
Divergence meter top
toohka42/Divergence-Meter
Itron Divergence meter based on Steins;Gate anime series

Itron Divergence meter based on Steins;Gate anime series
Divergence meter logic is an open-source printed circuit board by toohka42, from the toohka42/Divergence-Meter repository on GitHub, published under the MIT licence. It is a 2-layer board of 137.7 × 56.4 mm with 73 parts on 83 nets, routed with 650 tracks and 78 vias.
It is built around the BC547, 74HC595 and ULN2803A. Its parts include 16 resistors, 16 diodes, 16 transistors, 8 capacitors and 4 switches. It belongs with the AVR (ATmega, ATtiny) boards of this library.
readme is in process of writing, the same as the codeIn this project I am trying to build working prototype of Divergence meter that appeared in Steins;Gate anime series and Visual novels.

I use arduino board in combination with shift registers SN74HC595N to drive itrons IV-6.
| Itron No. | byte value |
|---|---|
| first | B01111111 |
| second | B10111111 |
| third | B11011111 |
| fourth | B11101111 |
| fifth | B11110111 |
| sixth | B11111011 |
| seventh | B11111101 |
| eighth | B11111110 |
| Number | byte value |
|---|---|
| zero | B00000011 |
| one | B10011111 |
| two | B00100101 |
| three | B00001101 |
| four | B10110001 |
| five | B01001001 |
| six | B01000001 |
| seven | B00011111 |
| eight | B00000001 |
| nine | B00001001 |
| symbol | byte value |
|---|---|
| dot | B11111110 |
| stroke | B11111101 |
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 100k | Resistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P2.54mm_Vertical | R1, R2, R3, R4, R5, R6, R7, R8, R9, R10, R11, R12, R13, R14, R15, R16 |
| 16 | 1N4148 | Diode_THT:D_DO-35_SOD27_P2.54mm_Vertical_KathodeUp | D1, D2, D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13, D14, D15, D16 |
| 16 | BC547 | Package_TO_SOT_THT:TO-92_Inline | Q1, Q2, Q3, Q4, Q5, Q6, Q7, Q8, Q9, Q10, Q11, Q12, Q13, Q14, Q15, Q16 |
| 5 | 100n | Capacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mm | C4, C5, C6, C7, C8 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.5mm_Pad_Via | H1, H2, H3, H4 |
| 4 | SW_Push | Button_Switch_THT:SW_PUSH_6mm_H4.3mm | SW1, SW2, SW3, SWR1 |
| 2 | 100u | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C1, C2 |
| 2 | 74HC595 | Package_DIP:DIP-16_W7.62mm_Socket | UR1, UR2 |
| 2 | ULN2803A | Package_DIP:DIP-18_W7.62mm_Socket | UT1, UT2 |
| 1 | 10u | Capacitor_THT:CP_Radial_D5.0mm_P2.00mm | C3 |
| 1 | Arduino_Nano_v3.x | Module:Arduino_Nano | A1 |
| 1 | Conn_01x06 | Connector_PinSocket_2.54mm:PinSocket_1x06_P2.54mm_Horizontal | JRTC1 |
| 1 | Conn_01x08 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Horizontal | JPWR1 |
| 1 | Conn_01x08 | Connector_PinSocket_2.54mm:PinSocket_1x08_P2.54mm_Vertical | JL2 |
| 1 | Conn_01x12 | Connector_PinSocket_2.54mm:PinSocket_1x12_P2.54mm_Vertical | J1 |

toohka42/Divergence-Meter
Itron Divergence meter based on Steins;Gate anime series


CatoLynx/LAWO-Arduino
Arduino Nano adapter board for LAWO XY5 flipdot displays

anshukumar146/GitHub
A compact, self-contained development board for the 8051 microcontroller family (AT89x51xxP), designed in KiCad — built to run 8051 firmware on the bench with nothing more than a barrel-jack power supply and a…


OverInvented/Flippy
The code needed to build a mechanical 7-segment display that uses electromagnets to display characters



It measures 137.7 × 56.4 mm and has 2 copper layers, 1.6 mm thick.
73 parts, built around the BC547, 74HC595 and ULN2803A. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the toohka42/Divergence-Meter repository on GitHub, at the commit this page was made from: the board is PCB/divergence_meter_logic/divergence_meter_logic.kicad_pcb and its schematic PCB/divergence_meter_logic/divergence_meter_logic.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).