Skip to the content
2 layers101.6 × 76.2 mmMinimal-6502, the printed circuit board in 3D

Minimal 6502 SBC based on Grant Searle's 8-chip 6502 computer

Size
101.6 × 76.2 mm
Copper layers
2
Thickness
1.6 mm
Parts
37
Nets
89
Pads
335
Tracks, vias
906, 296
Pours
2
Routed
Yes
KiCad
KiCad 8.0 (file 20240108)
Created
27 May 2024
Updated
12 Jun 2024

Overview

Minimal-6502 is an open-source printed circuit board by techav-homebrew, from the techav-homebrew/Minimal-6502 repository on GitHub. It is a 2-layer board of 101.6 × 76.2 mm with 37 parts on 89 nets, routed with 906 tracks and 296 vias.

It is built around the MAX232N, FT230XS-R and 74LS00SC, with the 74LS04PC among its other parts. Its parts include 8 resistors, 8 ICs, 7 capacitors, 5 connectors and 1 switch. It belongs with the retro computing and games boards of this library.

Main components

4

README

README.md

Minimal-6502

Minimal 6502 SBC based on Grant Searle's 8-chip 6502 computer and laid out as a 4x3" PCB.

Modifications from Grant Searle's design include:

  • Addition of expansion header
  • Changed clock from crystal to standard TTL can oscillator
  • Added option for USB for serial & power via FTDI
  • Reassembled software for 8kB EEPROM instead of 16kB EPROM because 27128 EPROM is not readily available (PCB still supports 27128)

Assembly Notes

Part U5, 32kB SRAM, can be either a 7.5mm or 14.5mm width part. If using a 7.5mm package, it should be aligned as indicated on the side closest to the CPU.

Computer can be assembled with either an RS-232 serial port for use with a traditional terminal or USB serial adapter for use with a modern computer as a terminal. Parts related to each option are listed below.

RS-232 DE-9 Serial

  • J1 - DE-9 connector
  • U2 - MAX232 RS-232 level shifter
  • C1, C2, C3, C4 - 100nF capacitor
  • J3 - 2.1mm barrel power connector

USB Serial

  • J2 - USB-B connector
  • U8 - FTDI FT230X
  • R3, R4 - 26-Ohm resistor

Usage Notes

The computer should be powered by USB or via the barrel connector, not both. There is no on-board voltage regulation, so if the barrel connector is used, then the computer should be powered by a regulated 5V power supply.

Serial bit rate is 115200, and backspace should be configured for Control-H (PuTTY defaults to Control-?)

When using a terminal emulator via USB, it may be necessary to press Reset to display the Cold Start prompt.

If no size is entered on the memory size prompt, then the computer will attempt to determine the installed memory size.

Expansion Port Header Pinout

  1. +5V
  2. +5V
  3. +5V
  4. +5V
  5. D0
  6. A0
  7. D1
  8. A1
  9. D2
  10. A2
  11. D3
  12. A3
  13. D4
  14. A4
  15. D5
  16. A5
  17. D6
  18. A6
  19. D7
  20. A7
  21. R/W#
  22. A8
  23. READ#
  24. A9
  25. WRITE#
  26. A10
  27. NMI#
  28. A11
  29. RDY
  30. A12
  31. IRQ#
  32. A13
  33. [Not Connected]
  34. A14
  35. Phi2
  36. A15
  37. Ground
  38. Ground
  39. Ground
  40. Ground

Parts

37
QtyValueFootprintReferences
62K2Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R2, R5, R6, R7, R8
51uFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC1, C2, C3, C4, C5
4MountingHole_PadMountingHole:MountingHole_3.2mm_M3_Pad_ViaH1, H2, H3, H4
3Jumper_3_Bridged12Connector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalJP1, JP2, JP3
227RResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR3, R4
11.8432MHzOscillator:Oscillator_DIP-8X1
1100nFCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P2.50mmC7
110uFCapacitor_THT:CP_Radial_D8.0mm_P5.00mmC6
127128Package_DIP:DIP-28_W15.24mm_SocketU6
174LS00Package_DIP:DIP-14_W7.62mm_SocketU3
174LS04Package_DIP:DIP-14_W7.62mm_SocketU4
1Barrel_Jack_SwitchConnector_BarrelJack:BarrelJack_HorizontalJ3
1CY62256Package_DIP:DIP-28_W15.24mm_SocketU5
1Conn_01x14Connector_PinHeader_2.54mm:PinHeader_1x14_P2.54mm_VerticalJ5
1Conn_02x20_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_HorizontalJ4
1DE9_PlugConnector_Dsub:DSUB-9_Male_EdgeMount_P2.77mmJ1
1FT230XSPackage_SO:SSOP-16_3.9x4.9mm_P0.635mmU8
1MAX232Package_DIP:DIP-16_W7.62mm_SocketU2
1MC68B50Package_DIP:DIP-24_W15.24mm_SocketU1
1R6502Package_DIP:DIP-40_W15.24mm_SocketU7
1SW_PushButton_Switch_THT:SW_PUSH_6mmSW1
1USB_BConnector_USB:USB_B_OST_USB-B1HSxx_HorizontalJ2

Similar boards

  • 2 layers220 × 173.3 mmSF-7017, the printed circuit board in 3D

    SF-7017

    fabiodl/sf7000

    Most of the work was done by Andrea Ottaviani https://github.com/aotta

    68 parts10GPL-3.0
  • 2 layers232.8 × 204.2 mmTIM-011B, the printed circuit board in 3D

    TIM-011B

    Board-Folk/TIM011B

    TIM-011 B Replica Board

    162 parts8
  • 2 layers244 × 244 mm6809PC-6U, the printed circuit board in 3D

    6809PC-6U

    danwerner21/6809PC

    6809 PC

    167 parts2
  • 2 layers150 × 100 mmAPL1, the printed circuit board in 3D

    APL1

    acwright/APL1

    A homebrew Apple 1 replica

    53 parts1CERN-OHL-P-2.0
  • 6 layers244 × 244 mmRetroslop, the printed circuit board in 3D

    Retroslop

    CPTforever/8088-MicroATX-Computer

    A 8088 based, IBM 5150 like computer compatible with the MicroATX motherboard form factor.

    193 parts
  • 4 layers254 × 254 mmProto1, the printed circuit board in 3D

    Proto1

    ehbc-project/ehbc-proto1-board

    KiCad board designs for EHBC

    174 parts
  • 2 layers300 × 200 mmModel 150, the printed circuit board in 3D

    Model 150

    Julesc013/project-carbon

    Hardware and software for custom CPUs, FPUs, and computer systems.

    377 parts
  • 2 layers160.5 × 100.2 mm8080 Board, the printed circuit board in 3D

    8080 Board

    sladek/SBC_8080_ECB

    This is my attempt to build a single-board microcomputer based on the Intel 8080 CPU. It contains the following features:

    112 parts

Questions

How big is the Minimal-6502 PCB?

It measures 101.6 × 76.2 mm and has 2 copper layers, 1.6 mm thick.

What parts does the Minimal-6502 use?

37 parts, built around the MAX232N, FT230XS-R, 74LS00SC and 74LS04PC. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the Minimal-6502 KiCad files?

From the techav-homebrew/Minimal-6502 repository on GitHub, at the commit this page was made from: the board is PCB/Minimal-6502.kicad_pcb and its schematic PCB/Minimal-6502.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the Minimal-6502 design in my own project?

Its repository states no licence, so its author keeps all rights: ask techav-homebrew before reusing the design.