Skip to the content
4 layers85.8 × 69.8 mmInternetDrone, the printed circuit board in 3D

A fully autonomous drone for precise indoor navigation and worldwide remote control.

Size
85.8 × 69.8 mm
Copper layers
4
Thickness
1.6 mm
Parts
47
Nets
74
Pads
195
Tracks, vias
786, 117
Pours
2
Routed
Yes
KiCad
KiCad 10.0 (file 20260206)
Created
22 May 2026
Updated
29 Oct 2026

Overview

InternetDrone is an open-source printed circuit board by Stefanos0710, from the Stefanos0710/Odonata repository on GitHub, published under the MIT licence. It is a 4-layer board of 85.8 × 69.8 mm with 47 parts on 74 nets, routed with 786 tracks and 117 vias.

It is built around the MP1584EN, ADS1115 and AOD4185, with the B340 among its other parts. Its parts include 16 resistors, 11 connectors, 9 capacitors, 3 ICs and 1 diode. It belongs with the robots and motor control boards of this library.

Main components

4

README

README.md

Odonata

Odonata is an autonomous indoor drone controlled over a local network. I had the idea for the project, after I once bought a drone that broke after just two days because I struggled to control it manually. Sothat it doesn´t crash again, I decided to build a new, autonomous drone and named it Odonata, after the Latin word for dragonfly.

The drone weighs about 300g and uses a 3S 11.1V 850mAh battery, giving it a flight time of roughly 5 minutes. With around 1100g of thrust, it achieves a 3:1 thrust-to-weight ratio, which allows precise flights. For navigation, it has 4 ToF (Time-of-Flight) sensors to track its position in the room, and it can perform controlled autonomous landings using a camera that detects AprilTags on the landing station. The landing station is designed with self-centering sticks, sothat even with a positioning error of about 1cm, the drone can still lands safely.

Odonata runs on a Raspberry Pi Zero 2W and a DarwinFPV flight controller, connected together via a custom PCB. With this setup the Pi can send and receive data using MAVLink commands (such as starting the motors, pitching, etc.). The project is split into two parts: the drone itself and a local server. The server hosts a web-based cockpit where you can monitor the drone, test the motors, and start-stop flights. Because it works locally, you can easily host the server on your laptop, PC, or a separate Raspberry Pi.

First Flight

The first version of Odonata in flight:

Odonata first flight

Watch in full quality on YouTube

Zine Poster

Here is the Zine poster of my project Odonata:

Odonata Zine

Website/Cockpit

Here you can see the user interface of the cockpit where you can monitor the drone and send commands: Cockpit

CAD Model

The CAD design of Odonata is split into several parts, like the arms, the walls, the base, the cover, and the propguards. Everything is attached using M2 screws and heat inserts, or slide-ins and snap-fits. The .step, .stl and f3d/f3z files can be found at the /CAD directory. Here are some nice renders of the assembled drone:

(All parts were modeled and rendered in Autodesk Fusion 360)

Landing Station Assembly

Click here to view more renders

Cool Drone Render Close Up Render Drone on Floor

PCB

This custom PCB is designed in KiCad and makes the flawless communication between the Flight Controller and the Raspberry Pi Zero 2W possible, and also connects the servo, the ToF sensors and camera to a working system. It uses a 4-layer design for the optimal routing and to ensure no noise on the power lines.

Schematics

Schematics

PCB-Layers

The PCB uses 4 layers: 1. TOP-Signal layer 2. GND layer 3. Power layer 4. Signal and GND layer

1. Layer (Top-Signal)

1. Layer

2. Layer (GND)

2. Layer

3. Layer (Power)

3. Layer

4. Layer (Signal/GND)

4. Layer

PCB 3D-Rendering
FrontBack
FrontBack
JLCPCB Order

JLCPCB

How to build Odonata (Step-by-Step)

If you want to rebuild this drone without any modifications, you can follow these next steps. If you want to modify the drone, you can follow along the guide, you just have to adjust it to your changes:

1. Getting the parts

  1. Download the whole repository on your computer by running these commands in your terminal to download the firmware, CAD, and PCB:

    bash
    git clone https://github.com/Stefanos0710/Odonata.git
    cd Odonata

    After that, you will have cloned the entire project onto your computer.

