

Main module
40% ortholinear keyboard
- Size
- 228.6 × 81 mm
- Copper layers
- 2
- Thickness
- 1.6 mm
- Parts
- 135
- Nets
- 133
- Pads
- 746
- Tracks, vias
- 951, 152
- Pours
- 2
- Routed
- Yes
- KiCad
- KiCad 10.0 (file 20260206)
- Created
- 7 Sep 2026
- Updated
- 14 Sep 2026
Overview
Main module is an open-source printed circuit board by sky2park, from the sky2park/ostinato repository on GitHub, published under the GPL-3.0 licence. It is a 2-layer board of 228.6 × 81 mm with 135 parts on 133 nets, routed with 951 tracks and 152 vias.
It is built around the RP2040, ESP32-C3-MINI-1 and W25Q128JVSIQ, with the AP2112K-3.3 among its other parts. Its parts include 45 diodes, 20 capacitors, 11 resistors, 4 ICs and 4 connectors. It belongs with the keyboards and input boards and the ESP32, RP2040 and RISC-V boards of this library.
Main components
4RP2040
LQFN-56(7x7)12bit 133MHz 30 LQFN-56(7x7) Microcontrollers (MCU/MPU/SOC) ROHSRaspberry PiMicrocontrollers (MCU/MPU/SOC)ESP32-C3-MINI-1
--40℃~+81℃ -89dBm 2.4GHz 350mA 3V~3.6V 82mA ESP32-C3 Chip On-board PCB Antenna UART - WiFi Modules ROHSRF CrazyWiFi ModulesW25Q128JVSIQ
SOIC-8-208mil-40℃~+85℃ 100,000 cycles 120ms@(32KB) 128Mbit 133MHz 1uA 2.7V~3.6V 20 Years 3ms Power-on reset、Hardware write protection、Software write protection、Write enable latch、Absolute write protection SPI SOIC-8-208mil NOR FLASH ROHSWinbondNOR FLASHAP2112K-3.3
SOT253.3V 600mA CMOS Low Dropout Linear Regulator with EnableDiodes IncorporatedUncategorised
README
README.mdOstinato

