

Wrap030 DRAM
Homebrew 68030 computer
- Size
- 106.7 × 83.8 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 46
- Nets
- 184
- Pads
- 422
- Tracks, vias
- 830, 243
- Pours
- 10
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 31 May 2021
- Updated
- 13 Aug 2026
Overview
Wrap030 DRAM is an open-source printed circuit board by techav-homebrew, from the techav-homebrew/Wrap030 repository on GitHub. It is a 2-layer board of 106.7 × 83.8 mm with 46 parts on 184 nets, routed with 830 tracks and 243 vias.
Its parts include 19 resistors, 10 capacitors and 4 ICs. It belongs with the FPGA and CPLD boards of this library.
README
README.mdWrap030
An ever-evolving homebrew 68030 computer.
Wrap030 got its name from its beginnings. It started as a wire-wrapped single board computer built largely from parts on-hand and what could be acquired locally. It was incredibly unstable.
Since then, it has gone through several major stages, adding new hardware and updating its memory map along the way. It currently exists as a stack of PCBs with a three ribbon cable main bus linking them. Many odd decisions and design constraints carry forward from that initial wire-wrap prototype.
The primary goal of the project is to learn how to build a 32-bit computer from the ground up, and at that it has been incredibly successful. A secondary long-term goal was to build something capable of running a Unix-like operating system, and has had some success there as well.
A rough log of development is tagged wrap030 on techav.net.
Software
Bootloader
ROM bootloader will read & execute BOOT.BIN from a FAT16-formatted CompactFlash card.
MultiBASIC
MultiBASIC is a minimal just-enough-OS kernel for running 8 simultaneous instances of EhBASIC. It uses the 68030 MMU to implement memory protection and supports pre-emptive multitasking.
NetBSD
In early 2025, the project had finally reached a state where it was stable enough and had all of the critical hardware components to try to port a proper operating system. NetBSD was chosen because of its active m68k development and relative ease of understanding. One month was devoted to attempting to port NetBSD to Wrap030 with the result being a functional single-user root shell. Full multi-user booting was not successful. The results of that work are in a separate repo, netbsd-wrap030.
Hardware
Memory Map
| Address | Device | Size/Stride | IRQ | Description |
|---|---|---|---|---|
| 0x00000000 | RAM | 16MB | Main memory, all of lower 2GB reserved for RAM | |
| 0x80000000 | ROM | 128kB | Boot ROM, up to 512kB supported. Overlays 0x0 on reset | |
| 0x80080000 | ACIA | stride 4 | 1 | M6850 ACIA for bootloader & MultiBASIC supervisor |
| 0x80180000 | Overlay | N/A | Write-only register for disabling startup overlay | |
| 0x80200000 | IDE Cmd | stride 2 | 3 | IDE Command registers |
| 0x80202000 | IDE Ctrl | stride 2 | 3 | IDE Control registers |
| 0x80300000 | Com 0 | stride 1 | 5 | 16550-compatible UART |
| 0x80300008 | Com 1 | stride 1 | 5 | 16550-compatible UART |
| 0x80300010 | Com 2 | stride 1 | 5 | 16550-compatible UART |
| 0x80300018 | Com 3 | stride 1 | 5 | 16550-compatible UART |
| 0x80300020 | Com 4 | stride 1 | 5 | 16550-compatible UART |
| 0x80300028 | Com 5 | stride 1 | 5 | 16550-compatible UART |
| 0x80300030 | Com 6 | stride 1 | 5 | 16550-compatible UART |
| 0x80300038 | Com 7 | stride 1 | 5 | 16550-compatible UART |
| 0x80f00000 | Timer | 64kB* | 6 | Write-only timer interval; see below |
| N/A | NMI | N/A | 7 |
Startup Overlay
On reset, ROM is overlaid on top of RAM at address 0x00000000. All reads from the lowest 512k addresses will be passed to ROM instead of RAM. Writes are passed through to RAM.
Writing 0 to the overlay register will disable the startup overlay. Attempting to write to the overlay port again should not be attempted.
IDE Controller
The IDE controller is little more than some buffers on the main bus, with a little glue logic for timing. Data bytes are swapped in hardware. This means byte commands can be sent to the interface unmodified, but 16-bit read/write data needs to be swapped in software.
Custom Interval Timer
The interval timer is a minimal custom design implemented using spare macrocells in the DRAM controller CPLD. Writing to the timer register will start the timer count. It will continue counting until it reaches 0, where it will hold until the count register is written to again. Timer interrupt request is asserted when the count reaches 1 and remains asserted until the count register is written to again. Writing 0 to the count register will disable the timer.
Since the timer is part of the DRAM control logic, it latches the least-significant 16 address bits as the count value. The value on the data bus is ignored.
The countdown runs at main bus frequency, 25MHz, so a count of 25,000 would be roughly a 1ms interval (plus interrupt servicing overhead). The maximum count is 65,535, which would be a little over 2.5ms.
Parts
46| Qty | Value | Footprint | References |
|---|---|---|---|
| 19 | 33R | Wrap030_DRAM:R0805 | R1, R2, R3, R4, R5, R6, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19 +3 |
| 8 | 100n | Wrap030_DRAM:C0805 | C1, C2, C3, C4, C5, C6, C7, C8 |
| 7 | JP2E | Wrap030_DRAM:JP2 | GCLK2, IO5, IO6, IO8, IO11, IO13, OE1 |
| 4 | 74FCT2245 | Wrap030_DRAM:SO20W | IC2, IC3, IC4, IC5 |
| 2 | M20X2SHROUDED | Wrap030_DRAM:2X20_SHROUDED | BUS0, D-LO0 |
| 1 | ATF1508AS | Wrap030_DRAM:S84 | GLUE0 |
| 1 | CPOL-USE2-5 | Wrap030_DRAM:E2-5 | C9 |
| 1 | CPOL-USE3.5-8 | Wrap030_DRAM:E3,5-8 | C17 |
| 1 | L04P | Wrap030_DRAM:L04P | POWER0 |
| 1 | M10X2 | Wrap030_DRAM:2X10 | CTRL0 |
| 1 | SIMM72 | Wrap030_DRAM:73826962 | SIMM0 |
More from techav-homebrew/Wrap030
7- 4 layers106.7 × 83.8 mm

