

Edm control board
- Size
- 240 × 100 mm
- Copper layers
- 4
- Thickness
- 1.6 mm
- Parts
- 71
- Nets
- 71
- Pads
- 263
- Tracks, vias
- 501, 61
- Pours
- 8
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 29 Jan 2018
- Updated
- 4 Nov 2020
Overview
Edm control board is an open-source printed circuit board by strombom, from the strombom/EDM repository on GitHub. It is a 4-layer board of 240 × 100 mm with 71 parts on 71 nets, routed with 501 tracks and 61 vias.
It is built around the R-78E3.3-1.0, ZXGD3009E6TA and BSS214NW-TP, with the DMN3404L-7-ES among its other parts. Its parts include 22 capacitors, 9 resistors, 6 connectors, 5 ICs and 5 transistors. It belongs with the STM32 boards of this library.
Main components
4R-78E3.3-1.0
SIP,11.6x7.5mm-40℃~+85℃ 1 10.2mm 11.6mm 1A 2200uF 3.3V 300uA 50mVp-p 6V~36V 7.5mm 850kHz 90% Short Circuit Protection、Automatic fault recovery Step-down type ±3% SIP,11.6x7.5mm DC-DC Power Modules ROHSYLPTECDC-DC Power ModulesZXGD3009E6TA
SOT-26-55℃~+150℃ 1 20nA 210ns 240ns 2A 2A 40V Interleaved conduction protection Low Side MOSFET SOT-26 Gate Drivers ROHSDiodes IncorporatedGate DriversBSS214NW-TP
SOT-323MOSFETsTECH PUBLICDMN3404L-7-ES
SOT-23-55℃~+150℃ 1 N-channel 1.4W 1.5V 17mΩ@10V 255pF 30V 35pF 45pF 6.2A 9.8nC@10V N-Channel SOT-23 MOSFETs ROHSElecSuperMOSFETs
README
README.mdEDM
Control board
- Stepper motor output.
- Power board control output.
- Buttons for stepper motor up/down and EDM start/stop.
- LCD display 4x20 characters for status.
- Potentiometers for setting voltage, current (not implemented in this revision), on-time and off-time.
Power board
- Voltage source, low current for initiating spark. Selectable 250 V, 200 V, 150 V or 100 V. Status comparator checks if voltage is above 70 V.
- Current source, for providing current to the spark. Current limited to 10 A, adjustable with potentiometer. Spark output, has two power transistors to enable the control board to control the voltage and current outputs independently. Has two comparators (5 V and 30 V) to give feedback to the control board, monitoring if a spark has started (breakdown) and to check for short circuit.
Design files
Parts
71| Qty | Value | Footprint | References |
|---|---|---|---|
| 12 | Mounting_Hole_PAD | MountingHole:MountingHole_5mm_Pad | MK501, MK502, MK503, MK504, MK505, MK506, MK507, MK508, MK509, MK510, MK511, MK512 |
| 10 | 100n | Capacitor_SMD:C_0805_2012Metric | C201, C202, C203, C204, C205, C206, C209, C303, C304, C602 |
| 6 | 27k | Resistor_SMD:R_0805_2012Metric | R201, R202, R203, R204, R206, R207 |
| 4 | BSS214NW | Package_TO_SOT_SMD:SOT-323_SC-70 | Q201, Q202, Q203, Q204 |
| 4 | Conn_01x02 | TerminalBlock:TerminalBlock_bornier-2_P5.08mm | J402, J403, J404, J406 |
| 4 | POT | Potentiometer_THT:Potentiometer_TT_P0915N | RV501, RV502, RV503, RV504 |
| 4 | SW_Push | Button_Switch_THT:SW_PUSH_CK_PVA1 | SW501, SW502, SW503, SW504 |
| 3 | 10u | Capacitor_SMD:CP_Elec_6.3x5.3 | C305, C306, C601 |
| 2 | 12p | Capacitor_SMD:C_0805_2012Metric | C208, C210 |
| 2 | 2u2 | Capacitor_SMD:C_0805_2012Metric | C211, C212 |
| 2 | 330n | Capacitor_SMD:C_0805_2012Metric | C301, C302 |
| 1 | 1800p | Capacitor_SMD:C_2220_5650Metric | C401 |
| 1 | 1M | Resistor_SMD:R_1206_3216Metric | R401 |
| 1 | 1n | Capacitor_SMD:C_0805_2012Metric | C603 |
| 1 | 1u | Capacitor_SMD:C_0805_2012Metric | C207 |
| 1 | 20R | Resistor_SMD:R_0805_2012Metric | R205 |
| 1 | 20k | Potentiometer_SMD:Potentiometer_Bourns_3214J_Horizontal | RV201 |
| 1 | 25M | Crystal:Crystal_SMD_5032-2Pin_5.0x3.2mm | Y201 |
| 1 | 4R99 | Resistor_SMD:R_0805_2012Metric | R601 |
| 1 | CDBA140-G | Diode_SMD:D_SMA | D601 |
| 1 | Conn_01x06 | Connector_PinHeader_2.54mm:PinHeader_1x06_P2.54mm_Vertical | J405 |
| 1 | Conn_02x08_Odd_Even | Connector_PinHeader_2.54mm:PinHeader_2x08_P2.54mm_Vertical | J401 |
| 1 | DMN3404L-7 | Package_TO_SOT_SMD:SOT-23 | Q601 |
| 1 | L78L05_SO8 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U303 |
| 1 | NHD-0420H1Z | Display:NHD-0420H1Z | U501 |
| 1 | Net-Tie_2 | NetTie:NetTie-2_SMD_Pad2.0mm | NT301 |
| 1 | R-78E3.3-1.0 | Converter_DCDC:Converter_DCDC_RECOM_R-78E-0.5_THT | U302 |
| 1 | STM32F722RETx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U301 |
| 1 | ZXGD3009E6 | Package_TO_SOT_SMD:SOT-23-6 | U601 |
More from strombom/EDM
1- 4 layers240 × 80 mm

