Skip to the content
2 layers12 × 14 mmNanoAlt Alpha, the printed circuit board in 3D

Repo for the nanoAlt open-source nano-scale rocketry altimeter family

Size
12 × 14 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
15
Pads
43
Tracks, vias
102, 21
Pours
2
Routed
Yes
KiCad
KiCad 5 (file 20171130)
Created
23 Oct 2019
Updated
29 May 2020

Overview

NanoAlt Alpha is an open-source printed circuit board by the-flame-trench, from the the-flame-trench/nanoAlt repository on GitHub. It is a 2-layer board of 12 × 14 mm with 12 parts on 15 nets, routed with 102 tracks and 21 vias.

It is built around the ATTINY24A-CCU and MS563702BA03-50. Its parts include 4 resistors, 2 capacitors, 2 ICs, 1 diode and 1 connector. It belongs with the AVR (ATmega, ATtiny) boards of this library.

Main components

2

README

README.md

nanoAlt

This repo contains the open source hardware and software for The Flame Trench's nanoAlt nano-scale rocketry altimeter family.

The project is not currently being prioritised, but we hope to be able to make nanoAlt Alpha available in kit form soon.

nanoAlt Alpha

nanoAlt Alpha is the base version of the altimeter, using an ATTiny24A and simple barometer. It is powered via 4.8mm coin cell, and reports altitude readings via flashing LED. The software for nanoAlt Alpha is in an early state of development owing to the delays in finalising assembly for the boards, and is therefore unpublished at this time. The nanoAlt Alpha boards expose a set of programming pins to allow custom programming of the microcontroller.

nanoAlt Integrate

nanoAlt Integrate is a series of fittings designed to mount the nanoAlt family in a variety of common rocketry tube diameters. Currently a BT-5 test piece is published, owing to the nanoAlt Alpha initially being designed for very small minimum diameter builds.

Parts

12
QtyValueFootprintReferences
310KResistor_SMD:R_0402_1005MetricR1, R2, R3
2100nCapacitor_SMD:C_0402_1005MetricC1, C2
12mm_holeMy_VIAS:2mm_holeINTEGRATE
133Resistor_SMD:R_0402_1005MetricR4
1ATtiny24A-CCUPackage_BGA:UFBGA-15_3.0x3.0mm_Layout4x4_P0.65mmU1
1AVR_SPI_PROG_3X2TESTPOINTSMy_Connectors:50mil_POGOJ1
1Keystone2994_4.8mm_coincellholderMy_CONNECTORS:Keystone2994_4.8mm_coincellholderBATT_3V
1LEDLED_SMD:LED_0402_1005MetricD1
1MS563702BA03-50MS5637_1IC1

Similar boards

  • 4 layers50 × 50 mmPlant monitor, the printed circuit board in 3D

    Plant monitor

    PimentoFr/plant-monitor

    Developpement d'un capteur de potager indoor/outdoorn solaire et connecté via Sigfox

    208 parts
  • 2 layers101.1 × 70 mmLuftmeter, the printed circuit board in 3D

    Luftmeter

    stustanet/Luftmeter

    Modular (=hacky) Air Quality Monitoring Platform.

    85 parts
  • 4 layers100 × 70 mmZP Breakout, the printed circuit board in 3D

    ZP Breakout

    UWARG/efs-zeropilot-breakout

    Breakout Board for Zeropilot rev 1.0.

    193 parts
  • 2 layers86.4 × 40.6 mmPhoenix, the printed circuit board in 3D

    Phoenix

    yorkaerospace/Phoenix-hw

    RP2040 based flight computer

    102 partsCC-BY-SA-4.0
  • 2 layers54 × 54 mmPCB C, the printed circuit board in 3D

    PCB C

    dragondgold/AtSat

    Plataforma educativa basada en un satélite CanSat

    64 parts5GPL-3.0
  • 2 layers54 × 54 mmPCB C, the printed circuit board in 3D

    PCB C

    dragondgold/CanSat

    Plataforma educativa basada en un satélite CanSat

    58 parts1GPL-3.0
  • 2 layersNrf bga, the printed circuit board in 3D

    Nrf bga

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    12 parts14kMIT

Questions

How big is the NanoAlt Alpha PCB?

It measures 12 × 14 mm and has 2 copper layers, 1.6 mm thick.

What parts does the NanoAlt Alpha use?

12 parts, built around the ATTINY24A-CCU and MS563702BA03-50. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the NanoAlt Alpha KiCad files?

From the the-flame-trench/nanoAlt repository on GitHub, at the commit this page was made from: the board is nanoAlt_Alpha/nanoAlt_Alpha.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the NanoAlt Alpha design in my own project?

Its repository states no licence, so its author keeps all rights: ask the-flame-trench before reusing the design.