Skip to the content
2 layers35.1 × 103.1 mmLogic, the printed circuit board in 3D

Mostly Eurorack projects

Size
35.1 × 103.1 mm
Copper layers
2
Thickness
1.6 mm
Parts
95
Nets
69
Pads
255
Tracks, vias
643, 52
Pours
14
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
16 Jan 2021
Updated
19 Sep 2026

Overview

Logic is an open-source printed circuit board by tpcarlson, from the tpcarlson/synth-diy repository on GitHub. It is a 2-layer board of 35.1 × 103.1 mm with 95 parts on 69 nets, routed with 643 tracks and 52 vias.

It is built around the 1N4148W and MMBT3904. Its parts include 39 resistors, 28 diodes, 16 connectors, 6 capacitors and 4 transistors. It belongs with the audio and music boards of this library.

Main components

2

README

vcadsr/README.md

VCADSR

What is this?

Voltage controlled ADSR, using the ElectricDruid EnvGen8 chip. The module provides voltage control over most parameters (Attack, decay, sustain, release, time, level) as well as manual control with sliders. There are also three switches for toggling the mode, linear/exponential, and a fifth stage called "punch" which adds a little bit more to the attack on an envelope.

The mode toggle switch allows for gated looping, just looping (Almost like an LFO), and normal ADSR mode.

How much power does it use?

As measured by the joranalogue Test 3, around 40mA on +12v and 30mA on -12v at peak. The 5v rail is unused.

Where does the design come from?

The schematic is really an extension of the reference design on the ElectricDruid site, with some changes to add LEDs, and cutting features that would otherwise take up more panel space than I was comfortable with - I dropped the attenuators for CV inputs in favour of nice big manual controls with linear potentiometers instead.

Are there any rare/weird parts used?

You'll need one of the EnvGen8 chips in order to make this function at all!

Are there any problems with the design?

Just a couple, which are corrected in the version here. First, the LEDs for gate and trigger had some issues drawing too much power due to an oversight in the schematic. As it turns out LEDs don't really like being driven without a resistor! Second, the panel design had the mode and linear/exponential graphics switched which makes operating it a little bit more confusing than it otherwise ought to be.

These problems are both fixed in the repository right now though, however the fixes are untested. If I make another run of these boards, I will verify that the fix worked and remove this whole section!

Do you have a BOM/Mouser cart/Tayda links?

Sorry, no. Things go out of stock so frequently it'd be a lot of work to keep these up to date. Everything in this project is easy to source though, so you should not have any trouble.

Other resources
  • Assembly instructions
  • Interactive BOM - This includes pre-soldered SMT parts as well as the through-hole parts. To use this, save the 'raw' view to your computer and open it in a web browser

Parts

95
QtyValueFootprintReferences
18LEDLED_THT:LED_D3.0mmD2, D6, D11, D12, D14, D16, D17, D19, D21, D22, D23, D24, D25, D26, D27, D28 +2
161kResistor_SMD:R_0805_2012MetricR1, R6, R9, R11, R12, R13, R18, R20, R21, R24, R27, R29, R30, R33, R36, R38
132k7Resistor_SMD:R_0805_2012MetricR3, R8, R10, R16, R17, R19, R23, R26, R28, R32, R35, R37, R39
12AudioJack2Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHolesJ1, J3, J4, J5, J6, J7, J8, J9, J10, J11, J12, J13
9100kResistor_SMD:R_0805_2012MetricR2, R4, R7, R14, R15, R22, R25, R31, R34
81N4148WDiode_SMD:D_SOD-123D1, D5, D8, D10, D13, D15, D18, D20
4100nCapacitor_SMD:C_0805_2012MetricC3, C4, C5, C6
4MMBT3904Package_TO_SOT_SMD:SOT-23Q1, Q2, Q3, Q4
210uCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC1, C2
2Conn_01x07Connector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_VerticalJ16, J18
2D_SchottkyDiode_THT:D_A-405_P7.62mm_HorizontalD3, D4
2TL074Package_SO:SOIC-14_3.9x8.7mm_P1.27mmU1, U3
110kResistor_SMD:R_0805_2012MetricR5
1Conn_01x09Connector_PinHeader_2.54mm:PinHeader_1x09_P2.54mm_VerticalJ14
1Conn_02x05_Odd_EvenConnector_IDC:IDC-Header_2x05_P2.54mm_VerticalJ2

