
Renewable charger
Tactile-electronics/windmill-electronics
I can't work out how to do the two circuits on one board with the connections that you can add and remove. So I've made two separate boards.

I can't work out how to do the two circuits on one board with the connections that you can add and remove. So I've made two separate boards.
Windmill motor series is an open-source printed circuit board by Tactile-electronics, from the Tactile-electronics/windmill-electronics repository on GitHub, published under the CC0-1.0 licence. It is a 2-layer board with 11 parts on 8 nets.
It belongs with the robots and motor control boards of this library.
I can't work out how to do the two circuits on one board with the connections that you can add and remove. So I've made two separate boards.
I wanted you to have alook before I wire it up on Kicad as at the moment I'm not sure if I've got it right and some connections seem wrong
e.g the connections out of the board that is in series have been connected together on the pcb - by KICAD - do I need to change it in the schematic or can I do that in the wiring?
| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | CP | Capacitors_THT:CP_Radial_Tantal_D8.0mm_P5.00mm | Cap_Radial1, Cap_Radial2, Cap_Radial3, Cap_Radial4 |
| 2 | -Out | Connectors_WAGO:WAGO_734_2pin_Straight_RuggedPads | +Out1, +Out2 |
| 2 | DIP 4 Pins | Diodes_THT:Diode_Bridge_DIP-4_W7.62mm_P5.08mm | BridgeRectifier1, BridgeRectifier2 |
| 1 | +ve tie | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP1 |
| 1 | -ve tie | Jumper:SolderJumper-2_P1.3mm_Bridged_RoundedPad1.0x1.5mm | JP2 |
| 1 | Stepper_Motor_bipolar | Connectors_TE-Connectivity:TE_MATE-N-LOK_350211-1_1x04_P5.08mm_Vertical | StepperMotor1 |

Tactile-electronics/windmill-electronics
I can't work out how to do the two circuits on one board with the connections that you can add and remove. So I've made two separate boards.

Tactile-electronics/windmill-electronics
I can't work out how to do the two circuits on one board with the connections that you can add and remove. So I've made two separate boards.

Tactile-electronics/windmill-electronics
I can't work out how to do the two circuits on one board with the connections that you can add and remove. So I've made two separate boards.

google/mozc-devices
Circuit diagrams and firmware source code for Gboard DIY keyboards


FrameworkComputer/ExpansionCards
Reference designs and documentation to create Expansion Cards for the Framework Laptop

hoglet67/RGBtoHDMI
Bare-metal Raspberry Pi project that provides pixel-perfect sampling of Retro Computer RGB/YUV video and conversion to HDMI

hackclub/OnBoard
💡 Join 1,000 teenagers and make your first PCB with a $100 grant!


tardate/LittleArduinoProjects
a collection of "Little Electronic & Arduino Projects", most involving electronics or an Arduino in one way or another!

basilfx/TRADFRI-Hacking
Hacking IKEA TRÅDFRI products, such as light bulbs, window blinds and other accessories.
11 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Tactile-electronics/windmill-electronics repository on GitHub, at the commit this page was made from: the board is Series Circuit/windmill motor series.kicad_pcb and its schematic renewable-charger/renewable-charger.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository publishes it under the CC0-1.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).