

ZP Breakout
Breakout Board for Zeropilot rev 1.0.
- Size
- 100 × 70 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 193
- Nets
- 243
- Pads
- 782
- Tracks, vias
- 2,071, 318
- Pours
- 15
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 17 Jan 2021
- Updated
- 4 Feb 2021
Overview
ZP Breakout is an open-source printed circuit board by UWARG, from the UWARG/efs-zeropilot-breakout repository on GitHub. It is a 4-layer board of 100 × 70 mm with 193 parts on 243 nets, routed with 2,071 tracks and 318 vias.
It is built around the STM32F091RCT7, STM32F765ZGT6 and MS563702BA03-50, with the FT4232HL, ICM-20602 and M24C64-WDW6TP among its other parts. Its parts include 64 capacitors, 46 resistors, 16 diodes, 7 ICs and 5 connectors. It belongs with the interfaces and adapters boards and the STM32 boards of this library.
Main components
9STM32F091RCT7
LQFP-64(10x10)-40℃~+105℃ 12bit 12bit 256KB 2V~3.6V 32 Bit 32KB 48MHz 52 ARM Cortex-M0 Built-in FLASH LQFP-64(10x10) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)STM32F765ZGT6
LQFP-144(20x20)-40℃~+85℃ 1.7V~3.6V 114 12bit 12bit 1MB 216MHz 32 Bit 512KB ARM Cortex-M7 Built-in FLASH LQFP-144(20x20) Microcontrollers (MCU/MPU/SOC) ROHSSTMicroelectronicsMicrocontrollers (MCU/MPU/SOC)MS563702BA03-50
SMD-4P,3x3mm-40℃~+85℃ 1.5V~3.6V 100nA 10pa 16.44ms 200pa 30Kpa~1.2bar I2C SMD-4P,3x3mm Pressure Sensors ROHSTE ConnectivityPressure SensorsFT4232HL
QFP64Quad High Speed USB to Multipurpose UART/MPSSE ICFTDIUncategorisedICM-20602
LGA-16(3x3)-40℃~+85℃ 1.71V~3.45V 16bit 1KB 6uA IMU (accelerometer + gyroscope) SPI、I2C X,Y,Z X,Y,Z ±16g ±2000dps 运动事件检测 LGA-16(3x3) Accelerometers ROHSTDK InvenSenseAccelerometersM24C64-WDW6TP
TSSOP-8-40℃~+85℃ 1MHz 2.5V~5.5V 2.5mA 200 Years 3uA 4,000,000 Cycles 450ns、900ns 5ms 64Kbit Hardware write protection function、Built-in power-on reset (POR)、Page write protection function、Built-in error correction code (ECC) function I2C TSSOP-8 EEPROM ROHSSTMicroelectronicsEEPROMMCP1826S-3302E/DB
SOT-223-3-40℃~+125℃ 1 1A 220uA 3.3V 400mV@(1A) 60dB@(100Hz) 6V Fixed Positive Under Voltage Lockout、Over Current Protection、Over Temperature Protection、Short Circuit Protection SOT-223-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSMicrochip TechnologyVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsBSS84LT1G
SOT-23-55℃~+150℃ 1 P-Channel 10Ω@5V 130mA 17pF 2.2nC@10V 225mW 2V 36pF 50V 6.5pF P-Channel SOT-23 MOSFETs ROHSonsemiMOSFETsBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETs
README
README.mdZP-breakout
Breakout Board for Zeropilot rev 1.0.
Parts
193| Qty | Value | Footprint | References |
|---|---|---|---|
| 33 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad0.84x1.00mm_HandSolder | C24, C25, C26, C27, C28, C29, C30, C31, C33, C34, C35, C36, C44, C46, C47, C48 +17 |
| 15 | 10K | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R1, R2, R19, R22, R24, R26, R27, R35, R44, R45, R46, R47, R48, R49, R54 |
| 14 | GH-6 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | PWM1-2, PWM3-4, PWM5-6, PWM7-8, PWM9-10, PWM11-12, SPI1_IMU1, SPI2, SPI4, SPI5, SPI6_SAFE_AUTO1, UART1, UART2, UART4 |
| 13 | 100 | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R3, R4, R5, R6, R7, R8, R9, R16, R17, R18, R51, R52, R53 |
| 10 | GH-4 | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | GPIO_AUTO1, GPIO_SAFE1, I2C2_ALT1, I2C4, J1, SWD_AUTO1, SWD_SAFE1, TMS1-2, UHF1, USS1 |
| 8 | 4.7uF | Capacitor_SMD:C_0603_1608Metric_Pad0.84x1.00mm_HandSolder | C3, C4, C38, C59, C60, C63, C72, C76 |
| 8 | LED | LED_SMD:LED_0603_1608Metric_Pad0.67x1.00mm_HandSolder | D2, D3, D5, D6, D7, D12, D13, D14 |
| 7 | TEST | TestPoint:TestPoint_Pad_D1.5mm | TP1, TP2, TP3, TP4, TP5, TP6, TP35 |
| 6 | 0 | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R20, R21, R23, R25, R41, R42 |
| 5 | 1uF | Capacitor_SMD:C_0603_1608Metric_Pad0.84x1.00mm_HandSolder | C5, C6, C32, C37, C70 |
| 4 | 10nF | Capacitor_SMD:C_0603_1608Metric_Pad0.84x1.00mm_HandSolder | C1, C2, C43, C69 |
| 4 | 14pF | Capacitor_SMD:C_0603_1608Metric_Pad0.84x1.00mm_HandSolder | C22, C23, C65, C66 |
| 4 | 7pF | Capacitor_SMD:C_0603_1608Metric_Pad0.84x1.00mm_HandSolder | C39, C40, C67, C68 |
| 4 | GH-2 | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | I2C1_SAFE_AUTO1, UART_DBG_AUTO1, UART_DBG_SAFE1, V_ISNS1 |
| 4 | MountingHole_M3 | MountingHole:MountingHole_3.2mm_M3_ISO14580_Pad | H1, H2, H3, H4 |
| 3 | 2.2uF | Capacitor_SMD:C_0603_1608Metric_Pad0.84x1.00mm_HandSolder | C41, C42, C45 |
| 3 | GH-3 | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | AIRSPEED1, PPM1, RSSI1 |
| 3 | PWR_LED | LED_SMD:LED_0603_1608Metric_Pad0.67x1.00mm_HandSolder | D4, D15, D16 |
| 3 | TVS | Diode_SMD:D_0603_1608Metric_Pad0.67x1.00mm_HandSolder | D1, D10, D11 |
| 2 | 10 | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R37, R38 |
| 2 | 220 | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R40, R43 |
| 2 | 22K | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R32, R33 |
| 2 | 32.768kHz | Crystal:Crystal_SMD_MicroCrystal_CC7V-T1A-2Pin_3.2x1.5mm | Y1, Y4 |
| 2 | 600R | Inductors_SMD:L_0603_HandSoldering | L3, L4 |
| 2 | 8MHz | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm_HandSoldering | Y2, Y5 |
| 2 | 8pF | Capacitor_SMD:C_0603_1608Metric_Pad0.84x1.00mm_HandSolder | C61, C62 |
| 2 | BSS84LT1G | TO_SOT_Packages_SMD:SOT-23 | Q1, Q3 |
| 2 | D | Diode_SMD:D_PowerDI-123 | D8, D9 |
| 2 | SW_Push_Dual_1-2short_3-4short | WARG:Button | SW1, SW2 |
| 1 | 100K | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R50 |
| 1 | 11K | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R30 |
| 1 | 12K | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R36 |
| 1 | 150K | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R29 |
| 1 | 1K | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R39 |
| 1 | 3.3uF | Capacitor_SMD:C_0603_1608Metric_Pad0.84x1.00mm_HandSolder | C56 |
| 1 | 4.7K | Resistor_SMD:R_0603_1608Metric_Pad0.84x1.00mm_HandSolder | R34 |
| 1 | BLM18PG221SN1D | Inductors_SMD:L_0603_HandSoldering | L1 |
| 1 | BSS138 | Package_TO_SOT_SMD:TSOT-23 | Q2 |
| 1 | CONN-8 | Connector_PinHeader_2.54mm:PinHeader_1x08_P2.54mm_Vertical | J32 |
| 1 | Conn_01x02 | Connector_PinSocket_2.54mm:PinSocket_2x01_P2.54mm_Vertical | J31 |
| 1 | Conn_02x02_Odd_Even | Connector_PinSocket_2.54mm:PinSocket_2x02_P2.54mm_Vertical | J30 |
| 1 | Crystal_GND24 | Crystal:Crystal_SMD_2520-4Pin_2.5x2.0mm | Y3 |
| 1 | FT4232H | Package_QFP:LQFP-64_10x10mm_P0.5mm | U8 |
| 1 | ICM-20602 | WARG-kicad:ICM-20602 | U6 |
| 1 | M24C64-WDW6TP | Package_SO:TSSOP-8_4.4x3mm_P0.65mm | U5 |
| 1 | MCP1826S-3302E/DB | Package_TO_SOT_SMD:SOT-223 | U1 |
| 1 | MS5637-02BA03 | WARG-kicad:MS5637-02BA03 | U7 |
| 1 | Micro_SD_Card | WARG:micro_sd | J8 |
| 1 | STM32F091RCT7 | Package_QFP:LQFP-64_10x10mm_P0.5mm | U9 |
| 1 | STM32F765ZGT6 | Package_QFP:LQFP-144_20x20mm_P0.5mm | U4 |
| 1 | USB_MICRO_B | WARG:USB_Micro-B_10118194-0001LF | J9 |
Similar boards
- 2 layers130.6 × 112 mm

