

LoRA Dev
RA-01 LoRa
- Size
- 71.5 × 83.7 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 67
- Nets
- 116
- Pads
- 322
- Tracks, vias
- 897, 334
- Pours
- 20
- Routed
- Yes
- KiCad
- KiCad 5 (file 20171130)
- Created
- 5 Mar 2020
- Updated
- 1 Jul 2020
Overview
LoRA Dev is an open-source printed circuit board by SpyrosCpt, from the SpyrosCpt/RA-01-LoRa repository on GitHub. It is a 2-layer board of 71.5 × 83.7 mm with 67 parts on 116 nets, routed with 897 tracks and 334 vias.
It is built around the CP2102N-A01-GQFN28R. Its parts include 19 capacitors, 18 resistors, 8 ICs, 8 diodes and 6 connectors. It belongs with the radio and wireless boards and the STM32 boards of this library.
Main components
1README
README.mdRA-01-LoRa Dev Board
Features
- Max 15V DC input
- 5V DC USB input
- CP2102 USB interface
- STM32F030RCT6
- 0.96" 128 x 32 OLED
- RA-01 LoRA Module
- LM35 Temperature Sensor
- AT93C46 EEPROM
- 4 Way DIP Switch
- 4 Push Buttons
- STM32 programming by SWD
Firmware Example Provided
- Press Push Button 1 to Send LoRA Packet, you can change the data to send by editing TestLoraTransmit("packet to send")
- When not transmitting LoRA radio is in Receiver mode and will display any messages receievd
- Temperature Monitoring of LM35 will be displayed on OLED
Hardware Version 1.1

Firmware Change Log
- Changed frequency down from 915Mhz to 433MHz
- Oled working
- LoRa working
- EEPROM working
- Temp Sensor
Harware Change Log
- Removed USB protection IC
- Swapped TX and RX lines
- Grounded pin 16 + 17 on OLED connector
- Moved LM34 Vcc from 3.3V to 5V
Parts
67| Qty | Value | Footprint | References |
|---|---|---|---|
| 7 | C_100nF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C1, C2, C3, C4, C5, C6, C17 |
| 7 | R_330R | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R1, R2, R3, R4, R10, R12, R18 |
| 6 | D_LED_R | LED_SMD:LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D1, D2, D3, D4, D7, D8 |
| 5 | C_1uF | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C12, C13, C14, C15, C16 |
| 5 | R_10K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R5, R6, R7, R8, R13 |
| 4 | SW_Push | Button_Switch_SMD:SW_SPST_PTS645 | SW2, SW3, SW4, SW5 |
| 2 | C_10uF/16V | Capacitor_Tantalum_SMD:CP_EIA-6032-28_Kemet-C_Pad2.25x2.35mm_HandSolder | C10, C11 |
| 2 | C_2U2F2 | Capacitor_SMD:C_0805_2012Metric_Pad1.15x1.40mm_HandSolder | C18, C19 |
| 1 | 0.96_OLED_128X64 | LoRA:0.96_OLED | U5 |
| 1 | Ai-Thinker-Ra-01 | RF_Module:Ai-Thinker-Ra-01-LoRa | U6 |
| 1 | Barrel_Jack_Switch | Connector_BarrelJack:BarrelJack_Horizontal | J2 |
| 1 | CONN_CURRENT_MEASURE | Connector_PinHeader_2.54mm:PinHeader_2x01_P2.54mm_Vertical | J3 |
| 1 | CONN_PGM | Connector_PinHeader_2.54mm:PinHeader_2x04_P2.54mm_Vertical | J1 |
| 1 | CP2102N-A01-GQFN28 | Package_DFN_QFN:QFN-28-1EP_5x5mm_P0.5mm_EP3.35x3.35mm | U8 |
| 1 | C_1000uF/10V | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C9 |
| 1 | C_330uF/35V | Capacitor_THT:CP_Radial_D10.0mm_P5.00mm | C7 |
| 1 | C_470pF | Capacitor_SMD:C_0603_1608Metric_Pad1.05x0.95mm_HandSolder | C8 |
| 1 | Conn_01x02_Male | Connector_PinHeader_2.54mm:PinHeader_1x02_P2.54mm_Vertical | J5 |
| 1 | Conn_Coaxial | Connector_Coaxial:SMA_Amphenol_132134_Vertical | J6 |
| 1 | D_P6SMBJ26 | Diode_SMD:D_SMB | D5 |
| 1 | D_SK14 | Diode_SMD:D_SMB | D6 |
| 1 | F_SMD2920P150TSA | Fuse:Fuse_2920_7451Metric_Pad2.10x5.45mm_HandSolder | F1 |
| 1 | Fuse_Small | Capacitor_SMD:C_0805_2012Metric | F2 |
| 1 | IC_AT93C46 | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | IC_LM1117MPX-ADJ | Package_TO_SOT_SMD:SOT-223-3_TabPin2 | U4 |
| 1 | IC_MC34063AD | Package_SO:SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | IC_STM32F030RCTx | Package_QFP:LQFP-64_10x10mm_P0.5mm | U1 |
| 1 | LM35-LP | Package_TO_SOT_THT:TO-92 | U9 |
| 1 | L_220UH | Inductor_SMD:L_12x12mm_H8mm | L1 |
| 1 | R_12K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R14 |
| 1 | R_1K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R11 |
| 1 | R_1K5 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R15 |
| 1 | R_2K7 | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R9 |
| 1 | R_390K | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R16 |
| 1 | R_470R | Resistor_SMD:R_0603_1608Metric_Pad1.05x0.95mm_HandSolder | R17 |
| 1 | SW_4_PIN_DIP | Button_Switch_THT:SW_DIP_SPSTx04_Slide_9.78x12.34mm_W7.62mm_P2.54mm | SW1 |
| 1 | USB_B_Mini | Connector_USB:USB_Mini-B_Lumberg_2486_01_Horizontal | J7 |
Similar boards
- 2 layers100 × 57 mm