- 2 layers99.1 × 99.1 mm

- 2 layers99.1 × 99.1 mm

- 2 layers106.7 × 99.1 mm

- 2 layers106.7 × 83.8 mm

- 4 layers106.7 × 88.9 mm

- 2 layers106.7 × 83.8 mm

Similar boards
- 2 layers83.3 × 65.3 mm

SimonShield
github-linguist/linguist
Language Savant. If your repository's language is being reported incorrectly, send us a pull request!
46 parts14kMIT - 2 layers27.8 × 22.3 mm

Audio
byrantech/laptop
anyon_e, a highly integrated, high end, open source laptop. Attempt the impossible.
46 parts4.3kMIT - 2 layers370 × 11 mm

Daylight XXL
VoronDesign/Voron-Hardware
Cool Hardware designed by the Voron Design group
46 parts1.1kGPL-3.0 - 2 layers87.5 × 50 mm

- 2 layers38.8 × 62.5 mm

ESPAudio
hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!
46 parts915 - 2 layers53.2 × 24.8 mm

- 2 layers23 × 29 mm

- 2 layers25.5 × 73.5 mm

TERES PCB2-IO Rev.B
OLIMEX/DIY-LAPTOP
Do It Yourself Open Source Hardware and Software Modular Hacker's Friendly Laptop
46 parts578Apache-2.0
Questions
How big is the Wrap030 DRAM PCB?
It measures 106.7 × 83.8 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Wrap030 DRAM use?
46 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Wrap030 DRAM KiCad files?
From the techav-homebrew/Wrap030 repository on GitHub, at the commit this page was made from: the board is ExpansionBoards/Memory/Hardware/Wrap030_DRAM.kicad_pcb and its schematic ExpansionBoards/ATX-PSU_8b/ATX-PSU_8b.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Wrap030 DRAM design in my own project?
Its repository states no licence, so its author keeps all rights: ask techav-homebrew before reusing the design.