
Bias controller
loxodes/vna
Under development open hardware microwave vector network analyzer

Hey everyone, this is my split keyboard project.
SplitKeyboard is an open-source printed circuit board by Sumqz, from the Sumqz/Sumqz-s-Split-Keyboard repository on GitHub. It is a 2-layer board of 339.2 × 144.7 mm with 203 parts on 170 nets, routed with 827 tracks and 32 vias.
Its parts include 87 diodes, 87 switches, 8 resistors, 4 ICs and 2 capacitors. It belongs with the keyboards and input boards and the nRF52 and nRF5x boards of this library.
Hey everyone, this is my split keyboard project.
I always felt that traditional keyboards were functional but boring, so I decided to build my own. It can work as two separate halves or snap together with magnets to become a full 75% style keyboard in seconds.
It is hot-swappable, uses nRF52840 boards, and is designed to be easy to build at home.
I sanity-checked this design with my friend before finalizing it.
A DIY wireless split keyboard with magnetic attachment and hot-swap sockets.

| Part | Qty | Notes | Link |
|---|---|---|---|
| nRF52840 (XIAO nRF52840) | 2 | One per side | Buy |
| MCP23017 GPIO Expander | 2 | MCP23017_SP, DIP-28 package required | Buy |
| LiPo 1200mAh | 2 | One per side | Buy |
| Buzzer 12x9.5 / RM7.6 | 2 | Match PCB footprint pin spacing | Buy |
| Switches (Holy Panda) | 87 | Total keys | Buy |
| Keycaps (generic) | 87 | Match your layout | Buy |
| Diodes 1N4148W (SOD-123) | 87 | One per switch | Buy |
| Resistor 4.7k (0805) | 4 | R1, R2, R5, R6 | Buy |
| Resistor 806k (0805) | 2 | R3, R7 | Buy |
| Resistor 2M (0805) | 2 | R4, R8 | Buy |
| Magnets 6x2 | 8 | 2 per hole | Buy |
| M3 screw + nut | 4 | 40 mm | Buy |
| M4 screw | 4 | 50 mm | Buy |
| M4 nut | 4 | M4 | Buy |
| Hotswap sockets | 87 | choc | But |
PCB and case are not included because they are custom-made.
Resistor note: it is usually cheaper to buy one full 0805 resistor assortment than to buy each value separately.
Flash the .ino firmware to both nRF52840 boards. Then connect each half to your PC and test that every key works.
You can use it as a split keyboard, or snap both halves together with magnets to use it like a full 75% style board.
Firmware source: Firmware/SplitKeyboard/SplitKeyboard.ino
| Qty | Value | Footprint | References |
|---|---|---|---|
| 87 | D | Diode_SMD:D_SOD-123 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +71 |
| 77 | SW_Push | PCM_marbastlib-choc:SW_choc_v1_HS_CPG135001S30_1u | SW1, SW2, SW10, SW11, SW13, SW14, SW15, SW16, SW17, SW19, SW20, SW21, SW22, SW23, SW25, SW26 +61 |
| 5 | TestPoint | TestPoint:TestPoint_Pad_D2.0mm | TP1, TP2, TP2, TP3, TP4 |
| 4 | 4.7K | Resistor_SMD:R_0805_2012Metric | R1, R2, R5, R6 |
| 4 | MountingHole | MountingHole:MountingHole_3.2mm_M3 | H5, H6, H7, H8 |
| 4 | MouseBite | Panelization:MouseBite-Slot_2.0x4.5mm_inset_D0.5mm_P0.85mm_5h_Trace | B2, B3, B4, B8 |
| 3 | SW_Push | PCM_marbastlib-choc:SW_choc_v1_HS_CPG135001S30_1.25u | SW6, SW12, SW18 |
| 3 | SW_Push | PCM_marbastlib-choc:SW_choc_v1_HS_CPG135001S30_2.25u | SW5, SW24, SW75 |
| 2 | 100nF c.Cap. | Capacitor_SMD:C_0805_2012Metric | C1, C2 |
| 2 | 2M | Resistor_SMD:R_0805_2012Metric | R4, R8 |
| 2 | 806K | Resistor_SMD:R_0805_2012Metric | R3, R7 |
| 2 | Buzzer | Buzzer_Beeper:Buzzer_12x9.5RM7.6 | BZ1, BZ2 |
| 2 | MCP23017_SP | Package_DIP:DIP-28_W7.62mm | U1, U3 |
| 2 | SW_Push | PCM_marbastlib-choc:SW_choc_v1_HS_CPG135001S30_1.75u | SW4, SW76 |
| 2 | SW_Push | PCM_marbastlib-choc:SW_choc_v1_HS_CPG135001S30_1.5u | SW3, SW80 |
| 2 | Seeeduino Xiao nRF52840 | PCM_marbastlib-xp-promicroish:Xiao_nRF52840_ACH | U2, U4 |

loxodes/vna
Under development open hardware microwave vector network analyzer

ThisIsNotRocketScience/Eurorack-Modules
This is not Rocket Science presents: Eurorack modular synthesizer modules!

pierrebaillargeon/Microplate-Assistive-Pipetting-Light-Emitter
Microplate Assistive Pipetting Light Emitter (M.A.P.L.E.)


hw-tinkerers/TR-60
kicad files of custom 60% keyboard inspired by bakeneko with ble support


It measures 339.2 × 144.7 mm and has 2 copper layers, 1.6 mm thick.
203 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
From the Sumqz/Sumqz-s-Split-Keyboard repository on GitHub, at the commit this page was made from: the board is PCB/PCB+Schematic/SplitKeyboard.kicad_pcb and its schematic PCB/PCB+Schematic/Schematic.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Its repository states no licence, so its author keeps all rights: ask Sumqz before reusing the design.