

STM32N6 Thesis Board
Herzlich willkommen zum Repo des Robotersarmes der Arbeitsgruppe. Bitte beachtet, dass es sich hierbei handelt um eine Erweiterung bereits vorhandener Infrastruktur.
- Size
- 62.3 × 94.3 mm
- Copper layers
- 4
- Thickness
- 1.58 mm
- Parts
- 221
- Nets
- 273
- Pads
- 1,025
- Tracks, vias
- 2,880, 462
- Pours
- 37
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 29 Jul 2026
- Updated
- 12 Sep 2026
Overview
STM32N6 Thesis Board is an open-source printed circuit board by tobiasbaas, from the tobiasbaas/Roboterarm1 repository on GitHub. It is a 4-layer board of 62.3 × 94.3 mm with 221 parts on 273 nets, routed with 2,880 tracks and 462 vias.
It is built around the ST1S31PUR, ESDALC6V1W5 and LD1117S33TR(MS), with the LD1117S50TR(MS), LD39020ADTPU18R and LD39020ADTPU33R among its other parts. Its parts include 95 capacitors, 60 resistors, 19 diodes, 11 ICs and 8 connectors. It belongs with the STM32 boards of this library.
Main components
12ST1S31PUR
QFN-8(3x3)-40℃~+150℃@(TJ) 1 1.9MHz 2.8V~5.5V 3A 630uA 800mV~5.5V Adjustable Buck Built-in Overcurrent Protection、Light load efficient mode、Operating status indication、Cycle-by-cycle current limiting Step-down type Yes QFN-8(3x3) DC-DC Converters ROHSSTMicroelectronicsDC-DC ConvertersESDALC6V1W5
SOT-323-5-40℃~+150℃ 1uA 25W 3V 6.1V 6.1V 7.5pF Four channels IEC 61000-4-2 TVS Unidirectional SOT-323-5 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)LD1117S33TR(MS)
SOT-223-20℃~+125℃@(Ta) 1 1.4V@(1A) 12V 1A 2mA 3.3V Fixed Over Temperature Protection Positive SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMSKSEMIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLD1117S50TR(MS)
SOT-223-20℃~+125℃@(Ta) 1 1.4V@(1A) 12V 1A 2mA 4.9V~5.1V Fixed Positive Thermal Shutdown SOT-223 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMSKSEMIVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLD39020ADTPU18R
DFN-4(1x1)-40℃~+125℃@(Tj) 1 1.8V 100uA 200mA 350mV@(200mA) 45uVrms 5.5V 80dB@(1kHz) Fixed Over Current Protection、Thermal shutdown、Enable control、Output discharge、Built-in soft-start Positive DFN-4(1x1) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLD39020ADTPU33R
DFN-4(1x1)-40℃~+125℃@(Tj) 1 100uA 200mA 200mV@(200mA) 3.3V 45uVrms 5.5V 80dB Fixed Over Current Protection、Thermal Shutdown、Enable control Positive DFN-4(1x1) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsLD56100DPU18R
DFN-8(1.2x1.6)-40℃~+125℃@(Tj) 1 1.8V 13uVrms 155uA 1A 285mV@(1A) 5.5V 70dB@(1kHz) Fixed Over Current Protection、Over Temperature Protection、Soft Start、Short Circuit Protection Positive DFN-8(1.2x1.6) Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSSTMicroelectronicsVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsMX25UM51245GXDI00-TR
-- Lack of specifications ROHSMXICUncategorisedESDALC6V1-1U2
0201-40℃~+125℃ 1 100nA 12pF 20W@8/20us 2A@8/20us 3V 6.1V 8V ESD IEC 61000-4-2 Unidirectional 0201 ESD and Surge Protection (TVS/ESD) ROHSSTMicroelectronicsESD And Surge Protection (TVS/ESD)ECMF2-40A100N6
QFN-6L-55℃~+125℃ 10.7GHz 100mA 15dB@2.4GHz、17dB@6GHz、21dB@5GHz 2 3Ω 400fF 5V Yes QFN-6L EMI/RFI Filters (LC, RC Networks) ROHSSTMicroelectronicsEMI/RFI Filters (LC, RC Networks)KG EELP41.22-PHRH-35-A8J8-20-R18
SMDSMD LED Indication - Discrete ROHSOSRAM Opto SemiconLED Indication - DiscreteBSR14
SOT-23-55℃~+150℃ 1 NPN 10nA 1V 300MHz 35 350mW 40V 6V 800mA NPN SOT-23 Bipolar (BJT) ROHSonsemiBipolar (BJT)
README
README.mdKonzeption und Realisierung eines Edge-KI-Systems zur visuellen Posenschätzung eines Roboterarms
Herzlich willkommen zum Repo des Robotersarmes der Arbeitsgruppe. Bitte beachtet, dass es sich hierbei handelt um eine Erweiterung bereits vorhandener Infrastruktur. Für mehr Infos siehe das bisherige Github Repo:
Sowie als auch das offiziele Wiki zu den vergangegen Projekten im Ilias:
In dieser Readme wird der Gesamte Aufbau des Roboterarmes inklusive der Erweiterung, die im Rahmen der Bachelorthesis durchgeführt wurden, erläutert. Es soll einen Schnelleinstieg ermöglichen, indem ihr den Roboter mithilfe des RaspberryPI, STM32N6 Board und eurem Laptop bewegen könnt. Für tieferes Verständis des Projektes navigiert in die Unterordner des Repo.
