Skip to the content
2 layers120 × 50 mmCreatureControl5x12-1.2, the printed circuit board in 3D

CreatureControl5x12-1.2

swaziloo/halloween9

Halloween Projects

Size
120 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
50
Nets
40
Pads
166
Tracks, vias
262, 40
Pours
2
Routed
Yes
KiCad
KiCad 9.0 (file 20241229)
Created
29 Aug 2025
Updated
9 Feb 2026

Overview

CreatureControl5x12-1.2 is an open-source printed circuit board by swaziloo, from the swaziloo/halloween repository on GitHub, published under the MIT licence. It is a 2-layer board of 120 × 50 mm with 50 parts on 40 nets, routed with 262 tracks and 40 vias.

Its parts include 12 capacitors, 3 resistors, 3 connectors and 2 diodes. It belongs with the RP2040 boards of this library.

README

creatureControl/README.md

The Creature Control 5x12 PCB

Creature Control PCB

When hand soldering a board to enable the animatronic crow I realized that I wanted a half-dozen crows and maybe some talking skulls and hand soldering wasn't my favorite way to spend my time. Hence Creature Control 5x12. Designed to enable a bunch of capability using an inexpensive and easy to program Raspberry Pi 2040 in the tiny Waveshare Zero format.

I likely have extra PCBs—contact me directly if interested in PCB(s) at cost.

Versions 1.0-1.2 of the CC5x12 PCB

5x12 v1.0

Provides a 5-volt 3-amp power rail to supply 3 servos and 2 steppers controlled by a RP2040-Zero which is also wired to incorporate 2 LEDs, 2 motion sensors, the DFPlayer Mini mp3 player and a pin header for the remaining pins. Designed to be hand-soldered and easily programmable using Arduino libraries.

v1.1 2025-09

Larger PTH (0.9mm) for MCU and mp3 player mounts, add 1KΩ serial resistor for DFPlayer RX (MCU GP0) connection, add capacitor (104) for DFPlayer 3V3, remove incorrect silk for C7 and C8 value, rotate sensor mounts for better routing, update schema.

v1.2 2025-10

Move DFPlayer Mini to 5V supply and add additional bulk/filtering capacitors (1µF, 220µF), add filtering capacitor (0.1µF) at 5V power supply, move servos 1-3 to GP27-GP29, move GP2-GP4 to expansion header, rotate DFPlayer Mini, (re)arrange silks, update schema.

Gerber files have been produced for JLCPCB but may work elsewhere.

Animatronic Crow build on CC5x12

VITAL IMPORTANT SAFETY NOTICE!

The 5 volt power rail allows for multiple source connections but only one should be used at any given time. Do not connect more than one 5 volt source to the power rail! (Unless you really know what you're doing.) It is safe to connect the power to the 5v rail and the RP2040-Zero to your PC at the same time—in fact it's necessary for testing.

Parts List

The intent is that one would install only the components needed for a project.

QtyRefPartNote
1RP2040-ZeroWaveshare or equivalent.
1D21N5819 Schottky DiodeFor RP2040-Zero VCC.
1DFPlayer MiniDFRobot or equivalent.
3-4C7-C9, C12100nF 50v Ceramic Capacitor (104)(v1.1+) for DFPlayer Mini 5V, (v1.2) input 5V, ULN2003A.
1C101µF 50v Ceramic Capacitor (105)(v1.2) For DFPlayer Mini midrange filter.
1C11220µF 10-16v Electrolytic Capacitor(v1.2) For DFPlayer Mini .
1R61KΩ Resistor(v1.1+) for MCU GP0->DFPlayer Mini RX
1-2ULN2003AStepper driver.
1-2 (optional)IC DIP Socket 16-PinFor ULN2003A. Or just solder directly to the board.
1-2XH2.54mm 5-Pin ConnectorStraight pin for stepper.
1 (optional)D13mm LEDFor power rail indicator.
1 (optional)R3Resistor for power indicator LEDI used 2.2kΩ for a blue 3mm LED.
1-2R4,R5Resistor for external LEDsBased on LED(s) to be used.
1-5C2-C6100µF 10-16v Electrolytic CapacitorOne for each 5v servo and stepper.
1C11000µF 10-16v Electrolytic CapacitorFor 5v rail.
1 (optional)J25.5x2.1MM DC-005 Power JackIf using a 5v/3A adapter.
1 (optional)J1USB-C 6-pin Surface MountIf using a USB battery.
2 (optional)R1,R25.1kΩ ResistorsIf using a USB battery.
1 (optional)J3KF350-2P 3.5mm Pitch 2Pin PCB Screw Terminal Block ConnectorIf using a wired 5v source or drain. Also useful if needing to share ground with an external power rail.
optional2.54mm Pin HeadersFor board connections.