  2. Next, you have to print out the 3D parts, and therefore you have 2 options, based on whether you have a 3D printer or not:

    1. If you have a 3D printer: upload the stl files from /CAD/f3d_stl into your slicer software. You have to print every file separately. So for the propguards you need 4, the motor arms you need 4, the base you need 1, the wall you need 1, the cover you need 1, and you need the camera holder. For the landing station, you need the catcher and the AprilTag holder.
    2. If you don't have a 3D printer, you can use a company like PCBWay, JLCPCB, or any other 3D printing service. There you have to upload the exact same files I mentioned previously and order them.
    3. Overall for the filament, if you can choose which one you can use, I would assume to use TPU for the propguards and print the rest with PETG for the best stability. For the color, if you like the style of the drone, it should be light/lime green and purple/blue.
  3. Next, you should order the PCB. Therefore you need the gerber files which you find at PCB/gerbers as a gerbers.zip file. This file you can upload on a service like PCBWay, JLCPCB, or any other of your choice. Make sure to select 4 layers, and for the color it doesn't matter, but in this case I used the typical green one. Otherwise, I use the default options, so FR-4 as material.

  4. Next, we need to get/buy the rest of the parts. A list with all parts you can find further down in the README, or in the BOM.csv file. There is the cost of the parts, the links, name, and description. INFO: the shipping cost is calculated for ordering to Bavaria, Germany, so it might change for you. But the rough price without shipping is 222,71€.

2. Setting up the Raspberry Pi Zero 2 W

After you got all the parts, we can start building the drone. And therefore we will start setting up the Raspberry Pi Zero 2 W:

  1. Firstly, you need to download the Raspberry Pi Imager software on your computer, so that you can install the OS on the Raspberry Pi. First open this site https://www.raspberrypi.com/software/ and download it for your OS (Windows/macOS/Linux).

  2. After downloading, you need to attach a micro SD card with at least 16GB to the computer, so that you can flash the OS and attach it later into the Raspberry Pi.

  3. Then you choose the Raspberry Pi OS Lite, without the desktop, so that we don't waste resource power on that.

  4. During that procedure, you will need to add the name (I assume to use "odonata" as the name), the WLAN (this must match the WLAN that you are connected to with your computer and later your server), and very important is to activate SSH, and lastly, you have to add a username and a password.

  5. Then you detach the micro SD from your computer and attach it into the Raspberry Pi and connect it with a USB for power.

  6. After waiting for about 5 min so that the OS can boot, you can type (for Windows):

    bash
    ssh yourusername@odonata.local

    And so you should be connected to the Raspberry Pi.

  7. Now we update the system by typing in:

    bash
    sudo apt update
    sudo apt upgrade -y
  8. After that, type in sudo raspi-config and activate the camera, the SPI, and the I2C.

  9. After that, we have to install Python and Git. It's mostly already installed, but to update it's good:

    bash
    sudo apt install python3 python3-pip python3-venv git -y
    python3 --version
    pip3 --version
    git --version

    If you see no error, then everything is fine and installed.

  10. And lastly, you have to copy the drone folder from firmware to the Raspberry Pi, and you can do it with this:

bash
git clone --depth 1 https://github.com/Stefanos0710/Odonata.git temp_repo
mv temp_repo/firmware/drone ./drone
mv temp_repo/firmware/requirements.txt ./
rm -rf temp_repo

cd drone
pip install -r requirements.txt
  1. Then, to activate the communication with the FC, you have to also add in sudo raspi-config under Interface Options -> Serial Port:
    • Login shell over serial? → No
    • Enable serial hardware? → Yes And then reboot.

3. Flight Controller Configuration

  1. After we set up the Pi, we have to configure the FC (Flight Controller) so that we can use MAVLink on it. Therefore, you have to firstly install Mission Planner and then connect the FC with a USB cable to the PC.
  2. Then you have to choose the COM port and the baud number that should be 115200, and then click Connect.
  3. Then open the menu under Initial Setup and then Install Firmware, then select ArduCopter.
  4. During that process, the firmware is installed and the FC is rebooted multiple times.
  5. After that, you should read a text called ArduCopter Vx.x.x, and if Mission Planner connected again, then all is perfect.
  6. Then we have to configure the parameters in Mission Planner. Therefore you go under Config to Full Parameter List and fill this out:
    • SERIAL2_PROTOCOL = 2
    • SERIAL2_BAUD = 115
  7. This activates MAVLink2 which allows the communication with the Pi, and the baud number is the standard for drones with MAVLink. And after clicking on "Write Params", you are finished and you set everything up.

4. PCB Soldering

  1. Now you have to solder all the SMD parts on the drone PCB. There isn't really a step-by-step for this, try to orientate yourself from the PCB renders, the schematics, and PCB layer 1.