1. Systemübersicht
Drei Geräte arbeiten zusammen. Der Laptop ist der Taktgeber, er steuert den Roboter und löst die Bildaufnahme aus.
┌──────────────────────────────┐
│ Laptop (Windows) │
│ capture_image.py │
└───────┬──────────────┬───────┘
│ │
UDP (WLAN) │ │ USB CDC (virtueller COM-Port)
4x float32 │ │ Kommandos: PING / TEST / CAPTURE
Winkel [rad] │ │ Antwort: Bild 640x480 RGB565
▼ ▼
┌───────────────────┐ ┌──────────────────────────┐
│ Raspberry Pi │ │ STM32N6570-DK │
│ ROS2 + UDP-Bridge │ │ Kamera IMX335 + NPU │
│ CAN-Bus │ │ Live-Bild auf LCD │
└────────┬──────────┘ └──────────────────────────┘
│ CAN
▼
┌──────────────┐
│ Roboterarm │ Open-Loop, 4 Gelenke, keine Encoder
└──────────────┘Warum dieser Aufbau? Der Roboterarm ist ein Open-Loop-System, es gibt keine Rotary-Encoder oder Hallsensoren, die den tatsächlichen Winkel zurückmelden. Für das KI-Training muss aber jedes Bild exakt zu einem bekannten Winkelsatz gehören. Deshalb wird der Roboter nicht über RViz von Hand bewegt, sondern von einem eigenen Python-Skript auf eine bekannte Zielpose gefahren. Das Skript wartet, bis die Bewegung sicher abgeschlossen ist, löst dann die Bildaufnahme aus und schreibt Bild und Winkel gemeinsam in eine CSV-Datei. Eine korrekt angefahrene Nullposition ist dabei die Grundvoraussetzung.
2. Repository-Struktur
.
├── 02_Software/
│ ├── Beachlor_Thesis_AI/ # KI-Pipeline (Training, Datenaufbereitung, Export)
│ ├── Image_Capture_Python/ # Host-Skripte: Trainingsdatenaufnahme (nur zusammen mit STM)
│ ├── New_Image_Capture/ # STM32-Firmware: Trainingsdatenaufnahme (Echte Bilder)
│ └── Thesis_Robot_Pose/ # STM32-Firmware: zusätzlich KI-Inferenz auf der NPU
├── 03_Hardware/
│ ├── STM32N6_Thesis_Board/ # Eigenes KiCad-Board (STM32N657X0H3Q)
│ └── Nucleo_PCB_FIles/ # Altium-Daten des MB1940-Referenzdesigns
└── README.md # diese Datei3. Schellstart
3.1 Voraussetzungen
Hardware
| Komponente | Anmerkung |
|---|---|
| Roboterarm mit CAN-Anbindung | 4 angesteuerte Gelenke |
| Raspberry Pi | ROS2 im Docker-Image, CAN-HAT |
| STM32N6570-DK | Kamera IMX335, LCD RK050HR18 |
| Laptop | Windows, MAC |
[!IMPORTANT] Bittet achtet darauf, dass euer Laptop und der Raspberry im selben Netzwerk miteinander verbunden sind!
Software auf dem Laptop
Falls ihr noch kein Python auf euren Laptop verwendet habt, so installiert zuerst Miniconda (https://www.anaconda.com/download/success) und erstellt ein Custom Environment für dieses Projekt.
