Skip to the content
2 layers227.6 × 181.3 mmXY Reg Ver.2, the printed circuit board in 3D

8-Bit Relay Computer inspired by Harry Porter and DipDot

Size
227.6 × 181.3 mm
Copper layers
2
Thickness
1.6 mm
Parts
146
Nets
292
Pads
630
Tracks, vias
1,800, 184
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
25 Jun 2025
Updated
1 Oct 2026

Overview

XY Reg Ver.2 is an open-source printed circuit board by Syntaxer04, from the Syntaxer04/RC1Computer repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 227.6 × 181.3 mm with 146 parts on 292 nets, routed with 1,800 tracks and 184 vias.

Its parts include 54 diodes, 34 switches, 20 resistors and 6 connectors.

README

README.md

RC1Computer

8-Bit Relay Computer inspired by Harry Porter and DipDot

General Information

This Computer, inspired Harry H Porter III, Ph.D, Paul Law, and Youtuber DipDot, is (almost) completly made out of relays, 607 of them to be exact.

Specifications

  • 32 kb RAM
  • It has 11 15 8 Bit Registers. Some of them can also funtcion as 16 Bit Registers.
  • A clock rate Between 3 and 8 Hertz
  • 8 Bit Data and Instruction Bus, as well as an 16* Bit Adress Bus *only 15 bits are actually used, but the 16th Bit is still usable for other Peripherals/More Memeory

Changes in V0.2

  • Changed how I managed the Bus on the RC-1. The Bus Board now encompasses all Register Signals and otherwise, except for the Timing pulses, which is only used by the Controller.
  • Caught most the Routing mistakes I made in the first Version. The second run really helped spotting obvious and not so obvious mistakes.
  • Added a board for the front panel functions. The switches are not mounted on the Board however, and so are the LEDs.
  • I also started experimenting with Capacitor Storage. I included my initial design in this version.
  • The memory board had an overhaul, with more isolation and better logic.
  • The ALU has been split into two boards. I was able to do this because of the new backplane.

Future features

  • I want to make some sort Storage medium. A Tape interface, similar to DipDot's design, would be nice, although for a computer like that kind of lame in my opinion. I am thinking more like a paper based interface, like the one Usagi electric build for the UE1. One Slight Problem thogh: Reading may be somewhat easy, the writing on the other hand may be a little challenge... We'll burn that bridge when we get there.
  • Tape Loader has been added, function not Tested however.
  • The Second thing i want to make for this project is some sort of Serial/ Terminal output. That itself is not that hard all things considered, it's nearly a chip solution. The real problem is that the Computer most likely lacks any sort of speed for that kind of outpu. So i either have to buffer the output, make it exceptionaly slow, or find some other way of sending a serial signal of of the Computer.

Links

Paul Law´s Youtube channel, and his personal Blog. Harry Porter´s Webiste, specifically, this PDF. Lastly, DipDot´s Youtube channel. He was the main inspiration for this project and his videos are well made.

Parts

146
QtyValueFootprintReferences
341N914Diode_THT:D_DO-35_SOD27_P7.62mm_HorizontalD1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +18
34HK19F-DCxxV-SHCrelaccomp:Relay_DPDT_Finder_30.22 ohne SilkSK1, K2, K10, K11, K12, K13, K14, K15, K16, K17, K18, K19, K20, K21, K22, K23 +18
32SolderJumper_2_OpenJumper:SolderJumper-2_P1.3mm_Open_Pad1.0x1.5mmJP1, JP2, JP10, JP11, JP12, JP13, JP14, JP15, JP16, JP17, JP18, JP19, JP20, JP21, JP22, JP23 +16
20RResistor_THT:R_Axial_DIN0204_L3.6mm_D1.6mm_P7.62mm_HorizontalR1, R2, R3, R4, R5, R10, R11, R12, R13, R14, R15, R16, R17, R18, R19, R20 +4
19LEDrelaccomp:LED_D5.0mm ohne SilkSD51, D52, D53, D54, D55, D56, D57, D58, D59, D60, D61, D62, D63, D64, D65, D66 +3
2Conn_02x20_Counter_ClockwiseConnector_PinSocket_2.54mm:PinSocket_2x20_P2.54mm_HorizontalJ1, J2
1Conn_01x04_PinConnector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_VerticalJ4
1Conn_01x38_PinConnector_PinHeader_2.54mm:PinHeader_1x38_P2.54mm_VerticalJ3
1Conn_02x02_Counter_ClockwiseConnector_PinSocket_2.54mm:PinSocket_2x02_P2.54mm_VerticalJ61
1Conn_02x10_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x10_P2.54mm_HorizontalJ5
1LEDLED_THT:LED_D5.0mmD69