Building the CC5x12

  • You do not need to fill the board. It is perfectly acceptable to install only the connections and components you intend to use.
  • If you are installing the USB-C socket, do that first and test the electrical connections. Every other component is easier to hand solder.
  • The RP2040-Zero can be powered by its USB-C connection or the board 5v power, but it will not provide power to the steppers, servos, or DFPlayer (since v1.2). LEDs and sensors draw power from the RP2040-Zero 3V3.
  • The C1 capacitor is intended to smooth out the 5v supply for the board. C2-C6 & C11 provide demand power for their nearby stepper, servo, or DFPlayer Mini. Only install these caps for the components you intend to connect.

Testing

Install the Arduino IDE and the following libraries: AccelStepper, DFRobotDFPlayerMini, arduino-pico by Earle Philhower, Adafruit NeoPixel. Install using the library manager in the Arduino IDE.

  • Enable the Waveshare RP2040-Zero board in the board manager.
  • Connect power to one of the 5v inputs and the RP2040-Zero to your pc.
  • Select the connected device/port and ensure the Waveshare RP2040-Zero board is assigned.
  • Open the BoardTest sketch with the Arduino IDE.
  • Set 'true' for available components at the top of the sketch.
  • Select the 'Upload' button.
  • The sketch should compile, the board should initialize, and a test loop should run.

The steppers, servos, and MP3 components will cycle. The LED(s) will reflect the sensor(s) states.


Notes and Issues:

Volume Issues v1.0 and v1.1

The DFPlayer Mini is being powered off the RP2040-Zero 3V3 on these boards which doesn't provide enough power to handle max draw at high volume. The fix for these boards is to pull the VCC pin from the header and wire to a nearby 5V connection. Add a 220µF electrolytic and a 1µF (105) ceramic at the power tap and pull a twisted pair of 5V/GND to the DFPlayer, connecting a 0.1µF (104) between ground and VCC at the connection point. The easier fix is to lower the volume to one that the MCU will support. Around 22-25/30. TX/RX are already shifted to 3.3V for compatibility with MCU communication.

Connecting to a 12v Rail

You should be able to control 12v steppers and servos using the CC5X12 by eliminating the 5v connection to them and providing separate power. If you do this, you will want to pull a shared ground over from the block connector or another board source. I have not tested this functionality.