Dazu öffnet ihr das Anaconda Powershell und gibt folgenden Commands nacheinander in das Terminal ein:
conda create --name Euer_Env_Name python=3.14conda activate Euer_Env_Namepip install ultralytics==8.4.146 torch==2.14.0 onnx==1.22.0 onnxruntime==1.29.0 opencv-python==5.0.0.93 numpy==2.4.6 pillow==12.3.0 pandas==3.0.5 matplotlib==3.11.1 pyserial==3.5 notebook==7.6.2 label-studio==1.23.0Zusätzlich benötigt ihr für die Inbetriebnahme des STM32N6 Boards die folgende Software von ST-Microelectronics:
- STM32 VsCode Extension (https://www.st.com/content/st_com/en/campaigns/stm32-vs-code-extension-z11.html)
- STM32 Cube CLT (https://www.st.com/en/development-tools/stm32cubeclt.html)
- STM32 Cube Programmer (https://www.st.com/en/development-tools/stm32cubeprog.html)
- STM32Cube AI Studio (https://www.st.com/content/st_com/en/campaigns/edge-ai-toolchain-for-mcus-z14.html)
3.2 Schritt 1: Roboter am Raspberry Pi starten
[!IMPORTANT] Das Passwort für den Pi selber und der Ausführung des Codes lautet:
ubuntu.
Auf dem Raspberry Pi genügt ein Terminal und ein Befehl. Alle Docker-Workspaces werden dabei im Hintergrund initialisiert:
./boot_robot.shDamit werden gestartet:
- CAN-Bus
- ROS2 inklusive aktiver UDP-Bridge
Nachdem alles initialisiert hat, kann der Roboter bereits gesteuert werden über RViz. Für mehr Infos zum
starten von RViz, schaut im oben verlinkten GitHub Repo nach.
Optional, um die CAN-Nachrichten live mitzulesen (zweites Terminal, erst nach dem Start des Roboters):
candump can0[!IMPORTANT] Den Roboter niemals gleichzeitig über RViz und über das Python-Skript ansprechen.
3.3 Schritt 2: STM32N6570-DK vorbereiten
- Boot-Pins BOOT0 und BOOT1 auf Low setzen (Flash-Mode, bevorzugte Betriebsart).
- FSBL und Appli in der CubeIDE bauen.
- Beide
.bin-Dateien signieren, siehe Abschnitt 4. - External Flash löschen, dann erst FSBL, danach Appli flashen.
- Board per USB an den Laptop stecken. Es meldet sich als virtueller COM-Port und sendet
nach der Enumeration dreimal
READY.
Für die reine Datenaufnahme wird 02_Software/New_Image_Capture geflasht.
3.4 Schritt 3: Bildaufnahme starten
In 02_Software/Image_Capture_Python/capture_image.py oben die Konfiguration prüfen:
COM_PORT = "COM4" # COM-Port des STM32 im Gerätemanager nachsehen
UDP_IP = "192.168.4.152" # IP des Raspberry Pi
UDP_PORT = 5005
num_positions = 1000 # Anzahl aufzunehmender PosenDann starten:
cd 02_Software/Image_Capture_Python
python capture_image.pyAblauf pro Bild: Zielpose per UDP senden, 4 s warten, CAPTURE über USB senden,
Bild empfangen, als PNG speichern, Zeile in labels.csv schreiben.
Ergebnis liegt in dataset/images/<lauf_zeitstempel>/pose_XXXX.png plus dataset/labels.csv.
4. Firmware flashen: Signierung
Der STM32N6 führt nur signierte Images aus. FSBL und Appli müssen getrennt signiert
werden.
[!IMPORTANT] Das Skript
sign_binaries.batim jeweiligen Firmware-Projekt automatisiert die folgenden Schritte.
1. In der CubeIDE beide Umgebungen bauen. Die `.bin` liegt im `Debug`-Ordner des jeweiligen Projekts. 2. Eingabeaufforderung öffnen und in dieses Verzeichnis wechseln:
cd /d <Pfad zum Debug-Ordner>-
Signieren:
bat STM32_SigningTool_CLI.exe -bin <name>.bin -t fsbl -la 0x80000000 -hv 2.3 -nk -o <name>-trusted.bin -align -dump <name>-trusted.binDas Ergebnis der Signierung steht ganz oben in der Ausgabe, nicht am Ende.
-
Die entstandene
*-trusted.binmit dem STM32CubeProgrammer flashen. Reihenfolge: External Flash löschen, dann FSBL, dann Appli.