- 2 layers39.6 × 99.1 mm

ESP32-Eurorack Audio
ctag-fh-kiel/ctag-tbd
CTAG TBD >>to be determined<< an extendible open source Eurorack sound module
128 parts260 - 2 layers50 × 30 mm

- 2 layers53.5 × 101.8 mm

Sony scopeman
lucysrausch/sony-scopeman
Hardware Design files of a replacement mainboard for the Sony Watchman FD-10. This turns it into a bluetooth and WiFi-enabled vector display.
135 parts69 - 2 layers38.5 × 43 mm

Stepper monitor
zapta/ble_stepper_motor_analyzer
A low cost stepper motor analyzer that uses wireless BLE link to display the data in real time on a Windows/Mac/Linux PC.
58 parts58 - 2 layers65 × 30 mm

Epaper
TDA-2030/E-ink-screen
An assistant to help you view text and picture calendars
56 parts33Apache-2.0 - 4 layers536.5 × 385.7 mm

- 2 layers123 × 87.5 mm

FastLOGIC
Neumi/fastLOGIC
An affordable Arduino-based board designed for straightforward (industrial) logic control, ideal for building small-scale automation and control solutions.
180 parts23MIT
Questions
How big is the LoRA Dev PCB?
It measures 71.5 × 83.7 mm and has 2 copper layers, 1.6 mm thick.
What parts does the LoRA Dev use?
67 parts, built around the CP2102N-A01-GQFN28R. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the LoRA Dev KiCad files?
From the SpyrosCpt/RA-01-LoRa repository on GitHub, at the commit this page was made from: the board is Hardware/LoRA_Dev.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.
Can I use the LoRA Dev design in my own project?
Its repository states no licence, so its author keeps all rights: ask SpyrosCpt before reusing the design.