- 4 layers50 × 50 mm

Plant monitor
PimentoFr/plant-monitor
Developpement d'un capteur de potager indoor/outdoorn solaire et connecté via Sigfox
208 parts - 4 layers68.6 × 53.3 mm

- 2 layers165 × 100 mm

- 2 layers60 × 70 mm

20210213 Projects PassiveBalanceBoard
simple-ee/mBMS
This is the modular BMS for use with 8S LiFePO4
97 parts8MIT - 4 layers43.2 × 62 mm

USBAudioBridge
fsodari/USBAudioBridge
NXP RT1010 based USB to I2S bridge to connect to a Digilent Arty A7.
120 parts - 4 layers100 × 120 mm

Micromouse pcb
MukeshSethy/micromouse-runner
This is my repo for the first version of full size micromouse development.
184 parts - 4 layers65.6 × 57.2 mm

Macro devboard ESP32
YingK8/ESP32-BLE-Macro-Pad
A compact, programmable macropad with Bluetooth connectivity, featuring 6 mechanical keys and a rotary encoder for media control.
55 parts
Questions
How big is the ZP Breakout PCB?
It measures 100 × 70 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ZP Breakout use?
193 parts, built around the STM32F091RCT7, STM32F765ZGT6, MS563702BA03-50 and FT4232HL. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ZP Breakout KiCad files?
From the UWARG/efs-zeropilot-breakout repository on GitHub, at the commit this page was made from: the board is Hardware/ZP-Breakout.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ZP Breakout design in my own project?
Its repository states no licence, so its author keeps all rights: ask UWARG before reusing the design.