5. Schnittstellen im Detail
5.1 Laptop zu Raspberry Pi (UDP)
| Eigenschaft | Wert |
|---|---|
| Protokoll | UDP, unidirektional (Laptop sendet) |
| Ziel | 192.168.4.152:5005 |
| Nutzdaten | 4 x float32, Big-Endian (struct Format !4f) |
| Einheit | Radiant, Reihenfolge Joint 1 bis Joint 4 |
| Gelenkgrenzen | J1 -95° bis 95°, J2 0° bis 95°, J3 -80° bis 80°, J4 -10° bis 50° |
Vor dem Start fährt das Skript dreimal die Nullposition [0,0,0,0] an und wartet 4 s.
Änderung am Raspberry Pi: Die UDP-Bridge wurde in
robot_moveit_config/launch/planning_execution.launch.py ergänzt. Die betroffenen Stellen
sind in der Datei markiert, weitere Anpassungen sind für Folgeprojekte nicht nötig.
Aktiviert wird sie über den Launch-Parameter:
ros2 launch robot_moveit_config planning_execution.launch.py use_udp_bridge:=trueboot_robot.sh setzt diesen Parameter bereits. Der normale ROS2-Workflow bleibt
unverändert, RViz funktioniert weiterhin (aber nicht gleichzeitig, siehe Warnung oben).
6. Troubleshooting
| Symptom | Ursache und Abhilfe |
|---|---|
capture_image.py bleibt bei "Warte auf Lebenszeichen" | Board sendet kein READY. Board resetten, COM-Port im Gerätemanager prüfen, ggf. Firmware nicht korrekt geflasht |
| Roboter reagiert nicht auf UDP | boot_robot.sh gestartet? UDP-Bridge aktiv? Laptop und Pi im selben WLAN? IP in capture_image.py korrekt? |
| Roboter fährt ruckartig oder unvorhersehbar | RViz läuft parallel. Nur eine Steuerquelle gleichzeitig verwenden |
| Bilder und Winkel passen nicht zusammen | Nullposition nicht korrekt angefahren, oder Wartezeit nach der Bewegung zu kurz |
| Board startet nach dem Flashen nicht | Signierung fehlt oder falsche Reihenfolge. External Flash löschen, erst FSBL, dann Appli |
| Bild kommt unvollständig an | CAPTURE_TIMEOUT erhöhen, anderes USB-Kabel oder anderen Port verwenden |
Parts
221| Qty | Value | Footprint | References |
|---|---|---|---|
| 24 | 100n | Capacitor_SMD:C_0201_0603Metric | C11, C12, C13, C14, C15, C16, C17, C18, C19, C20, C21, C22, C23, C24, C25, C26 +8 |
| 15 | 22u | Capacitor_SMD:C_0603_1608Metric | C51, C52, C53, C54, C55, C56, C59, C100, C101, C102, C106, C107, C108, C109, C112 |
| 13 | 0 | Resistor_SMD:R_0603_1608Metric | R6, R9, R45, R47, R48, R58, R60, R61, R62, R63, R64, R65, R66 |
| 12 | 1u | Capacitor_SMD:C_0201_0603Metric | C10, C28, C32, C33, C34, C35, C36, C37, C38, C39, C40, C41 |
| 11 | ESDALC6V1-1U2 | ESDALC6V1-1U2:ESDALC6V11U2 | D3, D4, D5, D6, D7, D8, D9, D10, D11, D12, D13 |
| 9 | 10u | Capacitor_SMD:C_0603_1608Metric | C58, C71, C72, C89, C90, C98, C99, C104, C111 |
| 9 | 1u | Capacitor_SMD:C_0603_1608Metric | C73, C91, C92, C93, C95, C96, C97, C103, C110 |
| 8 | 10k | Resistor_SMD:R_0603_1608Metric | R1, R2, R5, R20, R27, R32, R41, R42 |
| 5 | 22u | Capacitor_SMD:C_0402_1005Metric | C30, C31, C42, C43, C44 |
| 5 | 330 | Resistor_SMD:R_0603_1608Metric | R38, R39, R40, R56, R57 |
