Skip to the content
2 layers26 × 44.5 mmReceiverBoard, the printed circuit board in 3D

The goal of this project is to develop the cheapest and simplest to construct NMR.

Size
26 × 44.5 mm
Copper layers
2
Thickness
1.6 mm
Parts
12
Nets
6
Pads
29
Tracks, vias
0, 0
Pours
1
Routed
Not yet
KiCad
KiCad 3
Created
16 Apr 2014
Updated
18 May 2014

Overview

ReceiverBoard is an open-source printed circuit board by spencerwhyte, from the spencerwhyte/SimpleNMR repository on GitHub. It is a 2-layer board of 26 × 44.5 mm with 12 parts on 6 nets.

Its parts include 4 resistors, 2 connectors and 1 IC.

README

README.md

Simple NMR

This is my first adventure into NMR and I want to keep everything as simple as possible for the first design.

The process goes a little something like this.

  1. Apply a pre-polarizing pulse to the sample.
  2. Transmit 90 degree pulse
  3. Listen to the FID

Transmit/Receive Board

There is a board which controls the polarization, transmission amplification, and receiver amplification. kicad designs for this board can be found in the RelayBoard folder.

To elaborate on the simple process described above, here is what actually happens.

  1. Apply a pre-polarizing pulse to the sample

    • Configure the relays to disable transmit and receive functionality (To protect the electronics)
    • Turn on the polarization coil
    • Wait some fixed period of time
    • Turn off the polarization coil
  2. Transmit 90 degree pulse

    • Configure the relays to allow transmission
    • Tell GNURadio to output a sine wave at the larmour frequency to the sound card/audio interface
    • Wait 90 degrees worth of time
    • Tell GNURadio to stop the output
    • Configure the relays to disable transmission
  3. Listen to the FID

    • Configure the relays to enable receiving
    • Tell GNURadio to record from line-in
    • Apply a Peak hold FFT to the input signal to see what we received

Amplification Board

There is another board which amplifies the transmitted and received signals. kicad designs for the amplifier board can be found in the AmplifierBoard folder.

Parts

12
QtyValueFootprintReferences
4P***1pin1PIN, 1PIN, 1PIN, 1PIN
13.3MR3R1
13.3kR3R4
155R3R2
169kR3R3
1CONN_2PinHeader2P1
1HEADPHONEJACKHeadphoneJackJ1
1LT1115SWDIP4U1
1POTPOT_P160KNRV1

More from spencerwhyte/SimpleNMR

2
  • 2 layers50 × 50 mm.kicad_pcb, the printed circuit board in 3D

    .kicad_pcb

    spencerwhyte/SimpleNMR

    The goal of this project is to develop the cheapest and simplest to construct NMR.

    21 parts4
  • 2 layers50 × 50 mmTransmitter, the printed circuit board in 3D

    Transmitter

    spencerwhyte/SimpleNMR

    The goal of this project is to develop the cheapest and simplest to construct NMR.

    11 parts4

Similar boards

  • 2 layersNrf bga, the printed circuit board in 3D

    Nrf bga

    github-linguist/linguist

    Language Savant. If your repository's language is being reported incorrectly, send us a pull request!

    12 parts14kMIT
  • 2 layers66.9 × 74.5 mmDeskHop, the printed circuit board in 3D

    DeskHop

    hrvach/deskhop

    Fast Desktop Switching Device

    12 parts7.9kGPL-3.0
  • 2 layers40 × 15 mmSensors, the printed circuit board in 3D

    Sensors

    google/mozc-devices

    Circuit diagrams and firmware source code for Gboard DIY keyboards

    12 parts3kApache-2.0
  • 2 layers42.7 × 56.5 mmTle6240 driver, the printed circuit board in 3D

    Tle6240 driver

    rusefi/rusefi

    rusefi - GPL internal combustion engine control unit

    12 parts1.2k
  • 2 layers49 × 25 mm5v boost regulator, the printed circuit board in 3D

    5v boost regulator

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    12 parts915
  • 2 layers28.3 × 10.3 mmTap Photosensor PCB, the printed circuit board in 3D

    Tap Photosensor PCB

    VoronDesign/Voron-Tap

    Tap is a nozzle-based z-probe for the V2 and Trident printer designs. The entire toolhead moves to trigger an optical switch. Tap offers many advantages:

    12 parts716GPL-3.0
  • 2 layers25.4 × 70.4 mmTpmsniffer, the printed circuit board in 3D

    Tpmsniffer

    stacksmashing/pico-tpmsniffer

    A simple, very experimental TPM sniffer for LPC bus

    12 parts696

Questions

How big is the ReceiverBoard PCB?

It measures 26 × 44.5 mm and has 2 copper layers, 1.6 mm thick.

What parts does the ReceiverBoard use?

12 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the ReceiverBoard KiCad files?

From the spencerwhyte/SimpleNMR repository on GitHub, at the commit this page was made from: the board is ReceiverBoard/ReceiverBoard.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the ReceiverBoard design in my own project?

Its repository states no licence, so its author keeps all rights: ask spencerwhyte before reusing the design.