5. Drone Assembly

After everything is soldered, you need to assemble the hardware parts:

  1. Place the PCB on the base that was 3D printed, then add the placeholders (spacers) from the FC. Put the FC on it and screw it on with the M2 12mm screws.

  2. Attach the Raspberry Pi to the male pins.

  3. For the power, I firstly recommend to use a laboratory power supply so that you don't destroy your battery if something is wrong.

  4. To connect everything, you need to connect the TX and RX cables from J2 with the RX and TX cables from the FC, and the rest of the parts are pretty easy to connect. Orientate yourself here again from the schematics and the PCB design.

  5. Lastly run that command to install mavproxy:

    bash
    python3 mavproxy.py --master=/dev/serial0 --baudrate 115200 --aircraft MyCopter
  6. And now we can attach the rest of the parts. Firstly, you have to insert the heat inserts with a soldering iron into the parts. Therefore you have to add them to the motor arms and the walls.

  7. After that, you have to place the arms in the holding parts from the base and screw them with the M2 6mm screws into the base.

  8. Next, you place the prop guards at the place where the motors go and screw them again with 6mm screws.

  9. And now you have to lengthen the cables from the motors and place them in the cable canal from the arm into the inside of the drone, and solder the cables onto the FC pads for the motors.

  10. Next, you have to attach the camera holder to the servo and also place the camera module into it, and place it in the front of the base. Make sure that the camera cable goes above the servo, connect the servo cable with its JST-GH cable, and attach it onto the PCB.

  11. Next, solder the JST-GH cables to the ToF sensors and also add them to the PCB.

  12. After all of this, you can place the walls and screw them on the base.

  13. Next, place all the ToF sensors in their positions and make sure to press them in so that they hold their place. And now you are ready for the first test.

6. Server Setup

  1. Go to your server computer or on the computer where you are currently working, and run these commands:

    bash
    git clone --depth 1 https://github.com/Stefanos0710/Odonata.git temp_repo
    mv temp_repo/firmware/server ./server
    mv temp_repo/firmware/requirements.txt ./
    rm -rf temp_repo
    
    cd server
    pip install -r requirements.txt
    
    fastapi dev
  2. Then open 127.0.0.1:8000 and you will see the drone cockpit.

  3. There you have to firstly add the IP by pressing "Connect Drone" or wait until the IP shows up, and connect the drone.

  4. Then start the drone and test every motor and every component independently. If everything works fine, you are ready for the final step!

7. Final Touches

  1. Now you can attach the propellers to the drone, and make sure they sit very tight.
  2. After also attaching the battery and the on/off switch at the cover, you now have to print this paper out (april_tag_print.pdf) and add it to the AprilTag holder.
  3. Attach the AprilTag holder under the catcher, place the drone on the catcher, and let it start via the cockpit by pressing "Start Flight" and see the magic happen.

BOM (Bill of Materials)

Here is a list of components and parts I used for this project: (You can also find the csv file here)

