
Sensor node
thewriterben/OpenCircuitCore
Electronics engine: circuits as atopile code, verified and emitted through KiCad

Electronics engine: circuits as atopile code, verified and emitted through KiCad
Sensor breakout is an open-source printed circuit board by thewriterben, from the thewriterben/OpenCircuitCore repository on GitHub, published under the Apache-2.0 licence. It is a 2-layer board of 22 × 26 mm with 6 parts on 4 nets.
It is built around the BME280. Its parts include 2 resistors, 1 capacitor and 1 IC. It belongs with the interfaces and adapters and sensors and measurement boards of this library.
A BME280 I2C breakout, and the first board here whose connectivity comes from its schematic rather than being asserted alongside it.
reference-esp32s3 proved the toolchain, but its schematic and board were generated independently — nothing tied them together, so nothing stopped them disagreeing. This board is generated from make_reference_schematic.PARTS (the same single source of truth as the schematic) and its pads are bound to nets read out of the schematic's exported netlist.
# 1. schematic
python scripts/make_reference_schematic.py
kicad-cli sch erc --exit-code-violations --severity-error -o erc-report.txt sensor-subcircuit.kicad_sch
kicad-cli sch export netlist -o sensor-subcircuit.net sensor-subcircuit.kicad_sch
# 2. board, from that netlist
<KiCad>/bin/python.exe scripts/make_sensor_breakout.py
kicad-cli pcb drc --severity-error -o drc-report.txt sensor-breakout.kicad_pcboutline 22.0 x 26.0 mm, 4 component(s), 2 mounting hole(s)
nets from schematic: +3V3, GND, SCL, SDA
Found 0 violations
Found 10 unconnected items0 violations, 10 unconnected is the correct and intended result. The board has real nets and an unrouted ratsnest — the state a router or a human takes over from. Verified from the saved file:
U2 [('1','GND'), ('2','+3V3'), ('3','SDA'), ('4','SCL'),
('5','GND'), ('6','+3V3'), ('7','GND'), ('8','+3V3')]
R1 [('1','+3V3'), ('2','SDA')]That matches the schematic: CSB high for I2C, SDO low for address 0x76, R1 pulling SDA up to +3V3.
PLACEMENT, not optimised.| Qty | Value | Footprint | References |
|---|---|---|---|
| 2 | 4.7k | R_0603_1608Metric | R1, R2 |
| 2 | MountingHole_2.2mm_M2 | MountingHole_2.2mm_M2 | H1, H2 |
| 1 | 100n | C_0603_1608Metric | C1 |
| 1 | BME280 | Bosch_LGA-8_2.5x2.5mm_P0.65mm_ClockwisePinNumbering | U2 |

thewriterben/OpenCircuitCore
Electronics engine: circuits as atopile code, verified and emitted through KiCad

nkitanov/iaq_board
IAQ Board is a DIY (Do-It-Yourself) device for measuring internal air quality


New-England-Weather-Balloon-Society/Tiny4FSK
Horus Binary v2 HAB Tracker


kbx81/ClimateSprinklerController
ESP32-based climate and sprinkler controller for use with ESPHome

crnicholson/StratoSoar-MK3
StratoSoar MK3, an autonomous glider meant for high-altitudes, accessible to everyone


CCHS-Melbourne/ESPlant
Environmental Sensor Plant - solar WiFi gardening/meteorological sensor using ESP8266
It measures 22 × 26 mm and has 2 copper layers, 1.6 mm thick.
6 parts, built around the BME280. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the thewriterben/OpenCircuitCore repository on GitHub, at the commit this page was made from: the board is boards/sensor-breakout/sensor-breakout.kicad_pcb and its schematic boards/reference-esp32s3/sensor-subcircuit.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the Apache-2.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).