

Dummyload
Open-source electronic dummy load for testing high-voltage linear power supplies (tube amplifier PSUs). Adjustable current load, measurement and protection. Includes PCB, firmware and enclosure.
- Size
- 72 × 108 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 65
- Nets
- 52
- Pads
- 163
- Tracks, vias
- 432, 24
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 9.0 (file 20241229)
- Created
- 25 Dec 2025
- Updated
- 12 Mar 2026
Overview
Dummyload is an open-source printed circuit board by STWuRCA-diy, from the STWuRCA-diy/DUMMYLOAD_V2 repository on GitHub. It is a 2-layer board of 72 × 108 mm with 65 parts on 52 nets, routed with 432 tracks and 24 vias.
It is built around the LM358, LM78L05 and 1.5KE13CA. Its parts include 23 connectors, 10 capacitors, 10 resistors, 7 diodes and 4 transistors.
Main components
3LM358
SOP-8-18V~18V 0℃~+70℃ 1.2MHz 10nA 2 24mA 3V~36V 500uA 50nA 5mV 80dB Built-in compensation SOP-8 Operational Amplifier ROHSMSKSEMIOperational AmplifierLM78L05
SOT-89-3-55℃~+125℃@(Tj) 1 1.7V 100mA 20V 42uV 49dB@(120Hz) 5V 6mA Fixed Positive SOT-89-3 Voltage Regulators - Linear, Low Drop Out (LDO) Regulators ROHSKEXINVoltage Regulators - Linear, Low Drop Out (LDO) Regulators1.5KE13CA
DO-201-55℃~+175℃ 1.5kW@10/1000us 11.1V 13.7V 18.2V 1uA 83.5A@10/1000us Bidirectional IEC 61000-4-2、IEC 61000-4-4 TVS DO-201 ESD and Surge Protection (TVS/ESD) ROHSLittelfuseESD And Surge Protection (TVS/ESD)
README
README.mdIMPORTANT!
Unfortunately, I did not have enough time to verify whether the shared version of the board contains any errors. This is a hobby project and I also had to focus on my day job.
I hope someone from the community will be able to review the design, confirm that everything is correct, or fix any mistakes I may have left behind.
The first version of the board did not include many of the components that are present in the shared version. However, all of them were tested using bodge wiring and then added to the shared design.
Good luck!
DUMMYLOAD_V2
High-Voltage Electronic Dummy Load (Non-Commercial, Open-Source)
DUMMYLOAD_V2 is an open-source, non-commercial electronic dummy load designed for testing high-voltage linear power supplies, especially those used in tube (valve) amplifier circuits.
The project includes hardware (PCB), firmware, and mechanical enclosure, forming a complete DIY measurement and load solution for HV power supply development and testing.
Key Features • Adjustable constant-current load • High-voltage measurement via resistor divider • Current measurement using INA219 • Protection logic implemented in firmware • Stand-alone operation (no PC required)
Electrical Characteristics • Load mode: Constant Current (CC) • Current regulation range: 0 – ~400 mA (firmware-controlled, step-based) • Voltage measurement
⚠️ HIGH VOLTAGE WARNING
This project is intended for experienced users.
High voltages used in tube power supplies can be lethal.
• Use proper insulation and creepage distances
• Never touch the circuit during operation
• The author assumes no responsibility for misuseIf you are not comfortable working with HV — do not build or use this device.
⸻
📜 License (Very Important)
🔒 Non-Commercial Only
This entire project is licensed under:
Creative Commons Attribution-NonCommercial 4.0 International (CC BY-NC 4.0)
🍺 Friendly Note
If you ever meet me in person and find this project useful, you owe me a beer.
If we happen to be in a country where it is legal, a joint is also acceptable 🙂
This is a friendly gesture — not a legal obligation.
⸻
❤️ Credits
Designed and shared by STWuRCA-diy DIY spirit, tube amps & open hardware 🤘
Parts
65| Qty | Value | Footprint | References |
|---|---|---|---|
| 4 | 100nF | Capacitor_THT:C_Disc_D3.0mm_W2.0mm_P2.50mm | C6, C7, C9, C10 |
| 4 | 1N4007 | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D1, D2, D3, D4 |
| 4 | 1uF | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C2, C3, C4, C5 |
| 3 | 2N3904 | Package_TO_SOT_THT:TO-92_Inline | Q2, Q3, Q4 |