NameDescriptionLinkUnit Cost (€)QuantityPrice (€)Shipping CostTotal
C110uF 0805 CapacitorLCSC0,0310,000,3418,91
C2, C3150pF 0603 CapacitorLCSC0,0150,000,4118,91
C422uF 0805 CapacitorLCSC0,00100,000,4818,91
C51000uF Electrolytic Capacitors 10mm*5mmLCSC0,151,000,1518,91
C7100nF 0603 CapacitorLCSC0,031,000,0318,91
C8100uF Electrolytic 6.3mm 11mm CapacitorLCSC0,055,000,2618,91
C9100nF 0805 CapacitorLCSC0,0150,000,3518,91
D2Schottky-Diode 3ALCSC0,0610,000,6318,91
FB1Ferrite Bead 0805 300 ohm 2ALCSC0,0250,000,7818,91
J1female connector with piLCSC0,205,000,9918,91
J2JST-GH 1x03-1MP_P1.25mm_VerticalLCSC0,671,000,6718,91
J3JST-XH 1x04LCSC0,0510,000,4818,91
J4JST-GH 1x03-1MP_P1.25mm_HorizontalLCSC0,125,000,6018,91
J5, J6XT30-Female VerticalLCSC0,215,001,0618,91
J7JST-GH 1x02 verticalLCSC0,185,000,9118,91
J8, J9, J10JST-GH 1x05 VerticalLCSC0,305,001,5118,91
J11JST-GH 1x05 HorizontalLCSC0,185,000,8918,91
L1Inductor 7.3x7.3_4.5H 15uH 5ALCSC0,881,000,8818,91
Q1AOD4185 40V 40ALCSC0,165,000,8118,91
R1, R11, R13, R15SMD Resistor 0603 10k 0.5% toleranceLCSC0,00100,000,1018,91
R2, R30603 4.7k 1%LCSC0,00100,000,1418,91
R4, R6, R7, R100603 100k 1%LCSC0,00100,000,1118,91
R50603 24.9k 0,1 toleranceLCSC0,095,000,4718,91
R80603 40.2k 1%LCSC0,00100,000,1318,91
R90603 210k 1%LCSC0,0183200,3718,91
R120603 33kLCSC0,095,000,4418,91
R140603 5.6k 0.1%LCSC0,075,000,3618,91
R160603 3.3k 1%LCSC0,00111000,1118,91
U1TCA9548APWRLCSC0,571,000,5718,91
U2mp1584enLiD/Aliexpress4,581,004,580
U3ADS1115LCSC1,431,001,4318,91
JST GH 1.25 SetJST GH1.25 GH 1.25mm Connector Kit 2/3/4/5/6/7/8/9/10Pin Housing Pre-Crimped Cable WireAliexpress17,791,0017,790
XT30-F cableXT30U Amass 1PCS Male Female Connector Plug With 16 AWGAliexpress4,731,004,730
Cable2 Pins Super Soft Black Red Silicone CableAliexpress1,081,001,080
Flight ControllerDarwinFPV F411 15A AIO (FC+ESC+RX) ELRSRotorama53,391,0053,390
MotorsHappymodel EX1204 5000KV 3S 3" MotorAliexpress37,791,0037,790
PropsGemfan Hurricane 3016 3inch Toothpick 3X1.6X3 3-Blade PC PropellerAliexpress7,891,007,890
BatteryTattu 3S Lipo Battery 850 mAh 11.1 V 150C 3S1PAmazon23,991,0023,990
Raspberry Pi Zero 2 WRaspberry Pi Zero 2 WPi-Shop19,531,0019,5313,5
Camera130° 8MP CameraAliexpress8,111,008,110
ToF SensorVL53L0X Time-of-Flight (ToF) Laser Ranging Sensor Breakout 940nmAliexpress3,244,0012,960
PCB4 Layer custom PCBJLCPCB5,991,005,997,81
Raspberry Pi Pin HeaderBOOMELE(Boom Precision Elec) 2.54-2*20PLCSC0,265,001,2918,91
Screw 6mm50pcs Black 304 Stainless Steel Cross Phillips CM M2 6mmAliexpress2,001,002,000
Screw 12mm50pcs Black 304 Stainless Steel Cross Phillips CM M2 12mmAliexpress2,521,002,520
Heat insert50pcs M2 2mmAliexpress2,661,002,660
SwitchKCD1 15*21mm 2 Pin Boat SwitchAliexpress0,385,001,9018,91
ServoSG90Aliexpress1,911,001,910
Sum Costs224,6240,22264,84

Huge thanks to Fallout from Hack Club for inspiring me to build this project and for financing it!