처음부터 직접 설계한 40% 오소리니어 기계식 키보드입니다.
Ostinato는 커스텀 PCB, 알루미늄 케이스, 가스켓 마운트 플레이트, 로터리 엔코더, RGB 상태 표시등, USB 연결을 기본으로 하는 45키 오소리니어 키보드입니다. USB 전원이 공급되는 상태에서 Bluetooth 무선 출력을 사용할 수 있습니다.
이 프로젝트에는 PCB와 케이스부터 QMK/Vial 펌웨어와 ESP32-C3 Bluetooth 컨트롤러까지 전체 하드웨어 및 펌웨어 설계가 포함되어 있습니다.
주요 기능
- 40% 오소리니어 레이아웃
- 45키
- MX 호환 스위치
- QMK 펌웨어
- Vial 지원
- USB 및 Bluetooth 연결
- ESP32-C3 기반 Bluetooth 컨트롤러 (USB 전원 필요, 배터리 없음, 단독 무선 작동 불가)
- RP2040 기반 메인 컨트롤러
- 3개의 Bluetooth 연결 슬롯
- 로터리 엔코더
- SK6812MINI RGB LED
- 전용 Bluetooth 상태 표시등
- 레이어 상태 표시
- 가스켓 마운트 플레이트
- 커스텀 알루미늄 상판 케이스
- MJF PA12S 나일론 하판 케이스
- SUS304 스테인리스 스틸 또는 H59 구리 합금 황동 내부 웨이트
사양
| 항목 | 내용 |
|---|---|
| 레이아웃 | 40% 오소리니어 |
| 키 수 | 45 |
| 메인 MCU | RP2040 |
| Bluetooth MCU | ESP32-C3 |
| 펌웨어 | QMK |
| 키맵 설정 | Vial |
| 연결 방식 | USB 기본 / Bluetooth 무선 출력 (USB 전원 필요) |
| 전원 공급 | USB |
| 배터리 | 없음 |
| Bluetooth 슬롯 | 3 |
| 스위치 종류 | MX 호환 |
| RGB LED | SK6812MINI (4개) |
| 로터리 엔코더 | 1개 |
| 마운팅 | 가스켓 마운트 (Poron) |
| 플레이트 | PC |
| 상판 케이스 | 6061 알루미늄 |
| 하판 케이스 | MJF PA12S 나일론 |
| 내부 웨이트 | SUS304 스테인리스 스틸 또는 H59 구리 합금 황동 |
레이아웃
Ostinato는 45키의 컴팩트한 40% 오소리니어 레이아웃을 사용합니다.
작은 크기를 유지하면서 풀사이즈 키보드에 준하는 기능을 제공할 수 있도록 여러 레이어를 중심으로 설계되었습니다.
레이어
펌웨어에는 다음과 같은 주요 레이어가 포함되어 있습니다:
- 기본
- 내비게이션
- 숫자 / 기호
- 기능
- 게이밍
- 게이밍+
- 게이밍 내비게이션
추가 레이어와 키 할당은 Vial을 통해 설정할 수 있습니다.
연결
Ostinato는 USB 연결을 기본으로 사용하며, USB 전원이 공급되는 상태에서 Bluetooth 무선 출력을 지원합니다.
⚠️ 전원 및 Bluetooth 사용 안내
Ostinato는 배터리를 내장하지 않은 키보드입니다. 키보드의 작동과 Bluetooth 사용을 위해 USB 케이블을 연결해야 합니다.
USB 케이블을 연결하지 않은 상태에서는 키보드 단독으로 Bluetooth를 사용할 수 없습니다.
RP2040은 키보드의 주요 기능을 담당하며, ESP32-C3 모듈이 Bluetooth 연결을 제공합니다.
USB
USB 모드에서는 일반적인 USB HID 키보드로 동작합니다.
Bluetooth
키보드는 3개의 Bluetooth 연결 슬롯을 지원합니다:
- Bluetooth 1
- Bluetooth 2
- Bluetooth 3
활성 Bluetooth 슬롯은 키보드에서 직접 선택할 수 있습니다. 펌웨어는 UART를 통해 ESP32-C3와 통신하며 Bluetooth 연결 상태와 슬롯 선택을 제어합니다.
Bluetooth를 사용하더라도 USB 케이블을 통한 전원 공급이 필요합니다. 배터리가 없으므로 USB 전원 없이 Bluetooth만으로 작동할 수 없습니다.
Bluetooth 상태
RGB LED는 Bluetooth 상태를 시각적으로 표시하는 데 사용됩니다. 각 Bluetooth 슬롯에는 전용 상태 표시등이 있습니다.
표시등은 다음과 같은 상태를 구분합니다:
- 광고(Advertising)
- 연결됨
- 페어링
- 오류 / 사용 불가
이를 통해 호스트 기기를 사용하지 않고도 현재 Bluetooth 연결 상태를 확인할 수 있습니다.
RGB 표시등
Ostinato는 4개의 SK6812MINI RGB LED를 사용합니다. 이 LED는 장식용 백라이트가 아니라 기능적인 상태 표시등으로 사용됩니다.
Bluetooth 표시등
3개의 LED가 각각 3개의 Bluetooth 슬롯 상태를 표시합니다.
레이어 표시등
나머지 1개의 LED는 레이어/상태 표시용으로 사용됩니다. 펌웨어는 이 표시등을 특수 키보드 기능의 상태를 표시하는 데에도 사용할 수 있습니다.
로터리 엔코더
Ostinato에는 추가 입력을 위한 로터리 엔코더가 포함되어 있습니다.
엔코더는 QMK와 Vial을 통해 설정할 수 있으며, 활성 레이어에 따라 서로 다른 기능을 할당할 수 있습니다.
아키텍처 및 설계 철학
Ostinato의 목표는 컴팩트한 오소리니어 레이아웃에 일반적으로 대형 키보드에서 제공되는 기능을 결합하는 것입니다.
하나의 무선 컨트롤러에 모든 기능을 의존하는 대신, 메인 키보드 컨트롤러와 Bluetooth 컨트롤러를 분리하는 구조로 설계했습니다:
┌───────────────┐
│ RP2040 │
│ Main Keyboard │
│ Controller │
└───────┬───────┘
│
UART
│
┌───────▼───────┐
│ ESP32-C3 │
│ Bluetooth │
│ Controller │