| 4 | 100n | Capacitor_SMD:C_0603_1608Metric | C1, C2, C5, C68 |
| 4 | ECMF2-40A100N6 | ECMF2-40A100N6:ECMF240A100N6 | FL1, FL2, FL3, FL4 |
| 4 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_Pad_Via | H1, H2, H3, H4 |
| 3 | 100k | Resistor_SMD:R_0603_1608Metric | R21, R26, R35 |
| 3 | 24k | Resistor_SMD:R_0603_1608Metric | R22, R52, R55 |
| 3 | 4.7u | Capacitor_SMD:C_0603_1608Metric | C3, C4, C6 |
| 3 | ESDALC6V1W5 | ESDALC6V1W5:SOT65P210X110-5N | IC3, IC6, IC13 |
| 3 | KG_EELP41.22-PHRH-35-A8J8-20-R18 | KG_EELP41.22-PHRH-35-A8J8-20-R18:KGEELP4122PHRH35A8J820R18 | LED1, LED2, LED6 |
| 2 | 1.3M | Resistor_SMD:R_0603_1608Metric | R23, R25 |
| 2 | 1.5k | Resistor_SMD:R_0603_1608Metric | R18, R19 |
| 2 | 2.2p | Capacitor_SMD:C_0603_1608Metric | C61, C62 |
| 2 | 200 | Resistor_SMD:R_0603_1608Metric | R36, R37 |
| 2 | 22m | Resistor_SMD:R_0603_1608Metric | R24, R33 |
| 2 | 330m | Resistor_SMD:R_0603_1608Metric | R16, R50 |
| 2 | 330p | Capacitor_SMD:C_0603_1608Metric | C66, C67 |
| 2 | 47k | Resistor_SMD:R_0603_1608Metric | R28, R34 |
| 2 | 50m | Resistor_SMD:R_0603_1608Metric | R14, R15 |
| 2 | 74404043022A | 74404043022A:INDPM4040X250N | L4, L5 |
| 2 | 8.2p | Capacitor_SMD:C_0603_1608Metric | C63, C64 |
| 2 | BSR14 | BSR14:SOT95P240X120-3N | Q3, Q4 |
| 2 | Conn_01x03 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J5, J6 |
| 2 | KSC721J_LFS | KSC721J_LFS:KSC721JLFS | S1, S2 |
| 2 | LS_R976-NR-1 | LS_R976-NR-1:LEDC2012X40N | LED3, LED5 |
| 2 | ST1S31PUR | ST1S31PUR:SON65P300X300X100-9N-D | IC8, IC9 |
| 2 | STL40DN3LLH5 | STL40DN3LLH5:STL40DN3LLH5 | Q2, Q5 |
| 1 | 0 | Resistor_SMD:R_0402_1005Metric | R3 |
| 1 | 10 | Capacitor_SMD:C_0603_1608Metric | C57 |
| 1 | 10n | Capacitor_SMD:C_0603_1608Metric | C70 |
| 1 | 10p | Capacitor_SMD:C_0603_1608Metric | C69 |
| 1 | 12401826E412A | 12401826E412A:12401826E412A | J4 |
| 1 | 140k | Resistor_SMD:R_0603_1608Metric | R31 |
| 1 | 150k | Resistor_SMD:R_0603_1608Metric | R12 |
| 1 | 160k | Resistor_SMD:R_0603_1608Metric | R10 |
| 1 | 1M | Resistor_SMD:R_0603_1608Metric | R13 |
| 1 | 2-1734592-2 | 2-1734592-2:217345922 | J7 |
| 1 | 2.2n | Capacitor_SMD:C_0201_0603Metric | C9 |
| 1 | 2.2u | Capacitor_SMD:C_0603_1608Metric | C65 |
| 1 | 220u | Capacitor_SMD:C_0603_1608Metric | C60 |
| 1 | 22k | Resistor_SMD:R_0603_1608Metric | R29 |
| 1 | 22p | Capacitor_SMD:C_0603_1608Metric | C105 |
| 1 | 270 | Resistor_SMD:R_0603_1608Metric | R30 |
| 1 | 30k | Resistor_SMD:R_0603_1608Metric | R54 |
| 1 | 4.7u | Capacitor_SMD:C_0201_0603Metric | C8 |
| 1 | 422k | Resistor_SMD:R_0603_1608Metric | R11 |
| 1 | 50m | Resistor_SMD:R_0402_1005Metric | R7 |
| 1 | 560 | Resistor_SMD:R_0603_1608Metric | R53 |
| 1 | 74479276168 | Inductor_SMD:L_0805_2012Metric | L2 |
| 1 | 750m | Resistor_SMD:R_0603_1608Metric | R49 |
| 1 | 75k | Resistor_SMD:R_0603_1608Metric | R51 |
| 1 | 820 | Resistor_SMD:R_0603_1608Metric | R17 |
| 1 | ABM12W-48.0000MHZ-7-D1X-T3 | ABM12W-24.0000MHZ-6-D1X-T3:ABM12W300000MHZ6B1UT3 | Y2 |
