

ESP32S3
KiCAD data
- Size
- 27.9 × 57.2 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 50
- Nets
- 76
- Pads
- 271
- Tracks, vias
- 408, 113
- Pours
- 6
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 29 Apr 2025
- Updated
- 5 Nov 2026
Overview
ESP32S3 is an open-source printed circuit board by Tert2, from the Tert2/KiCAD repository on GitHub. It is a 4-layer board of 27.9 × 57.2 mm with 50 parts on 76 nets, routed with 408 tracks and 113 vias.
It is built around the ESP32-S3-WROOM-1-N8, CH340K and ADUM3160BRW, with the RT9080N-08GJ5, TC7W74FU,LF and TS5A23159DGSR among its other parts. Its parts include 17 resistors, 12 capacitors, 6 ICs, 4 diodes and 4 connectors. It belongs with the ESP32 boards of this library.
Main components
8ESP32-S3-WROOM-1-N8
SMD,25.5x18mm-40℃~+85℃ -98.2dBm 2.4GHz 20.5dBm 355mA 3V~3.6V 95mA Bluetooth5.0 ESP32-S3 Chip On-board PCB Antenna UART、SPI、I2C、I2S、USB SMD,25.5x18mm WiFi Modules ROHSEspressif SystemsWiFi ModulesCH340K
ESSOP-10-150mil-1mm-20℃~+70℃ 2Mbps 3.3V、5V USB 2.0 USB to serial ESSOP-10-150mil-1mm USB Converters ROHSWCH (Nanjing Qinheng Microelectronics)USB ConvertersADUM3160BRW
SOIC16WFull/Low Speed 2.5 kV USB Digital IsolatorAnalog DevicesUncategorisedRT9080N-08GJ5
TSOT-23-5-40℃~+85℃@(Ta) 1 1.33V@(600mA) 26uVrms 2uA 5.5V 600mA 75dB@(1kHz) 800mV~3.3V、800mV Adjustable、Fixed Over Current Protection、Over Temperature Protection、Enable Positive TSOT-23-5 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSRichtek TechVoltage Regulators - Linear, Low Drop Out (LDO) RegulatorsTC7W74FU,LF
SSOP-8-3mm-40℃~+85℃ 0ns 15ns 26ns@6V,50pF 2V~6V 2uA 5.2mA 5.2mA 5pF 67MHz D-Type Rising Edge Set and Reset TC7W Series SSOP-8-3mm Flip Flops ROHSToshibaFlip FlopsTS5A23159DGSR
VSSOP-10-0.5mm-40℃~+85℃ 1.1Ω 1.65V~5.5V 100MHz 15ns 2 20ns 2:1 VSSOP-10-0.5mm Analog Switches, Multiplexers ROHSTexas InstrumentsAnalog Switches, MultiplexersBSS138
SOT-23-55℃~+150℃ 1 N-channel 1.1Ω@10V、1.2Ω@4.5V 1.2V 1.7nC@10V 17.5pF 340mA 350mW 50V 6.5pF N-Channel SOT-23 MOSFETs ROHShongjiachengMOSFETsWS2812B-5050RGB
SMD-4_5.0X5.0X4.2PSMD-4_5.0X5.0X4.2P SMT ROHSJLCPCB AssemblyUncategorised
README
README.mdOverview
- This is the KiCAD Projects Repository.
- I recommend not to use these KiCAD data.
- Some projects are unfinished or have issues in the circuit.
- I designed these circuits based on whether I can solder them, not on whether the average person can.
Parts
50| Qty | Value | Footprint | References |
|---|---|---|---|
| 6 | 1u | Capacitor_SMD:C_0603_1608Metric | C1, C3, C4, C6, C7, C8 |
| 5 | 10k | Resistor_SMD:R_0603_1608Metric | R7, R8, R9, R10, R16 |
| 4 | 0.1u | Capacitor_SMD:C_0603_1608Metric | C9, C10, C11, C12 |
| 4 | 10k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R13, R14, R15, R17 |
| 4 | 24 | Resistor_SMD:R_0603_1608Metric | R3, R4, R11, R12 |
| 3 | LED_Small | LED_SMD:LED_0603_1608Metric_Pad1.05x0.95mm_HandSolder | D1, D2, D3 |
| 3 | SW_MEC_5E | Yamaha:SW_SKRPABE010 | SW1, SW2, SW3 |
| 2 | 0.1u | Capacitor_SMD:C_0603_1608Metric_Pad1.08x0.95mm_HandSolder | C2, C5 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric_Pad0.98x0.95mm_HandSolder | R5, R6 |
| 2 | 4.7k | Resistor_SMD:R_0603_1608Metric | R1, R2 |
| 2 | BSS138 | Package_TO_SOT_SMD:SOT-23 | Q1, Q2 |
| 2 | Conn_01x18_Pin | Connector_PinHeader_2.54mm:PinHeader_1x18_P2.54mm_Vertical | J3, J4 |
| 2 | SolderJumper_2_Open | Jumper:SolderJumper-2_P1.3mm_Open_RoundedPad1.0x1.5mm | JP1, JP2 |
| 1 | ADUM3160 | Package_SO:SOIC-16W_7.5x10.3mm_P1.27mm | U3 |
| 1 | CH340K | Package_SO:SSOP-10-1EP_3.9x4.9mm_P1mm_EP2.1x3.3mm | U2 |
| 1 | ESP32-S3-WROOM-1 | RF_Module:ESP32-S3-WROOM-1 | U4 |
| 1 | RT9080N-08GJ5 | footprints:SOT94P280X100-5N | IC1 |
| 1 | TC7W74FU | Yamaha:TC7W53FUF | IC2 |
| 1 | TS5A23159DGS | Package_SO:VSSOP-10_3x3mm_P0.5mm | U1 |
| 1 | USB_C_Receptacle_PowerOnly_6P | Connector_USB:USB_C_Receptacle_GCT_USB4125-xx-x_6P_TopMnt_Horizontal | J2 |
| 1 | USB_C_Receptacle_USB2.0_16P | Connector_USB:USB_C_Receptacle_GCT_USB4105-xx-A_16P_TopMnt_Horizontal | J1 |
| 1 | WS2812B5050 | LED_SMD:LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D4 |
More from Tert2/KiCAD
12- 2 layers100 × 100 mm