└───────────────┘이 아키텍처를 통해 RP2040은 핵심 키보드 동작(매트릭스 스캔, 조명, Vial 설정)을 담당하고, ESP32-C3는 Bluetooth 연결 스택을 담당합니다.
펌웨어
Ostinato 펌웨어는 QMK 및 Vial-QMK를 기반으로 하며 **GNU General Public License v2.0 (GPL-2.0)**에 따라 라이선스가 부여됩니다.
firmware/
├── esp32-c3/
├── qmk/
│ └── ostinato/
└── vial/
└── ostinato/- QMK 펌웨어: 매트릭스 스캔, 키맵 및 레이어, 커스텀 키코드, 로터리 엔코더, RGB 상태 표시등, USB 출력, ESP32-C3와의 UART 통신을 담당합니다.
- ESP32-C3 펌웨어: Bluetooth 프로파일 관리, 연결 슬롯, 무선 HID 출력을 담당합니다.
커스텀 키코드
Ostinato는 출력 및 연결 제어를 위해 다음과 같은 커스텀 키코드를 정의합니다:
OUT_USBOUT_BT1OUT_BT2OUT_BT3BT_CLR
이 키코드를 사용하면 USB와 페어링된 3개의 Bluetooth 기기 사이를 즉시 전환할 수 있습니다.
하드웨어
PCB, 케이스, 플레이트 및 관련 CAD 파일을 포함한 Ostinato 하드웨어 설계 파일은 Creative Commons Attribution-NonCommercial 4.0 International (CC BY-NC 4.0) 라이선스에 따라 제공됩니다.
개인적 및 비상업적 사용은 허용됩니다.
상업적 사용에는 저작자의 사전 허가가 필요합니다.
하드웨어는 다음과 같은 모듈형 커스텀 보드로 구성됩니다:
pcb/
├── main-module/
├── led_module/
└── knob-module/- 메인 모듈: RP2040 컨트롤러, ESP32-C3, 다이오드 매트릭스 및 전원 회로를 탑재합니다.
- LED 모듈: 슬롯 및 레이어 상태 표시를 위한 4개의 SK6812MINI 어드레서블 RGB LED를 탑재합니다.
- 노브 모듈: 로터리 엔코더와 브레이크아웃 인터페이스를 탑재합니다.
케이스 및 플레이트
- 상판 케이스: CNC 가공 6061 알루미늄
- 하판 케이스: MJF 3D 프린팅 PA12S 나일론
- 내부 웨이트: 레이저 절단 SUS304 스테인리스 스틸 또는 H59 구리 합금 황동
- 마운팅: PC 플레이트를 분리하는 커스텀 Poron 가스켓 스트립을 사용하여 부드럽고 공명감 있는 바텀아웃을 구현합니다.
제조 및 공차 관련 참고사항
모든 케이스 부품(상판 케이스, 하판 케이스, 내부 웨이트)은 JLCCNC 및 JLC3DP를 통해 프로토타입을 제작하고 검증했습니다. 제조업체와 제작 방식에 따라 공차와 표면 마감이 달라질 수 있으므로, 다른 업체에서 제작한 부품은 테스트되지 않았으며 조립 또는 치수 호환성 문제가 발생할 수 있습니다.
플레이트 절단 프로파일은 plate/ 아래에 DXF 형식으로 제공됩니다:
design.dxfplate.dxf
제조 및 주문 가이드
모든 부품은 특정 제작 업체를 기준으로 설계하고 검증했습니다. Ostinato를 제작할 계획이라면 아래 주문 가이드를 참고하세요.
개요
| 부품 | 소스 파일 | 권장 서비스 | 공정 / 재료 사양 |
|---|---|---|---|
| Top Case | case/top.stepcase/top_theads.pdf (Thread/tapping drawing) | JLCCNC | CNC Machining / 6061 Aluminum (Sandblasted / Anodized) |
| Bottom Case | case/bottom.step | JLC3DP | 3D Printing / MJF Nylon (PA12S) |
| Internal Weight | case/weight.step | JLCCNC | CNC or Sheet Metal / SUS304 Stainless steel or H59 Brass |
| Plate | plate/plate.dxf | Laser cutting service | Laser Cut / 1.5mm Polycarbonate (PC) |
| PCBs | pcb/*/gerber/ | JLCPCB | FR-4 / 1.6mm (or 1.2mm depending on build) |
부품 상세 및 주문 방법
1. 케이스 및 웨이트 (JLCCNC / JLC3DP)
- Top Case:
- File:
case/top.step - 나사산 도면:
case/top_theads.pdf(탭 가공을 주문할 때 이 2D 도면을 함께 첨부하세요) - 서비스: JLCCNC (CNC 가공)
- 재료: 6061 알루미늄
- 표면 처리: 비드 블라스트(샌드블라스트 #150 또는 #180) + 아노다이징(원하는 색상)
- File:
- Bottom Case:
- File:
case/bottom.step - Service: JLC3DP (3D Printing)
- 기술: MJF (Multi Jet Fusion)
- 재료: PA12S 나일론 (검정/염색)
- File:
- Internal Weight:
- File:
case/weight.step - Service: JLCCNC
- 재료: SUS304 스테인리스 스틸 (헤어라인 / 샌드블라스트) 또는 H59 황동
- File:
⚠️ 중요 공차 경고:
CAD 모델, 공차 및 조립 여유 치수는 JLCCNC 및 JLC3DP를 기준으로 조정하고 검증했습니다. 다른 업체나 다른 제작 방식은 테스트되지 않았으며, 부적절한 조립, 수축 편차 또는 조립 문제가 발생할 수 있습니다.
2. 스위치 플레이트
- File:
plate/plate.dxf - 재료: 1.5mm 폴리카보네이트 (PC)
