thainnos/ICSscannerDiode11Architecture for a secure ICS network scanner with an intelligent data diode
NetworkScanner is an open-source printed circuit board by thainnos, from the thainnos/ICSscannerDiode repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 160 × 100 mm with 120 parts on 163 nets, routed with 802 tracks and 210 vias.
It is built around the LMZ23605TZ, BSS84 and ZPD15. Its parts include 54 resistors, 21 connectors, 12 capacitors, 11 diodes and 3 ICs. It belongs with the STM32 boards of this library.
| Qty | Value | Footprint | References |
|---|---|---|---|
| 36 | 10kR | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R10, R15, R16, R17, R18, R21, R24, R25, R28, R29, R30, R31, R32, R33, R34, R35 +20 |
| 10 | 100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C3, C4, C5, C6, C7, C8, C9, C10, C11, C12 |
| 8 | 330R | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R11, R12, R19, R20, R22, R23, R26, R27 |
| 8 | LED | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4, D5, D6, D7, D8, D9, D10, D11 |
| 5 | 0R | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R3, R5, R49, R50 |
| 4 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J9, J11, J20, J21 |
| 4 | Conn_01x03_Male | Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_Vertical | J8, J13, J17, J18 |
| 4 | Conn_02x05_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x05_P2.54mm_Vertical | J7, J10, J12, J14 |
| 3 | 100kR | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R2, R4, R6 |
| 3 | BSS84 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2, Q3 |
| 2 | 22µF | Capacitor_SMD:C_1206_3216Metric_Pad1.42x1.75mm_HandSolder | C1, C2 |
| 2 | Conn_01x04_Female | Connector_PinSocket_2.54mm:PinSocket_1x04_P2.54mm_Vertical | J3, J4 |
| 2 | Conn_01x06_Male | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J15, J16 |
| 2 | Jack-DC | Connector_BarrelJack:BarrelJack_CUI_PJ-063AH_Horizontal | J5, J6 |
| 2 | Raspberry_Pi_2_3 | Connector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_Vertical | J1, J2 |
| 2 | STM32F030CCTx | Package_QFP:LQFP-48_7x7mm_P0.5mm | U1, U2 |
| 2 | ZPD15 | Diode_SMD:D_MiniMELF_Handsoldering | D2, D3 |
| 1 | 1.07kR | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R14 |
| 1 | 5.62kR | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R13 |
| 1 | Conn_02x02_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x02_P2.54mm_Vertical | J19 |
| 1 | LMZ23605 | Package_TO_SOT_SMD:TO-263-7_TabPin4 | U3 |
| 1 | ZPDxx | Diode_SMD:D_MiniMELF_Handsoldering | D1 |
The 104 most common of 120 parts.
It measures 160 × 100 mm and has 2 copper layers, 1.6 mm thick.
120 parts, built around the LMZ23605TZ, BSS84 and ZPD15. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the thainnos/ICSscannerDiode repository on GitHub, at the commit this page was made from: the board is hardware/networkScanner.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).
lewipewi/lelamp-board
A 4-layer replacement power board for LeLamp, Human Computer Lab's open-source expressive robot lamp. One 12 V input, protection, and two independent 5 V rails — plus a level shifter that fixes an LED data link…
Sternenlabor/Vintage-LED-Clock
const char cstrSSID[] = "MyNetwork"; const char cstrPWD[] = "secret";
Ardumower/ardumower
Develop an open source robotic lawn mower (HW+SW reference platform)
UtilitechAS/amsreader-firmware
ESP8266 and ESP32 compatible firmware to read, interpret and publish data to MQTT from smart electrical meters, both DLMS and DSMR is supported