Parts

50
QtyValueFootprintReferences
6CP_Radial_D5.0mm_P2.50mmCapacitor_THT:CP_Radial_D5.0mm_P2.50mmC2, C3, C4, C5, C6, C11
5PinHeader_1x03_P2.54mm_VerticalConnector_PinHeader_2.54mm:PinHeader_1x03_P2.54mm_VerticalSNSR1, SNSR2, SRV1, SRV2, SRV3
4PinHeader_1x02_P2.54mm_VerticalConnector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical5V, LED1, LED2, SPKR
32.2 kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_Horizontal R5, R3, R4
35.1 kΩResistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P7.62mm_HorizontalR1, R2, R6
3C_Disc_D5.0mm_W2.5mm_P5.00mmCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC9, C10, C12
210nfCapacitor_THT:C_Disc_D5.0mm_W2.5mm_P5.00mmC7, C8
2DIP-16_W7.62mmPackage_DIP:DIP-16_W7.62mmULN2003A 1, ULN2003A 2
2JST_XH_B5B-XH-A_1x05_P2.50mm_VerticalConnector_JST:JST_XH_B5B-XH-A_1x05_P2.50mm_VerticalSTEPPER1, STEPPER2
1BarrelJack_HorizontalConnector_BarrelJack:BarrelJack_HorizontalJ2
1CP_Radial_D10.0mm_P5.00mmCapacitor_THT:CP_Radial_D10.0mm_P5.00mmC1
1DFPlayer Minicayenne:DFPlayer MiniDFPlayer Mini
1D_DO-41_SOD81_P7.62mm_HorizontalDiode_THT:D_DO-41_SOD81_P7.62mm_HorizontalD2
1LED_D3.0mmLED_THT:LED_D3.0mmD1
1LOGOCreatureControl:Bats02G***
1LOGOCreatureControl:GraveyardLeftG***
1LOGOcayenne:Crow-FlyingG***
1LOGOCreatureControl:GraveyardRightG***
1LOGOcayenne:Crow-Flying2G***
1LOGOCreatureControl:HalloweenMoonG***
1LOGOcayenne:Pumpkin01G***
1LOGOcayenne:Crow-Standing01G***
1RP2040 Zerocayenne:RP2040 ZeroRP2040-Zero
1TerminalBlock_4Ucon_1x02_P3.50mm_HorizontalTerminalBlock_4Ucon:TerminalBlock_4Ucon_1x02_P3.50mm_HorizontalJ3
1USB_C_Receptacle_GCT_USB4125-xx-x-0190_6P_TopMnt_HorizontalConnector_USB:USB_C_Receptacle_GCT_USB4125-xx-x-0190_6P_TopMnt_HorizontalJ1

The 46 most common of 50 parts.

Similar boards

  • 2 layers187.2 × 26.6 mmBlade12, the printed circuit board in 3D

    Blade12

    opulo-inc/lumenpnp

    The LumenPnP is an open source pick and place machine.

    50 parts3.7k
  • 2 layers45.7 × 25.9 mmAccessory, the printed circuit board in 3D

    Accessory

    usbarmory/usbarmory

    USB armory - The open source compact secure computer

    50 parts1.5k
  • 2 layers21 × 31.5 mmK1-aioc, the printed circuit board in 3D

    K1-aioc

    skuep/AIOC

    Ham Radio All-in-one-Cable

    50 parts1.4kMIT
  • 2 layers42 × 32.5 mmLipoboard, the printed circuit board in 3D

    Lipoboard

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    50 parts915
  • 2 layers101 × 31.5 mmManagement, the printed circuit board in 3D

    Management

    dennisss/dacha

    Monorepo for awesome tools/projects/libraries

    50 parts397Apache-2.0
  • 2 layers123.9 × 94.4 mmRoba R, the printed circuit board in 3D

    Roba R

    kumamuk-git/roBa

    50 parts363GPL-3.0
  • 2 layers50 × 25 mmMbus master, the printed circuit board in 3D

    Mbus master

    roarfred/AmsToMqttBridge

    Minimalistic system to read AMS/HAN data from electrical meter

    50 parts223

Questions

How big is the CreatureControl5x12-1.2 PCB?

It measures 120 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the CreatureControl5x12-1.2 use?

50 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the CreatureControl5x12-1.2 KiCad files?

From the swaziloo/halloween repository on GitHub, at the commit this page was made from: the board is creatureControl/CreatureControl5x12-1.2.kicad_pcb and its schematic creatureControl/CreatureControl5x12-1.2.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the CreatureControl5x12-1.2 design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).