Similar boards
- 2 layers58.4 × 66.7 mm

PWM10
Duckle29/PWM-Solar-Charge-Controller
A PWM Solar Charge controller based on Julian Lietts PWM5
55 parts9MIT - 2 layers57.7 × 50 mm

KiCAD Board
XasWorks/dragon-home
A rework of our old SmartHome project, this time done cleanly and neatly~
47 parts8GPL-3.0 - 2 layers77 × 73.5 mm

EChook Nano
eChook/eChook-Nano-PCB
Designspark Schematics and PCB files, and PCB Gerber Files
141 parts2 - 4 layers263 × 139.8 mm

LV Board Mk2
Lafayette-Motorsports/LVBoards
LV Board repository for Motorsports created 09.02.2025
184 parts1 - 4 layers220 × 130 mm

Gantry controller prototype DUE
kitspace-forks/growbox-open-motion-mobo
A general purpose open source Arduino DUE based motion controller designed to run the Synthetos G2 motion control fimware
138 parts - 4 layers60 × 40 mm

Usb c pd supply
nmatic00/kicad-usbc-pd-psu
Based on Robert Feranec design. USB-C PD power supply based on CH224K sink controller
43 parts - 4 layers48 × 47.7 mm

- 2 layers150 × 70 mm

Questions
How big is the Edm control board PCB?
It measures 240 × 100 mm and has 4 copper layers, 1.6 mm thick.
What parts does the Edm control board use?
71 parts, built around the R-78E3.3-1.0, ZXGD3009E6TA, BSS214NW-TP and DMN3404L-7-ES. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Edm control board KiCad files?
From the strombom/EDM repository on GitHub, at the commit this page was made from: the board is hardware/edm_control_board/cad/edm_control_board.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the Edm control board design in my own project?
Its repository states no licence, so its author keeps all rights: ask strombom before reusing the design.