Skip to the content
2 layers35 × 128.5 mmMix, the printed circuit board in 3D

Mostly Eurorack projects

Size
35 × 128.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
30
Nets
14
Pads
64
Tracks, vias
145, 4
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
16 Jan 2021
Updated
19 Sep 2026

Overview

Mix is an open-source printed circuit board by tpcarlson, from the tpcarlson/synth-diy repository on GitHub. It is a 2-layer board of 35 × 128.5 mm with 30 parts on 14 nets, routed with 145 tracks and 4 vias.

It is built around the TL072. Its parts include 10 connectors, 8 resistors, 2 capacitors, 2 diodes and 1 IC. It belongs with the audio and music boards of this library.

Main components

1

README

vcadsr/README.md

VCADSR

What is this?

Voltage controlled ADSR, using the ElectricDruid EnvGen8 chip. The module provides voltage control over most parameters (Attack, decay, sustain, release, time, level) as well as manual control with sliders. There are also three switches for toggling the mode, linear/exponential, and a fifth stage called "punch" which adds a little bit more to the attack on an envelope.

The mode toggle switch allows for gated looping, just looping (Almost like an LFO), and normal ADSR mode.

How much power does it use?

As measured by the joranalogue Test 3, around 40mA on +12v and 30mA on -12v at peak. The 5v rail is unused.

Where does the design come from?

The schematic is really an extension of the reference design on the ElectricDruid site, with some changes to add LEDs, and cutting features that would otherwise take up more panel space than I was comfortable with - I dropped the attenuators for CV inputs in favour of nice big manual controls with linear potentiometers instead.

Are there any rare/weird parts used?

You'll need one of the EnvGen8 chips in order to make this function at all!

Are there any problems with the design?

Just a couple, which are corrected in the version here. First, the LEDs for gate and trigger had some issues drawing too much power due to an oversight in the schematic. As it turns out LEDs don't really like being driven without a resistor! Second, the panel design had the mode and linear/exponential graphics switched which makes operating it a little bit more confusing than it otherwise ought to be.

These problems are both fixed in the repository right now though, however the fixes are untested. If I make another run of these boards, I will verify that the fix worked and remove this whole section!

Do you have a BOM/Mouser cart/Tayda links?

Sorry, no. Things go out of stock so frequently it'd be a lot of work to keep these up to date. Everything in this project is easy to source though, so you should not have any trouble.

Other resources
  • Assembly instructions
  • Interactive BOM - This includes pre-soldered SMT parts as well as the through-hole parts. To use this, save the 'raw' view to your computer and open it in a web browser

Parts

30
QtyValueFootprintReferences
7100kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R2, R3, R4, R5, R6, R7
5AudioJack2Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHolesJ1, J2, J3, J4, J5
2100nCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC1, C2
2D_SchottkyDiode_THT:D_DO-41_SOD81_P7.62mm_HorizontalD1, D2
2OSHWSymbol:OSHW-Logo_5.7x6mm_SilkScreenJ27, J27
2WEEESymbol:WEEE-Logo_4.2x6mm_SilkScreenJ26, J26
11kResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR8
1Conn_02x05_Odd_EvenConnector_IDC:IDC-Header_2x05_P2.54mm_VerticalJ6
1TL072Package_DIP:DIP-8_W7.62mmU1

The 23 most common of 30 parts.

More from tpcarlson/synth-diy

12
  • 4 layers241.2 × 327.2 mmCyclic, the printed circuit board in 3D

    Cyclic

    tpcarlson/synth-diy

    Mostly Eurorack projects

    439 parts107
  • 2 layers293.3 × 128.5 mmTwoshot, the printed circuit board in 3D

    Twoshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    223 parts107
  • 4 layers179.5 × 128.5 mmSynth diy, the printed circuit board in 3D

    Synth diy

    tpcarlson/synth-diy

    Mostly Eurorack projects

    175 parts107
  • 4 layers313.1 × 185.6 mmOneshot, the printed circuit board in 3D

    Oneshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    172 parts107
  • 2 layers85.4 × 128.5 mmKinky lynx, the printed circuit board in 3D

    Kinky lynx

    tpcarlson/synth-diy

    Mostly Eurorack projects

    165 parts107
  • 2 layers286.9 × 128.7 mmLattice, the printed circuit board in 3D

    Lattice

    tpcarlson/synth-diy

    Mostly Eurorack projects

    161 parts107
  • 2 layers40.3 × 109.6 mmImpact main, the printed circuit board in 3D

    Impact main

    tpcarlson/synth-diy

    Mostly Eurorack projects

    159 parts107
  • 2 layers191.3 × 128.5 mmSycamore, the printed circuit board in 3D

    Sycamore

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 4 layers179.1 × 128.5 mmVcadsr, the printed circuit board in 3D

    Vcadsr

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 2 layers94.3 × 128.5 mmLeaky bucket, the printed circuit board in 3D

    Leaky bucket

    tpcarlson/synth-diy

    Mostly Eurorack projects

    137 parts107
  • 2 layers101.3 × 128.5 mm3-phase lfo, the printed circuit board in 3D

    3-phase lfo

    tpcarlson/synth-diy

    Mostly Eurorack projects

    129 parts107
  • 2 layers131.8 × 57.6 mmRowan, the printed circuit board in 3D

    Rowan

    tpcarlson/synth-diy

    Mostly Eurorack projects

    115 parts107

Similar boards

  • 2 layers148 × 84.5 mmPanel daisy, the printed circuit board in 3D

    Panel daisy

    ohmtech-rdi/eurorack-blocks

    Software to Hardware Prototyping for Eurorack using C++, Max/Gen~ or Faust

    259 parts410
  • 2 layers39.6 × 99.1 mmESP32-Eurorack Audio, the printed circuit board in 3D

    ESP32-Eurorack Audio

    ctag-fh-kiel/ctag-tbd

    CTAG TBD >>to be determined<< an extendible open source Eurorack sound module

    128 parts260
  • 4 layers121.9 × 109.2 mmPlinkyblack hwmidi jacks, the printed circuit board in 3D

    Plinkyblack hwmidi jacks

    plinkysynth/plinky_public

    a public release of the plinky sw and hw

    300 parts227
  • 2 layers58 × 110 mmVco core, the printed circuit board in 3D

    Vco core

    shmoergh/moduleur

    Fully analog DIY-friendly modular synth

    146 parts222
  • 2 layers37 × 113.9 mmVCO, the printed circuit board in 3D

    VCO

    nickajeglin/Eurorack-pcbs

    A collection of easy to solder DIY eurorack PCB's

    104 parts208
  • 2 layers111.3 × 106.4 mmSuper Sixteen v1, the printed circuit board in 3D

    Super Sixteen v1

    matthewcieplak/super-sixteen

    Code and schematics for the Super Sixteen Eurorack sequencer

    141 parts171
  • 2 layers85.1 × 62.2 mmMic extension board, the printed circuit board in 3D

    Mic extension board

    StoneRose35/cortexguitarfx

    guitar effects processor implemented on various arm cortex platforms

    75 parts146

Questions

How big is the Mix PCB?

It measures 35 × 128.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Mix use?

30 parts, built around the TL072. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Mix KiCad files?

From the tpcarlson/synth-diy repository on GitHub, at the commit this page was made from: the board is mix/mix.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Mix design in my own project?

Its repository states no licence, so its author keeps all rights: ask tpcarlson before reusing the design.