411.
73 parts60 - 2 layers33.5 × 0.7 mm

- 4 layers99.5 × 69 mm

Pump controller reva
UWARG/pump-controller-hardware
Hardware for Competition 2026 Water Pump Controller on Project Valkyrie
244 parts - 4 layers71.8 × 40.1 mm

- 4 layers55.3 × 29 mm

Drone current sensor board
Kelvin-Ziqi-Zhao/drone-current-sensor-board
High current sensor board for battery+capacitor power supply system
66 parts7 - 2 layers45 × 30 mm

TFSBEC01
ThunderFly-aerospace/TFSBEC01
High efficient switching power supply for UAV actuators.
39 parts5GPL-3.0 - 2 layers82.5 × 26.5 mm

- 2 layers57 × 66 mm

Questions
How big is the BattleBot PCB?
It measures 60 × 60 mm and has 2 copper layers, 1.6 mm thick.
What parts does the BattleBot use?
45 parts, built around the ESP32-S3-MINI-1-N8, XT30PW-F, TLV76601QWDRBRQ1 and USB4105-GF-A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the BattleBot KiCad files?
From the trhussain/battlebot_pcb repository on GitHub, at the commit this page was made from: the board is BattleBot.kicad_pcb and its schematic BattleBot.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the BattleBot design in my own project?
Its repository states no licence, so its author keeps all rights: ask trhussain before reusing the design.