| 3 | 470 | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R3, R5, R7 |
| 3 | SANYOU_SRD_Form_C | Relay_THT:Relay_SPDT_SANYOU_SRD_Series_Form_C | K1, K2, K4 |
| 2 | 10K | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R2, R10 |
| 2 | 1k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R6, R8 |
| 2 | LM78L05 | Package_TO_SOT_THT:TO-92_Inline | U3, U4 |
| 2 | SWITCH | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J20, J22 |
| 1 | +12V | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J7 |
| 1 | -IN_GND | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J8 |
| 1 | 1.5KE13CA | Diode_THT:D_DO-41_SOD81_P10.16mm_Horizontal | D6 |
| 1 | 1000uF | Capacitor_THT:CP_Radial_D8.0mm_P5.00mm | C8 |
| 1 | 100k | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R1 |
| 1 | 10OHM_1 | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J9 |
| 1 | 10OHM_2 | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J10 |
| 1 | 15V | Diode_THT:D_A-405_P10.16mm_Horizontal | D8 |
| 1 | 16N70C2 | Package_TO_SOT_THT:TO-220-3_Vertical | Q1 |
| 1 | 1M | Resistor_THT:R_Axial_DIN0207_L6.3mm_D2.5mm_P10.16mm_Horizontal | R9 |
| 1 | 1M | Potentiometer_THT:Potentiometer_Vishay_T73YP_Vertical | RV1 |
| 1 | 2.2uF | Capacitor_THT:CP_Radial_D4.0mm_P2.00mm | C1 |
| 1 | 47k/5W | Resistor_THT:R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R4 |
| 1 | 5V | Diode_THT:D_A-405_P7.62mm_Horizontal | D5 |
| 1 | AC_LINE_1 | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J15 |
| 1 | AC_LINE_2 | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J16 |
| 1 | AC_NEUT_1 | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J18 |
| 1 | AC_NEUT_2 | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J17 |
| 1 | GND | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J19 |
| 1 | HV_GND | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J4 |
| 1 | HV_IN | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J1 |
| 1 | INA219_1 | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J11 |
| 1 | INA219_GND | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J23 |
| 1 | INA_B+ | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J12 |
| 1 | L | Connector_PinHeader_2.54mm:PinHeader_1x15_P2.54mm_Vertical | J6 |
| 1 | LCD | Connector_PinHeader_2.54mm:PinHeader_1x04_P2.54mm_Vertical | J2 |
| 1 | LM358 | Package_DIP:CERDIP-8_W7.62mm_SideBrazed | U2 |
| 1 | NCODER | Connector_PinHeader_2.54mm:PinHeader_1x05_P2.54mm_Vertical | J3 |
| 1 | P | Connector_PinHeader_2.54mm:PinHeader_1x15_P2.54mm_Vertical | J5 |
| 1 | SCL_INA | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J14 |
| 1 | SDA_INA | Connector_Wire:SolderWire-0.5sqmm_1x01_D0.9mm_OD2.1mm | J13 |
| 1 | VOL_SW | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J21 |
The 61 most common of 65 parts.
Similar boards
- 4 layers84.1 × 66 mm

- 2 layers

- 2 layers40.5 × 55.4 mm

- 2 layers68.5 × 70 mm

- 2 layers132.1 × 45.7 mm

IPoS
peterheinrich/InternetOverSpaghetti
Transmitting IP packages over a pair of spaghetti thus demonstrating how media independent IP really is.
42 parts342 - 2 layers68.8 × 53.6 mm

ZArduino
zmaker/arduino_cookbook
gli sketch del nuovo progetto Arduino Cookbook e dei video di YouTube
46 parts269 - 2 layers152 × 88 mm

RFBitBangSMT
profdc9/RFBitBanger
A QRP digital transceiver created from readily available parts for off-the-grid maintenance
271 parts222 - 2 layers118 × 103.5 mm

Questions
How big is the Dummyload PCB?
It measures 72 × 108 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Dummyload use?
65 parts, built around the LM358, LM78L05 and 1.5KE13CA. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Dummyload KiCad files?
From the STWuRCA-diy/DUMMYLOAD_V2 repository on GitHub, at the commit this page was made from: the board is KICAD/dummyload.kicad_pcb and its schematic KICAD/dummyload.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Dummyload design in my own project?
Its repository states no licence, so its author keeps all rights: ask STWuRCA-diy before reusing the design.