- 서비스: 정밀 레이저 절단이 가능한 업체 (예: JLCCNC 판재 절단 또는 현지 레이저 절단 업체).
3. PCB
- Paths:
pcb/main-module/pcb/led_module/pcb/knob-module/
- Service: JLCPCB
- Ordering Recommendations:
- Upload the Gerber zip files along with the BOM and CPL files from each folder to order the PCB Assembly (SMT) service.
- PCBA Settings:
- Assembly Side: Select
Bottom Sidefor all three modules. - PCBA Type:
main-module: Must be set toStandarddue to assembly constraints of the ESP32-C3 module (bottom pad soldering).led_module&knob-module: SelectEconomy.
- Assembly Side: Select
- ⚠️ Note: The EC11 rotary encoder on the
knob-moduleis not covered by the SMT service; source it separately and solder it by hand (through-hole soldering).
4. 추가 기성 부품 (하드웨어 및 구매)
이러한 표준 하드웨어 부품과 구성품은 별도 제작품이 아니며, 일반 하드웨어 마켓플레이스(예: AliExpress)나 커스텀 키보드 판매처에서 구매할 수 있습니다.
참고: 아래 링크는 제가 프로토타입 제작에 실제로 사용한 동일한 제품 목록과 구매처입니다. 참고용으로만 제공하며, 사양에 맞는 동등한 부품이라면 어떤 제품을 사용해도 됩니다.
| 품목 | 사양 | 수량 | 참고 링크 | 비고 |
|---|---|---|---|---|
| Poron Gasket Strips | 20mm (L) × 3mm (W) × 2mm (T) | 8 | AliExpress | Mounts to plate tabs / case edges |
| FPC Ribbon Cable | 0.5mm pitch, 6-pin, Reverse (Type B), 10–15cm | 2 | AliExpress | Connects main module to LED / knob modules |
| Rotary Encoder | EC11 rotary encoder, 15mm shaft height | 1 | AliExpress | Hand-soldered onto knob-module |
| Encoder Knob | Compatible with EC11 shaft 20 x 13 x 6mm | 1 | AliExpress | Fits selected rotary encoder |
| Unified Daughterboard S1 & Cable | Unified Daughterboard (UDB) S1 with Molex cable | 1 | Vendor Link | Available via various keyboard vendor stores (e.g., CannonKeys, Swagkeys, etc.) |
| Light Guides | Acrylic light pipe / guide 1.5-2.2 or 2.9-3.0 | 4 | AliExpress | Diffuses status LEDs |
| Heat-set Insert | M2 × L3mm × OD 3.2mm | 4 | AliExpress | Case / module mounting |
| Heat-set Insert | M3 × L4mm × OD 4.2mm | 6 | AliExpress | Weight / case and Weight / UDB mounting |
| Screw | M2 × 4mm | 4 | AliExpress | Internal module mounting |
| Screw | M2.5 × 8mm | 4 | AliExpress | Case assembly |
| Screw | M3 × 5mm | 6 | AliExpress | Internal weight / UDB fastening |
빌드 가이드
🚧 상세 빌드 가이드 영상은 현재 준비 중입니다.
저장소 구조
ostinato/
├── case/ # CAD and step/stl files for case parts
├── firmware/
│ ├── esp32-c3/ # ESP-IDF / Arduino BT firmware
│ ├── qmk/ # QMK source and keyboard rules
│ │ └── ostinato/
│ └── vial/ # Vial configuration & keymap files
│ └── ostinato/
├── pcb/
│ ├── main-module/ # Schematic, KiCad layouts, and Gerber files
│ ├── led_module/
│ └── knob-module/
├── plate/
│ ├── design.dxf
│ └── plate.dxf
└── README.md상태
Ostinato는 현재 개발이 진행 중인 커스텀 하드웨어 프로젝트입니다. 실제 리비전을 테스트하는 과정에서 회로도, Gerber 파일 및 펌웨어 구현이 호환성을 깨뜨리는 형태로 변경될 수 있습니다.
크레딧
sky2park가 설계 및 개발했습니다.
- QMK Firmware
- Vial
- Raspberry Pi RP2040 & Espressif ESP32-C3

