
Closed deck x4
OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

Hardware is based off an open source project called Speeduino by Josh Stewart.
Pre Ignition is an open-source printed circuit board by OpenLogicEFI, from the OpenLogicEFI/Hardware repository on GitHub. It is a 2-layer board of 100 × 99.8 mm with 152 parts on 178 nets, routed with 786 tracks and 348 vias.
It is built around the TC4424EPA, DRV8825PWP and SRV05-4-P-T7, with the L78M05ABDT-TR, ULN2003A and 1N4148WS among its other parts. Its parts include 61 resistors, 30 capacitors, 22 diodes, 11 transistors and 8 connectors. It belongs with the AVR (ATmega, ATtiny) boards of this library.
Formerly: DetonationEMS
OpenLogicEFI ECU's are based off an open source project called Speeduino by Josh Stewart. Currently all released boards use official Speeduino firmware. In TunerStudio set to "Board Layout" to "Speeduino 0.4"
All designs are released under the TAPR Open Hardware License v1.0
The Official Speeduino Manual, documents and discord are the best places to start.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 16 | 1k | Resistor_SMD:R_0603_1608Metric | R1, R2, R3, R4, R5, R6, R20, R21, R25, R29, R31, R35, R38, R41, R46, R61 |
| 12 | 100k | Resistor_SMD:R_0603_1608Metric | R11, R12, R13, R14, R15, R16, R17, R18, R32, R36, R39, R42 |
| 11 | 100nF | Capacitor_SMD:C_0603_1608Metric | C3, C5, C9, C12, C16, C18, C21, C23, C25, C27, C29 |
| 9 | 220nF | Capacitor_SMD:C_0603_1608Metric | C7, C15, C17, C19, C20, C22, C24, C26, C28 |
| 9 | 470 | Resistor_SMD:R_0603_1608Metric | R50, R51, R54, R55, R56, R57, R58, R59, R60 |
| 8 | 1N4148WS | Diode_SMD:D_SOD-323F | D4, D5, D6, D7, D8, D9, D10, D11 |
| 7 | AO3400A | Package_TO_SOT_SMD:SOT-23 | Q5, Q6, Q7, Q8, Q9, Q10, Q11 |
| 6 | 2.4k | Resistor_SMD:R_0603_1608Metric | R22, R23, R24, R26, R27, R28 |
| 6 | LED-Green | LED_SMD:LED_0603_1608Metric | D16, D17, IGN1, IGN2, IGN3, IGN4 |
| 5 | 470r | Resistor_SMD:R_0402_1005Metric | R7, R8, R9, R10, R62 |
| 4 | 10 | Resistor_SMD:R_1206_3216Metric | R30, R34, R37, R40 |
| 4 | IRFR024 | Package_TO_SOT_SMD:TO-252-2 | Q1, Q2, Q3, Q4 |
| 4 | SMF30CA | Diode_SMD:D_SOD-123F | D12, D13, D14, D15 |
| 2 | 10k | Resistor_SMD:R_0603_1608Metric | R47, R52 |
| 2 | 10nF | Capacitor_SMD:C_0603_1608Metric | C6, C8 |
| 2 | 10uF | Capacitor_Tantalum_SMD:CP_EIA-3216-18_Kemet-A | C4, C31 |
| 2 | 1uF | Capacitor_SMD:C_0603_1608Metric | C10, C11 |
| 2 | 2.49k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal | R43, R44 |
| 2 | 2k | Resistor_SMD:R_0603_1608Metric | R19, R33 |
| 2 | 47pF | Capacitor_SMD:C_0603_1608Metric | C13, C14 |
| 2 | 51k | Resistor_SMD:R_0603_1608Metric | R45, R48 |
| 2 | Conn_01x03 | Detonation:1x03-Proto | JP4, JP5 |
| 2 | MOS Bypass | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2 |
| 2 | SRV05-4-P-T7 | Package_TO_SOT_SMD:SOT-23-6 | U3, U4 |
| 2 | TC4424 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U1, U2 |
| 1 | 2.2uF | Capacitor_SMD:C_1206_3216Metric | C1 |
| 1 | 3.9k | Resistor_SMD:R_0603_1608Metric | R53 |
| 1 | 330nF | Capacitor_SMD:C_0805_2012Metric | C2 |
| 1 | 7D220KTR | Detonation:MOV07D220KTR | RV1 |
| 1 | Arduino_Mega2560_Shield-Arduino | Detonation:Arduino-Mega2560-Shield-Speeduino | XA1 |
| 1 | BAV99 | Package_TO_SOT_SMD:SOT-23 | D18 |
| 1 | Conn_02x10_Counter_Clockwise | Detonation:Molex_Micro-Fit_3.0_43045-2000_2x10_P3.00mm_Horizontal | J4 |
| 1 | Conn_02x12_Counter_Clockwise | Detonation:PROTO-3X8-24pin | J3 |
| 1 | Conn_02x12_Counter_Clockwise | Detonation:Molex_Micro-Fit_3.0_43045-2400_2x12_P3.00mm_Horizontal | J6 |
| 1 | DCWERX | Detonation-Logos:DCWerx-19mm | G1 |
| 1 | DESIGN | Detonation-Logos:Design by 20mm | G5 |
| 1 | DRV8825 | Detonation:DVR8825-Labeled-Front | A1 |
| 1 | L78M05ABDT-TR | Detonation:TO-252-2-Thermal | IC1 |
| 1 | LOGO | Detonation-Logos:SpeeduinoCompatible-17mm | G3 |
| 1 | M7 | Diode_SMD:D_SMA | D1 |
| 1 | MAP bypass | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP3 |
| 1 | Map/Baro Sensor Socket | Connector_PinSocket_2.54mm:PinSocket_2x03_P2.54mm_Vertical | J7 |
| 1 | OSHW-Logo2_7.3x6mm_SilkScreen | Symbol:OSHW-Logo2_7.3x6mm_SilkScreen | G2 |
| 1 | Pre-Ignition | Detonation-Logos:Pre-IgnitionX4-35mm | G4 |
| 1 | Reset Control | Detonation:1x02-Proto | J8 |
| 1 | Serial0 | Detonation:1X4-PROTO | J1 |
| 1 | Serial3 | Detonation:1X4-PROTO | J2 |
| 1 | SolderJumper_3_Bridged12 | Detonation:SolderJumper-3_P1.3mm_Bridged12_RoundedPad1.0x1.5mm_NumberLabels | JP6 |
| 1 | TVS 26a | Diode_SMD:D_SMA | D2 |
| 1 | TVS 5.0A | Diode_SMD:D_SMA | D3 |
| 1 | ULN2003A | Package_SO:SOIC-16_3.9x9.9mm_P1.27mm | U5 |
| 1 | VR_Header | Detonation:Socket_VRConditioner_Corrected | J5 |