More from Syntaxer04/RC1Computer

12
  • 2 layers253.4 × 291.8 mmCond.memory, the printed circuit board in 3D

    Cond.memory

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    398 parts4GPL-3.0
  • 2 layers277.2 × 203.3 mmFront Panel, the printed circuit board in 3D

    Front Panel

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    223 parts4GPL-3.0
  • 2 layers202.4 × 140.2 mmALU, the printed circuit board in 3D

    ALU

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    196 parts4GPL-3.0
  • 2 layers172.5 × 226.3 mmALU V2 v2 - Logik, the printed circuit board in 3D

    ALU V2 v2 - Logik

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    172 parts4GPL-3.0
  • 2 layers202.4 × 169.6 mmIncrementer, the printed circuit board in 3D

    Incrementer

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    169 parts4GPL-3.0
  • 2 layers231.2 × 156.8 mmController V2, the printed circuit board in 3D

    Controller V2

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    169 parts4GPL-3.0
  • 2 layers202.5 × 144.2 mmFulladder, the printed circuit board in 3D

    Fulladder

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    162 parts4GPL-3.0
  • 2 layersTape loader, the printed circuit board in 3D

    Tape loader

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    142 parts4GPL-3.0
  • 2 layers170.9 × 161.2 mmALU V2, the printed circuit board in 3D

    ALU V2

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    141 parts4GPL-3.0
  • 2 layers170 × 180 mmIncrementer V2 - Register, the printed circuit board in 3D

    Incrementer V2 - Register

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    126 parts4GPL-3.0
  • 2 layers202.3 × 144.4 mmController, the printed circuit board in 3D

    Controller

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    123 parts4GPL-3.0
  • 2 layers219.8 × 145.4 mmDecoder V2, the printed circuit board in 3D

    Decoder V2

    Syntaxer04/RC1Computer

    8-Bit Relay Computer inspired by Harry Porter and DipDot

    122 parts4GPL-3.0

Similar boards

  • 2 layers104 × 66 mmLCD DRIVER Rev D, the printed circuit board in 3D

    LCD DRIVER Rev D

    OLIMEX/OLINUXINO

    OLINUXINO is Open Source / Open Hardware, low cost from EUR 24 Linux Industrial grade Single Board Computer capable to operate -25+85C

    146 parts1.5k
  • 2 layers58 × 110 mmVco core, the printed circuit board in 3D

    Vco core

    shmoergh/moduleur

    Fully analog DIY-friendly modular synth

    146 parts222
  • 2 layers65 × 145 mmPcb v1 1, the printed circuit board in 3D

    Pcb v1 1

    EleonoreMizo/pedalevite

    Pédale Vite — DIY multi-FX pedalboard for guitar/bass/etc.

    146 parts101WTFPL
  • 2 layers40 × 100 mmWhiteRabbit, the printed circuit board in 3D

    WhiteRabbit

    ThisIsNotRocketScience/Eurorack-Modules

    This is not Rocket Science presents: Eurorack modular synthesizer modules!

    146 parts87MIT
  • 2 layers103.9 × 43.5 mmCps2 digiav, the printed circuit board in 3D

    Cps2 digiav

    marqs85/cps2_digiav

    CPS2 digital AV interface

    146 parts49
  • 2 layers101.6 × 50.8 mmNigun 0603, the printed circuit board in 3D

    Nigun 0603

    raziele/Nigun

    1.5-3GHz RF down-converter for RTL-SDR

    146 parts40
  • 2 layers271.8 × 103.9 mmHotswap ble, the printed circuit board in 3D

    Hotswap ble

    ebastler/cornholius

    ZMK-based replacement PCB for Cornelius keyboard

    146 parts37
  • 2 layers128 × 80 mmModularLabPSU, the printed circuit board in 3D

    ModularLabPSU

    tom-biskupic/LabPSU

    Open Source Lab Power Supply

    146 parts33

Questions

How big is the XY Reg Ver.2 PCB?

It measures 227.6 × 181.3 mm and has 2 copper layers, 1.6 mm thick.

What parts does the XY Reg Ver.2 use?

146 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the XY Reg Ver.2 KiCad files?

From the Syntaxer04/RC1Computer repository on GitHub, at the commit this page was made from: the board is Version 0.2/XY-reg 2/XY-Reg Ver.2/XY-Reg Ver.2.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the XY Reg Ver.2 design in my own project?

Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).