More from tpcarlson/synth-diy

12
  • 4 layers241.2 × 327.2 mmCyclic, the printed circuit board in 3D

    Cyclic

    tpcarlson/synth-diy

    Mostly Eurorack projects

    439 parts107
  • 2 layers293.3 × 128.5 mmTwoshot, the printed circuit board in 3D

    Twoshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    223 parts107
  • 4 layers179.5 × 128.5 mmSynth diy, the printed circuit board in 3D

    Synth diy

    tpcarlson/synth-diy

    Mostly Eurorack projects

    175 parts107
  • 4 layers313.1 × 185.6 mmOneshot, the printed circuit board in 3D

    Oneshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    172 parts107
  • 2 layers85.4 × 128.5 mmKinky lynx, the printed circuit board in 3D

    Kinky lynx

    tpcarlson/synth-diy

    Mostly Eurorack projects

    165 parts107
  • 2 layers286.9 × 128.7 mmLattice, the printed circuit board in 3D

    Lattice

    tpcarlson/synth-diy

    Mostly Eurorack projects

    161 parts107
  • 2 layers40.3 × 109.6 mmImpact main, the printed circuit board in 3D

    Impact main

    tpcarlson/synth-diy

    Mostly Eurorack projects

    159 parts107
  • 2 layers191.3 × 128.5 mmSycamore, the printed circuit board in 3D

    Sycamore

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 4 layers179.1 × 128.5 mmVcadsr, the printed circuit board in 3D

    Vcadsr

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 2 layers94.3 × 128.5 mmLeaky bucket, the printed circuit board in 3D

    Leaky bucket

    tpcarlson/synth-diy

    Mostly Eurorack projects

    137 parts107
  • 2 layers101.3 × 128.5 mm3-phase lfo, the printed circuit board in 3D

    3-phase lfo

    tpcarlson/synth-diy

    Mostly Eurorack projects

    129 parts107
  • 2 layers131.8 × 57.6 mmRowan, the printed circuit board in 3D

    Rowan

    tpcarlson/synth-diy

    Mostly Eurorack projects

    115 parts107

Similar boards

  • 4 layers99 × 53.3 mmPSLab, the printed circuit board in 3D

    PSLab

    fossasia/pslab-hardware

    PSLab Hardware Design and Schematics https://pslab.io

    199 parts1.7kApache-2.0
  • 6 layers160 × 100 mmAdrmu6layer, the printed circuit board in 3D

    Adrmu6layer

    marcoreps/ADRmu

    ADR1000 10V standard

    240 parts149
  • 2 layers60.2 × 106.5 mmTiNRS - DuckTape, the printed circuit board in 3D

    TiNRS - DuckTape

    ThisIsNotRocketScience/Eurorack-Modules

    This is not Rocket Science presents: Eurorack modular synthesizer modules!

    262 parts87MIT
  • 2 layers84 × 85 mmHbr mk2-rxtx, the printed circuit board in 3D

    Hbr mk2-rxtx

    afiskon/hbr-mk2

    All HF bands QRP CW/SSB transceiver

    239 parts76MIT
  • 2 layers447.8 × 139.3 mmA500KB, the printed circuit board in 3D

    A500KB

    HenrykRichter/A500KB

    Amiga 500 Custom Mechanical Keyboard

    250 parts46
  • 2 layers155 × 70 mmPayphone v1, the printed circuit board in 3D

    Payphone v1

    sdylewski/Analog-Redial

    A circuit board for old telephones to come back to life. Plug one or two phones in, and you can call the other phone, use bluetooth, connect to others via voip, and do a variety of other things with a plain old rotary…

    137 parts46
  • 2 layers109.4 × 108.5 mmQUAAD V1 1, the printed circuit board in 3D

    QUAAD V1 1

    mzourack/QUAAD

    quad 4-step Eurorack CV sequencer

    191 parts45
  • 2 layers80.9 × 108.2 mmVca, the printed circuit board in 3D

    Vca

    spielhuus/elektrophon

    Modular analog electro acoustic noise machine.

    179 parts32

Questions

How big is the Logic PCB?

It measures 35.1 × 103.1 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Logic use?

95 parts, built around the 1N4148W and MMBT3904. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Logic KiCad files?

From the tpcarlson/synth-diy repository on GitHub, at the commit this page was made from: the board is logic/main.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Logic design in my own project?

Its repository states no licence, so its author keeps all rights: ask tpcarlson before reusing the design.