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

OpenLogicEFI/Hardware
Hardware is based off an open source project called Speeduino by Josh Stewart.

tobetter/3DPrinterShield
"3D Printer Shield" is a board to run 3D printer using ODROID single board computer, technically this board is designed to control the motor driver modules with TMC2209 (UART) or TMC2130 (SPI) through the on-board GPIO…


v-cu/dpf-load-monitor-wide
ESP32-P4 diagnostic display for VAG diesels — live DPF and engine data over CAN (UDS) on a 3.19" ultra-wide AMOLED. Firmware, KiCad files, BOM and 3D enclosure.

Robast-GmbH/PCB_Designs
This repository contains all the necessary files and instructions for the PCBs that are designed using KiCad. Here is an overview of the main components: - .github: Contains Github-specific configurations, including…


ilomon10/embedded-totalizer-hour-meter
ESP32 engine hour meter & totalizer: firmware, SensorFrame protocol, Node host tools, KiCad PCB and a Deno device simulator

Churrosoft/OpenEFI-PCB
Coleccion de PCB y planos recomendados para montar una OpenEFI

Churrosoft/uEFI-v6.x
Speeduino compatible board, x4 ignition channels, x4 injection channels, 2&4 wire IAC
It measures 100 × 99.8 mm and has 2 copper layers, 1.6 mm thick.
152 parts, built around the TC4424EPA, DRV8825PWP, SRV05-4-P-T7 and L78M05ABDT-TR. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the OpenLogicEFI/Hardware repository on GitHub, at the commit this page was made from: the board is Engine Managment/Pre-Ignition/Pre-Ignition x4/MX4C/Pre_Ignition.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask OpenLogicEFI before reusing the design.