Parts

47
QtyValueFootprintReferences
4100kResistor_SMD:R_0603_1608MetricR4, R6, R7, R10
310kResistor_SMD:R_0603_1608MetricR11, R13, R15
3Conn_01x05Connector_JST:JST_GH_BM05B-GHS-TBT_1x05-1MP_P1.25mm_VerticalJ8, J9, J10
24.7kΩResistor_SMD:R_0603_1608MetricR2, R3
11000uFCapacitor_THT:CP_Radial_D10.0mm_P5.00mmC5
1100nFCapacitor_SMD:C_0805_2012MetricC9
1100nFCapacitor_SMD:C_0603_1608MetricC7
1100uFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC8
110kΩResistor_SMD:R_0603_1608MetricR1
110uFCapacitor_SMD:C_0805_2012MetricC1
1150nFCapacitor_SMD:C_0603_1608MetricC3
1150pFCapacitor_SMD:C_0603_1608MetricC2
115uHInductor_SMD:L_7.3x7.3_H4.5L1
1210kResistor_SMD:R_0603_1608MetricR9
1220uFCapacitor_THT:CP_Radial_D6.3mm_P2.50mmC8
122uFCapacitor_SMD:C_0805_2012MetricC4
124.9kResistor_SMD:R_0603_1608MetricR5
13.3kResistor_SMD:R_0603_1608MetricR16
133kResistor_SMD:R_0603_1608MetricR12
140.2kResistor_SMD:R_0603_1608MetricR8
15.6kResistor_SMD:R_0603_1608MetricR14
1ADS1115Package_SO:TSSOP-10_3x3mm_P0.5mmU3
1AOD4185Package_TO_SOT_SMD:TO-252-2Q1
1B340Diode_SMD:D_SMCD2
1Battery-StatusConnector_JST:JST_XH_B4B-XH-A_1x04_P2.50mm_VerticalJ3
1Conn_01x02Connector_JST:JST_GH_BM02B-GHS-TBT_1x02-1MP_P1.25mm_VerticalJ7
1Conn_01x03Connector_JST:JST_GH_SM03B-GHS-TB_1x03-1MP_P1.25mm_HorizontalJ4
1Conn_01x03Connector_JST:JST_GH_BM03B-GHS-TBT_1x03-1MP_P1.25mm_VerticalJ2
1Conn_01x05Connector_JST:JST_GH_SM05B-GHS-TB_1x05-1MP_P1.25mm_HorizontalJ11
1Conn_02x20_Odd_EvenConnector_PinHeader_2.54mm:PinHeader_2x20_P2.54mm_VerticalJ1
1FerriteBead_SmallInductor_SMD:L_0805_2012MetricFB1
1LOGOINTERNETDRONE_flag:soupeG***
1LOGOINTERNETDRONE_flag:hc_flagG***
1LOGOINTERNETDRONE_flag:skateG***
1LOGOINTERNETDRONE_flag:falloutG***
1MP1584Package_SO:SOIC-8_3.9x4.9mm_P1.27mmU2
1TCA9548APWRPackage_SO:TSSOP-24_4.4x7.8mm_P0.65mmU1
1XT30Connector_AMASS:AMASS_XT30U-M_1x02_P5.0mm_VerticalJ6
1XT30 - BatteryConnector_AMASS:AMASS_XT30U-M_1x02_P5.0mm_VerticalJ5

Similar boards

  • 2 layers100 × 46.3 mmMicro generator test machine, the printed circuit board in 3D

    Micro generator test machine

    ujkhm/micro-generator-test-machine

    ESP32 MPPT for micro-generator output measurement.

    51 partsMIT
  • 4 layers100 × 100 mmPi TX 35W PA, the printed circuit board in 3D

    Pi TX 35W PA

    M0LTE/pi-transceiver

    An attempt to build a complete ham radio transceiver around a Raspberry Pi

    161 parts15
  • 4 layers65.9 × 52.7 mmMotor shield, the printed circuit board in 3D

    Motor shield

    DCC-EX/EX-Hardware

    Open Source hardware projects developed by the DCC-EX Team

    123 parts7CERN-OHL-W-2.0
  • 2 layers101.6 × 76.2 mmCameraBoard, the printed circuit board in 3D

    CameraBoard

    psas/lv3.1-avionics

    Avionics for the LV3.1 rocket

    68 parts5GPL-3.0
  • 2 layers216 × 164 mmMPPT Li Ion CN3791 charger board panel, the printed circuit board in 3D

    MPPT Li Ion CN3791 charger board panel

    SolderedElectronics/MPPT-Li-Ion-CN3791-charger-board-hardware-design

    Hardware design, BOM, gerbers and 3D files for MPPT-Li-Ion-CN3791-charger-board designed by Soldered Electronics.

    988 parts5
  • 4 layers100 × 30 mmRevo main, the printed circuit board in 3D

    Revo main

    ratmuds/revo

    a "cheap" 6 DoF robot arm intentionally pushing the limits of low quality hobby servos

    58 parts2MIT
  • 4 layers81 × 90.3 mmMildly Overkill, the printed circuit board in 3D

    Mildly Overkill

    hackepeter101/Mildly-Overkill

    todo.md was written entirely by AI. It's the list of everything it found. I read the suggestions, double-check them, and then fix them myself in KiCad, usually while muttering.

    138 parts1
  • 4 layers100 × 50 mmDcesc ga25, the printed circuit board in 3D

    Dcesc ga25

    baden/roboarm

    Так, це роборука.

    219 parts

Questions

How big is the InternetDrone PCB?

It measures 85.8 × 69.8 mm and has 4 copper layers, 1.6 mm thick.

What parts does the InternetDrone use?

47 parts, built around the MP1584EN, ADS1115, AOD4185 and B340. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the InternetDrone KiCad files?

From the Stefanos0710/Odonata repository on GitHub, at the commit this page was made from: the board is PCB/InternetDrone.kicad_pcb and its schematic PCB/InternetDrone.kicad_sch. PCBKit opens the board in the browser, with nothing to install.

Can I use the InternetDrone design in my own project?

Its repository publishes it under the MIT licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).