Parts
135| Qty | Value | Footprint | References |
|---|---|---|---|
| 45 | D_Small | Diode_SMD:D_SOD-123 | D1, D2, D10, D11, D12, D13, D14, D15, D16, D17, D18, D19, D20, D21, D22, D23 +29 |
| 45 | MX_SW_HS | PCM_marbastlib-mx:SW_MX_HS_CPG151101S11_1u | MX1, MX2, MX10, MX11, MX12, MX13, MX14, MX15, MX16, MX17, MX18, MX19, MX20, MX21, MX22, MX23 +29 |
| 12 | 100nF | Capacitor_SMD:C_0402_1005Metric | C1, C5, C6, C9, C10, C11, C12, C13, C14, C15, C19, C20 |
| 5 | 10k | Resistor_SMD:R_0402_1005Metric | R3, R6, R7, R10, R11 |
| 4 | SW_Push | Button_Switch_SMD:SW_SPST_TS-1088-xR020 | SW_ESP_BOOTSEL1, SW_ESP_RESET1, SW_RP_BOOTSEL1, SW_RP_RESET1 |
| 3 | 10uF | Capacitor_SMD:C_0402_1005Metric | C7, C17, C18 |
| 3 | 1uF | Capacitor_SMD:C_0402_1005Metric | C4, C8, C16 |
| 2 | 1k | Resistor_SMD:R_0402_1005Metric | R1, R2 |
| 2 | 220 | Resistor_SMD:R_0402_1005Metric | R8, R9 |
| 2 | 22pF | Capacitor_SMD:C_0402_1005Metric | C2, C3 |
| 2 | 27R | Resistor_SMD:R_0402_1005Metric | R4, R5 |
| 2 | Conn_01x06 | Connector_FFC-FPC:Hirose_FH12-6S-0.5SH_1x06-1MP_P0.50mm_Horizontal | J3, J4 |
| 2 | Molex - 1.00mm 4 Pin | Connector_Molex:Molex_Pico-EZmate_78171-0004_1x04-1MP_P1.20mm_Vertical | J1, J2 |
| 1 | 12MHz | Crystal:Crystal_SMD_3225-4Pin_3.2x2.5mm | Y1 |
| 1 | AP2112K-3.3 | Package_TO_SOT_SMD:SOT-23-5 | U2 |
| 1 | ESP32-C3-MINI-1 | ESP32-C3-MINI-1:ESP32-C3-MINI-1 | U4 |
| 1 | MX_stab | PCM_marbastlib-mx:STAB_MX_P_2u | S41 |
| 1 | RP2040 | Keebio-Parts.pretty-master:RP2040-QFN-56 | U3 |
| 1 | W25Q128JVS | Package_SO:SOIC-8_5.3x5.3mm_P1.27mm | U1 |
More from sky2park/ostinato
2- 2 layers40.5 × 10 mm

