2 layers100 × 99.8 mm
Pre Ignition
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.
152 parts19
4 layers71.9 × 91 mm
Klipper
tobetter/3DPrinterShield4"3D Printer Shield" is a board to run 3D printer using ODROID single board computer, technically this board is designed to control the motor driver modules with TMC2209 (UART) or TMC2130 (SPI) through the on-board GPIO…
- Size
- 71.9 × 91 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 111
- Nets
- 130
- Pads
- 438
- Tracks, vias
- 1,316, 151
- Pours
- 16
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 16 Mar 2021
- Updated
- 17 Mar 2021
Overview
Klipper is an open-source printed circuit board by tobetter, from the tobetter/3DPrinterShield repository on GitHub, published under the GPL-3.0 licence. It is a 4-layer board of 71.9 × 91 mm with 111 parts on 130 nets, routed with 1,316 tracks and 151 vias.
It is built around the 100UF/35V, IRFR024N and 10UF 10V, with the IRLR7843TRPBF and S1D among its other parts. Its parts include 41 resistors, 32 connectors, 16 capacitors, 6 diodes and 5 ICs. It belongs with the robots and motor control boards of this library.
Main components
5
100UF/35V
C1812C1812 SMT ROHSJLCPCB AssemblyUncategorised
IRFR024N
TO-252-55℃~+175℃ 1 N-channel 1.9nF 2.5V 25A 30nC@30V 33mΩ@10V 50W 60V 95pF TO-252 MOSFETs ROHSTECH PUBLICMOSFETs
10UF 10V
08050805 Multilayer Ceramic Capacitors MLCC - SMD/SMT ROHSSamsung Electro-MechanicsMultilayer Ceramic Capacitors MLCC - SMD/SMT
IRLR7843TRPBF
TO-252140W 161A 2.3V@250uA 3.3mΩ@10V,15A 30V N-Channel DPAK MOSFETs ROHSInfineon TechnologiesMOSFETs
S1D
SMA(DO-214AC)-65℃~+150℃ 1 Independent 1.1V@1A 1A 200V 5uA@200V SMA(DO-214AC) Diodes - General Purpose ROHSDiodes IncorporatedDiodes - General Purpose
README
README.md3D Printer Shield
"3D Printer Shield" is a board to run 3D printer using ODROID single board computer, technically this board is designed to control the motor driver modules with TMC2209 (UART) or TMC2130 (SPI) through the on-board GPIO headers without an additional processessor.
Originally this project is started to use RAMPS 1.6, but has changed to design a new board since board connection is quite different.
The board has been tested with Ender-3 and runs by Klipper.
Then later, I've built an OS image to run Klipper on ODROID-C4 and the image can be downloaded from the link
Parts
111| Qty | Value | Footprint | References |
|---|---|---|---|
| 15 | 100 | Resistor_SMD:R_0603_1608Metric | R12, R13, R14, R23, R24, R25, R27, R28, R29, R31, R32, R33, R35, R36, R37 |
| 7 | 0.1uF | Capacitor_SMD:C_0603_1608Metric | C1, C2, C3, C5, C8, C9, C11 |
| 7 | 100uF/35V | Capacitor_SMD:CP_Elec_6.3x5.9 | C4, C10, C12, C13, C14, C15, C16 |
| 6 | 4.7K | Resistor_SMD:R_0603_1608Metric | R4, R5, R6, R9, R15, R18 |
| 6 | MountingHole_Pad | MountingHole:MountingHole_3.2mm_M3_DIN965_Pad | H1, H2, H3, H4, H6, H7 |
| 5 | Conn_02x04_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J21, J22, J23, J24, J30 |
| 4 | 10 | Resistor_SMD:R_0603_1608Metric | R7, R10, R16, R19 |
| 4 | 100k | Resistor_SMD:R_0603_1608Metric | R8, R11, R17, R20 |
| 4 | 10K | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R38 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric | R22, R26, R30, R34 |
| 4 | 1k | Resistor_SMD:R_0603_1608Metric | R21, R39, R40, R41 |
| 4 | Conn_01x02 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J13, J14, J15, J16 |
| 4 | Conn_01x04 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J17, J18, J19, J20 |
| 4 | LED | LED_SMD:LED_0603_1608Metric | D3, D4, D5, D6 |
| 3 | IRFR024N | Package_TO_SOT_SMD:TO-252-3_TabPin2 | Q1, Q2, Q4 |
| 2 | 10uF/10 | Capacitor_SMD:C_1206_3216Metric | C6, C7 |
| 2 | Conn_01x07 | Connector_PinSocket_2.54mm:PinSocket_1x07_P2.54mm_Vertical | J12, J31 |
| 1 | Conn_02x12_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x12_P2.54mm_Vertical | J29 |
| 1 | Conn_02x20_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_Vertical | J9 |
| 1 | DCIN | TerminalBlock:TerminalBlock_BR_762C_P7.62mm | J1 |
| 1 | E0 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J7 |
| 1 | E0 | Package_DIP:MOTOR_CARRIER | U4 |
| 1 | E0 | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J28 |
| 1 | FAN0 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J8 |
| 1 | FAN1 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J11 |
| 1 | FAN_POWER | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J32 |
| 1 | Fuse | Fuse:FRU500-30F | F1 |
| 1 | HB | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J10 |
| 1 | IRLR7843TRPBF | Package_TO_SOT_SMD:TO-252-3_TabPin2 | Q3 |
| 1 | MCP23017_SO | Package_SO:SOIC-28W_7.5x17.9mm_P1.27mm | U5 |
| 1 | S1D | Diode_SMD:D_SMC_Handsoldering | D1 |
| 1 | SS54CF | Diode_SMD:D_SMC_Handsoldering | D2 |
| 1 | TH0 | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J5 |
| 1 | THB | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J6 |
| 1 | X | Package_DIP:MOTOR_CARRIER | U1 |
| 1 | X | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J25 |
| 1 | X-STOP | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J2 |
| 1 | Y | Package_DIP:MOTOR_CARRIER | U2 |
| 1 | Y | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J26 |
| 1 | Y-STOP | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J3 |
| 1 | Z | Connector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_Vertical | J27 |
| 1 | Z | Package_DIP:MOTOR_CARRIER | U3 |
| 1 | Z-STOP | Connector_JST:JST_XH_B2B-XH-A_1x02_P2.50mm_Vertical | J4 |
Questions
How big is the Klipper PCB?
It measures 71.9 × 91 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Klipper use?
111 parts, built around the 100UF/35V, IRFR024N, 10UF 10V and IRLR7843TRPBF. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Klipper KiCad files?
From the tobetter/3DPrinterShield repository on GitHub, at the commit this page was made from: the board is Klipper.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Klipper design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
Similar boards
- 2 layers
- 2 layers136 × 88 mm
- 4 layers79.9 × 80 mm
- 2 layers184 × 94 mm
FIC Board
DanielRHoefer/satoshi-emblem
Toyota backlit grill emblem with sequential LEDs for 3rd gen 4runner
193 parts1 - 2 layers43.6 × 39.5 mm
- 2 layers100 × 55 mm
Invpcb
Prajwal-sahyadri-ECE/-Optimized-Powersupply-design-
A highly detailed PCB to maintain an power supply for a defined hardware architecture specifically for ICS system
66 partsMIT - 2 layers100 × 100 mm
