Skip to the content
4 layers179.5 × 128.5 mmSynth diy, the printed circuit board in 3D

Mostly Eurorack projects

Size
179.5 × 128.5 mm
Copper layers
4
Thickness
1.6 mm
Parts
175
Nets
119
Pads
576
Tracks, vias
1,365, 147
Pours
13
Routed
Yes
KiCad
KiCad 6 (file 20211014)
Created
16 Jan 2021
Updated
19 Sep 2026

Overview

Synth diy is an open-source printed circuit board by tpcarlson, from the tpcarlson/synth-diy repository on GitHub. It is a 4-layer board of 179.5 × 128.5 mm with 175 parts on 119 nets, routed with 1,365 tracks and 147 vias.

It is built around the MAX7219ENG+, DS1882Z-050+ and MC78L05ABD, with the MC7905CT, TXS0108EPW and MMBT3904 among its other parts. Its parts include 38 resistors, 23 capacitors, 23 diodes, 13 connectors and 12 ICs. It belongs with the audio and music boards and the RP2040 boards of this library.

Main components

6

README

vcadsr/README.md

VCADSR

What is this?

Voltage controlled ADSR, using the ElectricDruid EnvGen8 chip. The module provides voltage control over most parameters (Attack, decay, sustain, release, time, level) as well as manual control with sliders. There are also three switches for toggling the mode, linear/exponential, and a fifth stage called "punch" which adds a little bit more to the attack on an envelope.

The mode toggle switch allows for gated looping, just looping (Almost like an LFO), and normal ADSR mode.

How much power does it use?

As measured by the joranalogue Test 3, around 40mA on +12v and 30mA on -12v at peak. The 5v rail is unused.

Where does the design come from?

The schematic is really an extension of the reference design on the ElectricDruid site, with some changes to add LEDs, and cutting features that would otherwise take up more panel space than I was comfortable with - I dropped the attenuators for CV inputs in favour of nice big manual controls with linear potentiometers instead.

Are there any rare/weird parts used?

You'll need one of the EnvGen8 chips in order to make this function at all!

Are there any problems with the design?

Just a couple, which are corrected in the version here. First, the LEDs for gate and trigger had some issues drawing too much power due to an oversight in the schematic. As it turns out LEDs don't really like being driven without a resistor! Second, the panel design had the mode and linear/exponential graphics switched which makes operating it a little bit more confusing than it otherwise ought to be.

These problems are both fixed in the repository right now though, however the fixes are untested. If I make another run of these boards, I will verify that the fix worked and remove this whole section!

Do you have a BOM/Mouser cart/Tayda links?

Sorry, no. Things go out of stock so frequently it'd be a lot of work to keep these up to date. Everything in this project is easy to source though, so you should not have any trouble.

Other resources
  • Assembly instructions
  • Interactive BOM - This includes pre-soldered SMT parts as well as the through-hole parts. To use this, save the 'raw' view to your computer and open it in a web browser

Parts

175
QtyValueFootprintReferences
19100nCapacitor_SMD:C_0805_2012MetricC1, C2, C3, C4, C5, C11, C13, C14, C16, C17, C18, C19, C20, C21, C22, C23 +3
16@HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0, @HOLE0
1610kResistor_SMD:R_0805_2012MetricR1, R2, R6, R14, R15, R16, R17, R21, R22, R23, R25, R26, R27, R31, R52, R53
16LEDLED_THT:LED_D3.0mmD2, D3, D4, D5, D6, D7, D15, D16, D17, D18, D19, D20, D21, D22, D23, D24
123.9kResistor_SMD:R_0805_2012MetricR9, R10, R11, R18, R19, R20, R28, R29, R30, R37, R38, R39
11AudioJack2Connector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHolesJ1, J2, J3, J4, J5, J7, J8, J9, J10, J11, J12
10MountingHole_6mmMountingHole:MountingHole_6mm2, 2, 2, 2, 2, 2, 2, 2, 2, 2
10SW_SPSTRS:SW_D6R90_F1_LFSSW1, SW2, SW3, SW4, SW5, SW6, SW7, SW8, SW9, SW10
71kResistor_SMD:R_0805_2012MetricR3, R4, R5, R32, R43, R44, R45
620kRS:SIP-3RV1, RV2, RV3, RV4, RV5, RV6
51N4148Diode_SMD:D_SOD-123D1, D11, D12, D13, D14
5MMBT3904Package_TO_SOT_SMD:SOT-23Q1, Q2, Q3, Q4, Q5
410uCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC12, C15, C24, C25
3TL074Package_SO:SOIC-14_3.9x8.7mm_P1.27mmU2, U3, U4
3ds1882z-050+RS:SOIC-16_4.55x10.3mm_P1.27mm_LONGPADSU7, U8, U9
24k7Resistor_SMD:R_0805_2012MetricR7, R8
2D_SchottkyDiode_THT:D_A-405_P7.62mm_HorizontalD9, D10
110kPotentiometer_THT:Potentiometer_Bourns_PTA6043_Single_SlideRV7
19.53kResistor_SMD:R_0805_2012MetricR24
1AudioJack2_SwitchTConnector_Audio:Jack_3.5mm_QingPu_WQP-PJ398SM_Vertical_CircularHolesJ13
1Conn_02x05_Odd_EvenConnector_IDC:IDC-Header_2x05_P2.54mm_VerticalJ6
1Jumper_3_Bridged12Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJP1
1KCSA02-107Display_7Segment:7SegmentLED_LTS6760_LTS6780U10
1MAX7219ENG+Package_SO:SOIC-24W_7.5x15.4mm_P1.27mmU6
1MC78L05Package_TO_SOT_THT:TO-92_Inline_WideU11
1MC7905Package_TO_SOT_THT:TO-92_Inline_WideU12
1PicoRasperry Pi Pico:RPi_Pico_SMD_THU1
1TXS0108EPWPackage_SO:TSSOP-20_4.4x6.5mm_P0.65mmU5

The 158 most common of 175 parts.