- 2 layers28.6 × 19.1 mm

Similar boards
- 2 layers312.5 × 122.3 mm

- 2 layers120 × 25 mm

Grooveboard rp
ianklug/grooveboard
A four-key mechanical keyboard for rhythm games.
47 parts58CC-BY-SA-4.0 - 2 layers220 × 70 mm

Bemini rp
ianklug/bemini
A miniature mechanical keyboard controller with a rotary encoder for staggered-key rhythm games.
70 parts55CC-BY-SA-4.0 - 2 layers84.2 × 100 mm

Fabpack out v5 8
yuz207/agentpad13
agentpad13 — open-source 13-key macropad for agentic work (RP2040, vial-qmk, planar joystick, Raw HID agent-status protocol)
126 parts41 - 2 layers100 × 90 mm

EncoderPad RP2040
jpconstantineau/EncoderPad_RP2040
The EncoderPad RP2040 is a Video Editing Macropad with a 60mm Encoder Wheel. This encoder is made of metal and feels like it will last forever. The EncoderPad uses 9 mechanical switches (Cherry MX type).
62 parts29 - 2 layers76 × 90 mm

- 2 layers75 × 55 mm

Wellfed bench
Isaac-Duarte/wellfed
Open firmware that runs the PETLIBRO Granary PLAF103 pet feeder on your own Wi-Fi: no cloud, no account. Early and in testing.
93 parts8MIT - 2 layers19.9 × 29 mm

Questions
How big is the Main module PCB?
It measures 228.6 × 81 mm and has 2 copper layers, 1.6 mm thick.
What parts does the Main module use?
135 parts, built around the RP2040, ESP32-C3-MINI-1, W25Q128JVSIQ and AP2112K-3.3. The full list of its parts is on this page, with links to each part's symbol and footprint where PCBKit's library has them.
Where can I download the Main module KiCad files?
From the sky2park/ostinato repository on GitHub, at the commit this page was made from: the board is pcb/main-module/pcb.kicad_pcb and its schematic pcb/knob-module/knob.kicad_sch. PCBKit opens the board in the browser, with nothing to install.
Can I use the Main module design in my own project?
Its repository publishes it under the GPL-3.0 licence: you may reuse it on that licence's terms (keep the author's notice, and for a copyleft licence share your changes alike).