- 2 layers83 × 100 mm

- 2 layers58.4 × 68.6 mm

- 2 layers86 × 89 mm

- 2 layers83.3 × 75.6 mm

- 2 layers26.8 × 90 mm

- 2 layers72 × 72 mm

- 2 layers100 × 99 mm

- 2 layers80 × 90 mm

- 2 layers94 × 63 mm

- 2 layers80 × 100 mm

- 2 layers72 × 47.5 mm

Similar boards
- 4 layers72 × 47 mm

- 2 layers100 × 90 mm

- 2 layers380.2 × 121.1 mm

- 2 layers80 × 80 mm

- 2 layers75 × 75.1 mm

- 4 layers80 × 80 mm

- 2 layers131 × 100 mm

Panel
RamRamAndroid/ESP32Drone-CodeMatrix
ESP32 Drone by CodeMatrix is a compact, WiFi-controlled drone based on the ESP32-S3 microcontroller. Designed for hobbyists, makers, and engineers, ESP32 Drone by CodeMatrix offers a simple yet powerful platform for…
182 parts1 - 4 layers72.6 × 35.8 mm

Esp32 cam
akashh218/ESP32-CAM-Devlopment-board
Custom 4-layer ESP32-S3 camera development board designed in KiCad, featuring camera and microSD interfaces, dual USB-C connectivity, UART programming, GPIO expansion, power management, and RF-aware PCB layout.
54 parts
Questions
How big is the ESP32S3 PCB?
It measures 27.9 × 57.2 mm and has 4 copper layers, 1.6 mm thick.
What parts does the ESP32S3 use?
50 parts, built around the ESP32-S3-WROOM-1-N8, CH340K, ADUM3160BRW and RT9080N-08GJ5. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the ESP32S3 KiCad files?
From the Tert2/KiCAD repository on GitHub, at the commit this page was made from: the board is ESP32S3/ESP32S3.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the ESP32S3 design in my own project?
Its repository states no licence, so its author keeps all rights: ask Tert2 before reusing the design.