Skip to the content
2 layers50 × 50 mm.kicad_pcb, the printed circuit board in 3D

The goal of this project is to develop the cheapest and simplest to construct NMR.

Size
50 × 50 mm
Copper layers
2
Thickness
1.6 mm
Parts
21
Nets
23
Pads
58
Tracks, vias
68, 0
Pours
2
Routed
Yes
KiCad
KiCad 3
Created
16 Apr 2014
Updated
18 May 2014

Overview

.kicad_pcb is an open-source printed circuit board by spencerwhyte, from the spencerwhyte/SimpleNMR repository on GitHub. It is a 2-layer board of 50 × 50 mm with 21 parts on 23 nets, routed with 68 tracks and 0 vias.

Its parts include 3 resistors, 3 diodes, 3 transistors and 3 switches.

README

README.md

Simple NMR

This is my first adventure into NMR and I want to keep everything as simple as possible for the first design.

The process goes a little something like this.

  1. Apply a pre-polarizing pulse to the sample.
  2. Transmit 90 degree pulse
  3. Listen to the FID

Transmit/Receive Board

There is a board which controls the polarization, transmission amplification, and receiver amplification. kicad designs for this board can be found in the RelayBoard folder.

To elaborate on the simple process described above, here is what actually happens.

  1. Apply a pre-polarizing pulse to the sample

    • Configure the relays to disable transmit and receive functionality (To protect the electronics)
    • Turn on the polarization coil
    • Wait some fixed period of time
    • Turn off the polarization coil
  2. Transmit 90 degree pulse

    • Configure the relays to allow transmission
    • Tell GNURadio to output a sine wave at the larmour frequency to the sound card/audio interface
    • Wait 90 degrees worth of time
    • Tell GNURadio to stop the output
    • Configure the relays to disable transmission
  3. Listen to the FID

    • Configure the relays to enable receiving
    • Tell GNURadio to record from line-in
    • Apply a Peak hold FFT to the input signal to see what we received

Amplification Board

There is another board which amplifies the transmitted and received signals. kicad designs for the amplifier board can be found in the AmplifierBoard folder.

Parts

21
QtyValueFootprintReferences
4P***1pin1PIN, 1PIN, 1PIN, 1PIN
32N4401TO92Q1, Q2, Q3
3CONN_3PinHeader3K1, K2, K3
3DIODED4D1, D2, D3
1CONN_2PinHeader2Power1
1CONN_4PinHeader4Control1
1R1R3R1
1R2R3R2
1R3R3R3
1Relay1STDRelayRL1
1Relay2STDRelayRL2
1Relay3STDRelayRL3

More from spencerwhyte/SimpleNMR

2
  • 2 layers26 × 44.5 mmReceiverBoard, the printed circuit board in 3D

    ReceiverBoard

    spencerwhyte/SimpleNMR

    The goal of this project is to develop the cheapest and simplest to construct NMR.

    12 parts4
  • 2 layers50 × 50 mmTransmitter, the printed circuit board in 3D

    Transmitter

    spencerwhyte/SimpleNMR

    The goal of this project is to develop the cheapest and simplest to construct NMR.

    11 parts4

Similar boards

  • 2 layers28.3 × 39.8 mmLevelShifter, the printed circuit board in 3D

    LevelShifter

    gusmanb/logicanalyzer

    24 channel, 100Msps logic analyzer hardware and software

    21 parts5.1kGPL-3.0
  • 2 layers171.2 × 72.9 mmAmiga gfxcard before pour, the printed circuit board in 3D

    Amiga gfxcard before pour

    mntmn/amiga2000-gfxcard

    MNT VA2000, an Open Source Amiga 2/3/4000 Graphics Card (Zorro II/III), written in Verilog

    21 parts1k
  • 2 layers93.9 × 46 mmRectifier, the printed circuit board in 3D

    Rectifier

    rene-dev/stmbl

    AC Servo Driver for STM32F4

    21 parts990GPL-3.0
  • 2 layers45.5 × 42.9 mmEsphome han reader, the printed circuit board in 3D

    Esphome han reader

    hackclub/OnBoard

    💡 Join 1,000 teenagers and make your first PCB with a $100 grant!

    21 parts915
  • 2 layers31.8 × 14.5 mmEsp prog, the printed circuit board in 3D

    Esp prog

    drandyhaas/KiCadRoutingTools

    A set of Python/Rust tools to aid routing in KiCad

    21 parts744MIT
  • 2 layers23.5 × 15.8 mmQuiverAttachPCB, the printed circuit board in 3D

    QuiverAttachPCB

    Arrow-air/project-quiver

    Project Quiver documentation, designs, and project artifacts.

    21 parts617CERN-OHL-S-2.0
  • 2 layers69.9 × 41.3 mmHeaterMeterLCD, the printed circuit board in 3D

    HeaterMeterLCD

    CapnBry/HeaterMeter

    HeaterMeter and LinkMeter Arduino BBQ Controller

    21 parts557MIT
  • 2 layers161.3 × 111.8 mmDoj, the printed circuit board in 3D

    Doj

    kelu124/echomods

    Open source ultrasound processing modules and building blocks

    21 parts463

Questions

How big is the .kicad_pcb PCB?

It measures 50 × 50 mm and has 2 copper layers, 1.6 mm thick.

What parts does the .kicad_pcb use?

21 parts. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.

Where can I download the .kicad_pcb KiCad files?

From the spencerwhyte/SimpleNMR repository on GitHub, at the commit this page was made from: the board is RelayBoard/.kicad_pcb.kicad_pcb. PCBKit opens the board in the browser, with nothing to install.

Can I use the .kicad_pcb design in my own project?

Its repository states no licence, so its author keeps all rights: ask spencerwhyte before reusing the design.