| 1 | BAT60JFILM | BAT60JFILM:SOD2513X117N | D1 |
| 1 | CM7V-T1A-32.768KHZ-6PF-20PPM-TA-QC | CM7V-T1A-32.768KHZ-6PF-20PPM-TA-QC:CM7V32768TBQA020 | Y3 |
| 1 | Conn_02x02_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J3 |
| 1 | Conn_02x07_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x07_P2.54mm_Vertical | J1 |
| 1 | Conn_02x10_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_Vertical | J2 |
| 1 | DFE201612P-R24M=P2 | DFE201612P-R24M=P2:1286ASH1R0MP2 | L6 |
| 1 | ESDA25P35-1U1M | ESDA25P35-1U1M:ESDA25P351U1M | D2 |
| 1 | FBMJ1608HM180NTR | Inductor_SMD:L_0603_1608Metric | L1 |
| 1 | LB_Q39G-L2OO-35-1 | LB_Q39G-L2OO-35-1:LEDC1608X40N | LED4 |
| 1 | LD1117S33TR | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U3 |
| 1 | LD1117S50TR | LD1117S50TR:SOT230P700X190-4N | IC11 |
| 1 | LD39020ADTPU18R | Package_DFN_QFN:OnSemi_XDFN4-1EP_1.0x1.0mm_EP0.52x0.52mm | U2 |
| 1 | LD39020ADTPU33R | Package_DFN_QFN:OnSemi_XDFN4-1EP_1.0x1.0mm_EP0.52x0.52mm | U1 |
| 1 | LD56100DPU18R | LD56100DPU18R:LD56100DPU18R | IC7 |
| 1 | LOGO | HKA Logo:Logo | G*** |
| 1 | LQW18AN2N2D10D | Inductor_SMD:L_0603_1608Metric | L3 |
| 1 | MX25UM51245GXDI00-TR | MX25UM51245GXDI00-TR:BGA24C100P5X5_600X800X120 | IC5 |
| 1 | PJ-102B | PJ-102B:PJ102B | J8 |
| 1 | SI1062X-T1-GE3 | SI1062X-T1-GE3:SOTFL50P160X80-3N | Q1 |
The 217 most common of 221 parts.
Similar boards
- 6 layers45 × 75 mm

- 6 layers150.1 × 110.1 mm

- 2 layers135.3 × 78.4 mm

Mseq
MF-Room/mseq_pcb
KiCad 10 hardware design for MSeq embedded, the microcontroller implementation of the MSeq MIDI sequencer.
93 parts1CERN-OHL-S-2.0 - 6 layers14.5 × 90 mm

- 4 layers26.5 × 70 mm

PytheasFC 0.1.0
nate-i-think/pytheas
custom flight controller for a thrust vectoring and self-landing rocket @ princeton designed in a day
74 partsApache-2.0 - 2 layers75.2 × 128.3 mm

- 6 layers50 × 60 mm

Healthylink compute v5
Protocentral/protocentral_healthypi6_hardware
Open hardware design files for HealthyPi 6 — STM32H757 vital-signs monitor with the HealthyLink modular expansion bus
124 parts2CERN-OHL-P-2.0 - 4 layers94.3 × 65 mm

Questions
How big is the STM32N6 Thesis Board PCB?
It measures 62.3 × 94.3 mm and has 4 copper layers, 1.58 mm thick.
What parts does the STM32N6 Thesis Board use?
221 parts, built around the ST1S31PUR, ESDALC6V1W5, LD1117S33TR(MS) and LD1117S50TR(MS). The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the STM32N6 Thesis Board KiCad files?
From the tobiasbaas/Roboterarm1 repository on GitHub, at the commit this page was made from: the board is 03_Hardware/STM32N6_Thesis_Board/STM32N6_Thesis_Board.kicad_pcb and its schematic 03_Hardware/STM32N6_Thesis_Board/Camera.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the STM32N6 Thesis Board design in my own project?
Its repository states no licence, so its author keeps all rights: ask tobiasbaas before reusing the design.