More from tpcarlson/synth-diy

12
  • 4 layers241.2 × 327.2 mmCyclic, the printed circuit board in 3D

    Cyclic

    tpcarlson/synth-diy

    Mostly Eurorack projects

    439 parts107
  • 2 layers293.3 × 128.5 mmTwoshot, the printed circuit board in 3D

    Twoshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    223 parts107
  • 4 layers313.1 × 185.6 mmOneshot, the printed circuit board in 3D

    Oneshot

    tpcarlson/synth-diy

    Mostly Eurorack projects

    172 parts107
  • 2 layers85.4 × 128.5 mmKinky lynx, the printed circuit board in 3D

    Kinky lynx

    tpcarlson/synth-diy

    Mostly Eurorack projects

    165 parts107
  • 2 layers286.9 × 128.7 mmLattice, the printed circuit board in 3D

    Lattice

    tpcarlson/synth-diy

    Mostly Eurorack projects

    161 parts107
  • 2 layers40.3 × 109.6 mmImpact main, the printed circuit board in 3D

    Impact main

    tpcarlson/synth-diy

    Mostly Eurorack projects

    159 parts107
  • 2 layers191.3 × 128.5 mmSycamore, the printed circuit board in 3D

    Sycamore

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 4 layers179.1 × 128.5 mmVcadsr, the printed circuit board in 3D

    Vcadsr

    tpcarlson/synth-diy

    Mostly Eurorack projects

    149 parts107
  • 2 layers94.3 × 128.5 mmLeaky bucket, the printed circuit board in 3D

    Leaky bucket

    tpcarlson/synth-diy

    Mostly Eurorack projects

    137 parts107
  • 2 layers101.3 × 128.5 mm3-phase lfo, the printed circuit board in 3D

    3-phase lfo

    tpcarlson/synth-diy

    Mostly Eurorack projects

    129 parts107
  • 2 layers131.8 × 57.6 mmRowan, the printed circuit board in 3D

    Rowan

    tpcarlson/synth-diy

    Mostly Eurorack projects

    115 parts107
  • 2 layers81.1 × 128.5 mmMultimult, the printed circuit board in 3D

    Multimult

    tpcarlson/synth-diy

    Mostly Eurorack projects

    113 parts107

Similar boards

  • 2 layers55.9 × 78.7 mmCEM3340 VCO, the printed circuit board in 3D

    CEM3340 VCO

    JordanAceto/CEM3340_VCO

    PCB for a CEM3340 based VCO with sine, triangle, saw, and pulse waves.

    96 parts4CC-BY-4.0
  • 2 layers247 × 140 mmPsu board, the printed circuit board in 3D

    Psu board

    aeberbach/ReAnalog

    Replacing the PSU, CRT and analog board in Macintosh SE and SE/30

    11 parts1
  • 2 layers149.9 × 55.9 mmPc amplifier, the printed circuit board in 3D

    Pc amplifier

    dilshan/arduino-mini-amp

    Arduino based stereo audio amplifier system

    140 parts67MIT
  • 2 layers61 × 41.3 mmFocuser, the printed circuit board in 3D

    Focuser

    AndreasFMueller/Focuser

    The motor focus driver from starizona is quite feature complete, more so than many other devices, but it is very large and heavy.

    24 partsGPL-3.0
  • 2 layers27.9 × 40.6 mmTracker, the printed circuit board in 3D

    Tracker

    AndreasFMueller/Tracker

    astronomical tracker device for long exposure photographs with a simple camera

    16 parts
  • 2 layers100 × 100 mmIo card, the printed circuit board in 3D

    Io card

    czalinski/ThlHats

    Test devices with Raspberry PI HAT form factor

    139 partsMIT
  • 4 layers80 × 100 mmBaseboard, the printed circuit board in 3D

    Baseboard

    NVIDIA-AI-IOT/my-jetson-nano-baseboard

    An open source Jetson Nano baseboard and tools to design your own.

    240 parts91
  • 2 layers155 × 75 mmHacklock-2137, the printed circuit board in 3D

    Hacklock-2137

    p-durlej/hswaw-hscloud

    Controller board for next gen hacklock door / lock / access control system.

    119 parts

Questions

How big is the Synth diy PCB?

It measures 179.5 × 128.5 mm and has 4 copper layers, 1.6 mm thick.

What parts does the Synth diy use?

175 parts, built around the MAX7219ENG+, DS1882Z-050+, MC78L05ABD and MC7905CT. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Synth diy KiCad files?

From the tpcarlson/synth-diy repository on GitHub, at the commit this page was made from: the board is d6/d6.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the Synth diy design in my own project?

Its repository states no licence, so its author keeps all rights: ask tpcarlson before reusing the design.